Purchased this trigger. It works as said and feels great. This paired with the spring kit he offers (not the PRP) makes for a crisp break, & lighter shorter pull. Would recommend to others!
Original xds or mod2 ,,, im reading that some mod2 owners are having issues but it could just be that there doin it themselves ... would be nicw to get some good feed back
Just installed needed a little smoothing out for my specific xds but fit is AMAZING with the prp spring set (installed before I purchased) this is an amazing trigger on my absolutely favorite single stack 9mm take up is extremely minimal 0 overtravel crisp break 110% recommend this trigger to anyone who owns an xds!!!
I just got an XDS .45 same as on the table 3.3 stock everything though. There's a little a little creep in the trigger as you pull to fire,so in your opinion the Einer trigger upgrade would take care of that? I could switch to a Ruger sr9c but I love the XDS.
Installed on the xds mod 2 45 and have to squeeze trigger with two hands to get striker to fire. There must be a slight difference on the mod 2s. Have to revert back to original.
Having same issue as above, on XDS mod 2.0 9mm where it's a 50 pound trigger pull and striker doesn't drop until trigger is dead smashed against the frame.
Same issue. Just installed tonight on my XDs 45 pre Mod 2 with the recall done. It went in easy except for that grip safety arm and spring. Once I figured out where the arm went everything went smooth. There is an annoying light snap when the trigger safety slides by and then you squeeze until you finger goes numb and it eventually breaks. My super long creep however, is gone! But yes 50lb pull!
I put my all together and when press the safety's and pull the trigger it works but the last mm before it fires is harder to pull like the trigger is slightly to big
Excellent Video Brother! Didn't add the new trigger, but you helped me figure out why my trigger wasn't breaking!!! Thank you and God Bless the Conservative America!!! FJB!!!
After removing the lower parts from the frame to get my gun cerakoted I put everything back together. Now when I hit the mag release the button stays to the side I push it to. Not allowing me to reseat the next mag. Any advice on what I did wrong?
Probably just a build up of the Cerakote in the mag release channel. Take out the release and sand all the Cerakote out with 240 grit sandpaper, that should do the trick.
I just got an XDS .45 same as on the table 3.3 stock everything though. There's a little a little creep in the trigger as you pull to fire,so in your opinion the Einar trigger upgrade would take care of that? I could switch to a Ruger sr9c but I love the XDS.
Installed this trigger on my XDs Mod.2 along with your spring kit. Trigger is not breaking until it’s kitting the back of the trigger frame. Don’t know what’s going on with this but definitely hard to shoot with the break at that point.
my sear spring fits into the slot on the sear but everytime i compress the spring into shape the L side slips out of the slot everytime because its not fully flush but i see on this video you don't have the issue nor you do you have to pinch it into place. i dont understand why.
Brandon, this Charlie, how is the xde trigger project going. Probably be out you way next week, with S&W Shield. Nice job on that trigger today. Regards to All !
The Delta Point Pro is too big for the slide, but if you have the original Delta Point it is doable. Though honestly the Shield Sights RMS/RMSc or a JPoint would be better. We mill deep enough for them to co witness the stock iron sights.
I haven’t heard anything from Galloway saying that there spring and trigger upgrade either needs to be done together OR that the trigger and spring set IS NOT made for the spring field XDS mod 2 any info would appreciated Galloway
I bought one and it wouldn't even fit in the trigger retainer. 3d printed and wast cleaned up on the inside. Safety was very stiff. Returned. I feel the one in this video was pre fitted before the filming. Rather dissapointed as Galloway is known for quality products.
1 Remove the Takedown lever 2 Remove the Trigger Pivot Pin 3 Remove the locking block Pin 4 Remove the locking block 5 Gently lift the trigger from the well 6 Press the Locking block pin back in to keep trigger lever elevated. 7 Press out trigger pin 8 Press the Einar trigger pin to depth and place the trigger bar onto it 9 Press Einar trigger pin home (evenly in the middle of the trigger) R remove the locking block pin you were using to keep the trigger arm up and guide the trigger into the trigger well. Now reverse the assembly order from step 5 -> 1 This ensures the grip saftey assembly remains intact and has no assembly mistakes, this is within the swing arc of the trigger arm without torque (can be done with fingertips) This installation process is not the one advised in the video or endorsed by GallowayPrecision, I was installing the trigger and saw this solution as superior.
Purchased this trigger. It works as said and feels great. This paired with the spring kit he offers (not the PRP) makes for a crisp break, & lighter shorter pull. Would recommend to others!
Original xds or mod2 ,,, im reading that some mod2 owners are having issues but it could just be that there doin it themselves ... would be nicw to get some good feed back
Just installed needed a little smoothing out for my specific xds but fit is AMAZING with the prp spring set (installed before I purchased) this is an amazing trigger on my absolutely favorite single stack 9mm take up is extremely minimal 0 overtravel crisp break 110% recommend this trigger to anyone who owns an xds!!!
Hi Joshua, do you have the PRP spring kit only? or do you have the kit with disconector? Thank you
I just got an XDS .45 same as on the table 3.3 stock everything though. There's a little a little creep in the trigger as you pull to fire,so in your opinion the Einer trigger upgrade would take care of that? I could switch to a Ruger sr9c but I love the XDS.
Just installed mine! Thanks. I've had it for awhile now maybe 6ish months I noticed my trigger I got wasn't 100% the same as your but still works fine
Thanks for the tip @6:25 about the trigger/ safety not working together. That was the problem I was having. Fixed. 😎👍🏻
Glad to help.
Installed this last week. Had to dry fire a bit to get it to "settle" . Feels pretty good now. Going to take it to the range tomorrow .
Thank You Brandon & Galloway.
Could you please show a full how to video on the set up you have on this pistol please. Or drop links on everything you have on this pistol please
www.gallowayprecision.com
XDS Performance
Just got mine installed the grip safety pin was a pain in the ass kept falling out just like they said but it’s in and I love it
Make sure the grip safety is functioning. If you don't have it just right it will fire without the grip safety engaged.
Installed on the xds mod 2 45 and have to squeeze trigger with two hands to get striker to fire. There must be a slight difference on the mod 2s. Have to revert back to original.
Having same issue as above, on XDS mod 2.0 9mm where it's a 50 pound trigger pull and striker doesn't drop until trigger is dead smashed against the frame.
That's the same prob I have and I have the xds 45
Same issue. Just installed tonight on my XDs 45 pre Mod 2 with the recall done. It went in easy except for that grip safety arm and spring. Once I figured out where the arm went everything went smooth. There is an annoying light snap when the trigger safety slides by and then you squeeze until you finger goes numb and it eventually breaks. My super long creep however, is gone! But yes 50lb pull!
Did anyone ever figure out the issue and if so is it worth putting in with or without the spring kit??? Thanks fellas
No one has ever got back to me. I'm still waiting lol
I put my all together and when press the safety's and pull the trigger it works but the last mm before it fires is harder to pull like the trigger is slightly to big
Email tech@gallowayprecision.com for technical help.
Excellent Video Brother! Didn't add the new trigger, but you helped me figure out why my trigger wasn't breaking!!! Thank you and God Bless the Conservative America!!! FJB!!!
Glad to help
Will this work on my xds 9 mm 4.0” barrel that already has PRP springs etc on it?
Even with all that on it, I hate the longgg reset on the trigger.
where did you get your extended threaded barrel????
If you find out let me know!!
Did you machine the slide to accept the red dot?
After removing the lower parts from the frame to get my gun cerakoted I put everything back together. Now when I hit the mag release the button stays to the side I push it to. Not allowing me to reseat the next mag. Any advice on what I did wrong?
Probably just a build up of the Cerakote in the mag release channel. Take out the release and sand all the Cerakote out with 240 grit sandpaper, that should do the trick.
I just got an XDS .45 same as on the table 3.3 stock everything though. There's a little a little creep in the trigger as you pull to fire,so in your opinion the Einar trigger upgrade would take care of that? I could switch to a Ruger sr9c but I love the XDS.
It should help with that yes.
@@GallowayPrecision Thanks I really appreciate your insight and response
Can you please tell me what optic that is it’s so hard trying to find one for the .45 Acp 😂
Installed this trigger on my XDs Mod.2 along with your spring kit. Trigger is not breaking until it’s kitting the back of the trigger frame. Don’t know what’s going on with this but definitely hard to shoot with the break at that point.
You need fit the trigger to tolerances of your particular pistol, email tech@gallowayprecision.com for help.
Did you work the problem out ,,, still trying to make a decision
my sear spring fits into the slot on the sear but everytime i compress the spring into shape the L side slips out of the slot everytime because its not fully flush but i see on this video you don't have the issue nor you do you have to pinch it into place. i dont understand why.
Not sure why. Be glad to take a look. Could you please contact us through our website with some pictures?
debating on Changing out springs and sear, etc.. on the XDS or just buying another pistol.. any advice youtubers?
What and where can I get that barrel?
EFK Firedragon makes them.
GallowayPrecision thank you!
Yes thanks. Finally
What barrel is that?
What red dot sight is that? And how did you attach it?
The original Delta Point, and we milled the slide to accept the optic.
GallowayPrecision I need that!!!
How did u get a threaded barrel
Is this still working correctly in the mod2 ... I only ask because i want to purchase but it seems the mod2 is having similar issues
i have the mod2 newer one i did everything but my trigger wont reset properly any advice
Hi Bryce, Please contact us through our website for proper assistance in resolving the installation issue you are having. Thanks.
What kind of mount and optic are those?
It isn't a mount, we hard milled the slide for the original Leupold Delta Point, before it became the giant optic it is now.
Could not get it to work at all!! Went back to spring kit with stock trigger!
Did you contact our tech through our website for assistance with your installation? Something was wrong with the installation.
Do you have a flat trigger for the XD series?
Will this trigger work with the xd 3"
What barrel is that and where might I be able to purchase it?
It was a custom barrel. Company is no longer in business.
@@GallowayPrecision ok thank you
Were did you get your threaded barrel can u send me a link or send me in the right direction
EFK Firedragon. efkfiredragon.com/springfield-xd-threaded.html
Any chance you can update the link I get an error code, hopefully this product is still available
Brandon, this Charlie, how is the xde trigger project going. Probably be out you way next week, with S&W Shield. Nice job on that trigger today. Regards to All !
We'll have it ready by the end of this quarter.
Would like to know more about the delta on the xds could you mill my xds 4.0 for one ?
The Delta Point Pro is too big for the slide, but if you have the original Delta Point it is doable. Though honestly the Shield Sights RMS/RMSc or a JPoint would be better. We mill deep enough for them to co witness the stock iron sights.
Any shooting reviews on this yet
Haven't had the chance yet, my backyard range is still a soupy mess with all the rain we've been getting.
Just ordered one amazing deal thanks guys will post review when its installed and tested
joshua deuso did you test this yet? What do you think of it? I hate the stock trigger with a passion
How many inches is your barrel now ?
Right around 4 inches. It's an EFK Firedragon threaded barrel specifically made for the XDS series.
I haven’t heard anything from Galloway saying that there spring and trigger upgrade either needs to be done together OR that the trigger and spring set IS NOT made for the spring field XDS mod 2 any info would appreciated Galloway
They both work in the Mod2, post pistols are exactly the same internally they only changed the extractor and the grip zone.
GallowayPrecision thats fantastic did they change the extractor removal to how the Glock has it? the roll pin was scrapped
I bought one and it wouldn't even fit in the trigger retainer. 3d printed and wast cleaned up on the inside. Safety was very stiff. Returned. I feel the one in this video was pre fitted before the filming. Rather dissapointed as Galloway is known for quality products.
1 Remove the Takedown lever
2 Remove the Trigger Pivot Pin
3 Remove the locking block Pin
4 Remove the locking block
5 Gently lift the trigger from the well
6 Press the Locking block pin back in to keep trigger lever elevated.
7 Press out trigger pin
8 Press the Einar trigger pin to depth and place the trigger bar onto it
9 Press Einar trigger pin home (evenly in the middle of the trigger)
R remove the locking block pin you were using to keep the trigger arm up and guide the trigger into the trigger well.
Now reverse the assembly order from step 5 -> 1
This ensures the grip saftey assembly remains intact and has no assembly mistakes, this is within the swing arc of the trigger arm without torque (can be done with fingertips) This installation process is not the one advised in the video or endorsed by GallowayPrecision, I was installing the trigger and saw this solution as superior.
Anyone test this to 1000 rounds?
Slow down and be sure to warn people of loose parts poorly made video and narration
I just installed this trigger. Followed him step by step with no issues. Narration is perfect, great detail and explanation
@@jamessummers9361 interesting how he has to say your probably mfing him for not warning you about the spring falling out then.
Where can one get that barrel setup you have??
Sorry, that was a one-off barrel. Not sure of anyone currently making a threaded barrel for the XDS.
Is this trigger ok to install without having the spring kit installed?
Where did you get a threaded barrel?
Tornado Technology extended and threaded it for us.