Although I have a different gate opener, this setup trick worked the same had to press a few times until it programed but it worked.Thanks for the good straight to the point video. 👍
Thank you sir for the video, I bought a keypad and tried to connect it to my gate opener and screwed up everything, was so worried to get it going again and finally found your video and it worked perfectly. Now I will sleep again. Thanks again.
Thank you. I may have gotten instructions slightly wrong, as I have had to add a few more remotes since this video but it still works as described. Glad it helped you
Thank you for your video. Mines somehow got broken so I needed a new circuit board, I'm only seeing universal ones I went ahead and purchase now I have no clue how to connect it. as everything seems different. can you offer any suggestions?
Unfortunately I do not believe it does. There is a special frequency (433 mHz) I believe, but I have not been able to get it to ever work with any remote other than the manufacturer supplied
Only seems to work with the remotes from the manufacturer. I also buy my extra remotes on Amazon (where I bought the opener) but I only purchase them from the original seller CO-Z
I purchased the additional remote directly from the seller I purchased the gate opener from on Amazon. Here's a link the item listing - www.amazon.com/dp/B0197QYJCC/ref=cm_sw_r_tw_dp_JDVMK66H5C6HJH5N71VG?_encoding=UTF8&psc=1
Well I can't upload a picture so let me try and explain this best I can. This is assuming using the same sensor I am using. Facing the panel with the covers off.... On the panel you have 2 green plugs at the bottom that the wiring going into the board is hooked to. The one on the left I have nothing plugged into it has 4 slots. The one on the right controls the motor and should have 6 slots. 3 should be empty slots to the right hand side labeled IR GND 24VDC The IR sensor has 4 wires you want to use. Grey, white, brown, blue Grey goes to IR White and brown go to GND (twist them together) Blue goes to 24VDC After those are connected its just a matter of attaching your sensor and the reflector so when something crosses the beam the gate stops and reopens. Hope that helps.
I tried doing this myself. This particular system only works with the remotes purchased directly from the supplier. You can find one here and program it the way I've shown in this video. www.amazon.com/dp/B0197QYJCC/ref=cm_sw_r_cp_apa_fabc_L4kPFbJTHX6DK?_encoding=UTF8&psc=1
Hello, I have the same device. My remote controls are old, I bought a new one 3-4 times, but it did not work. When I press the control, the light turns on, but the door does not close and open. can you help me
I don't know that I can help. It might be a problem with the actual board(computer). I have had to just keep trying over and over sometimes, but as long as you bought the remotes directly from CO-Z it should work. 3rd party remotes with the same frequency just won't work. I've tried myself. Sorry.
If sensors you mean the magnetic limit switches, I don't know think so. Adding the remotes is done inside the panel box so if you're adding new or extra remotes you'd just need to have power so you can sync them to the unit.
@@nathanielross1239 This is a brand new install. The magnetic limit switches are installed and work. Hit the learn button and can see when I push the big top button on the remote I see the light lighting up on the control board but the gate doesn't do anything. The manual test works each way open and closes. Not sure why remote won't program.
@@gluc0se the light should flash, then you push the top button on the remote until it syncs. Once it syncs it should start opening and closing. You may have to keep repeating the process. Make you are using the manufacturer supplied remotes, not a 3rd party remote, 3rd party remotes will appear to sync but they just never will.
@@nathanielross1239 Thanks for your help Nathaniel. Once I realized I was trying to program the knockoffs instead of the original remote thanks to your tip I was able to easily get the gate programmed.
I have questions when you install motor on the left of gate like yours do you have do anything different cause the books says that default on motor is for right side mounting thanks.
I don't remember making any changes other than positioning the stop limit magnets opposite of what the book said. One stops it from opening too far and the other from closing too far. One side is mounted just a couple inches higher than the other. It was little trial and error but pretty easy once I figured it out. When you press the remote, the motor will keep spinning and spinning until one of the magnets crosses by it. When you press the remote again it will stop and just go the other way.
Unfortunately there is no way to reprogram the remotes. They are on a set frequency. I have tried using other brand remotes myself which are the same frequency and they just won't pair with the motor. You have to buy the remotes directly from the company that sells this gate opener. I believe they also sell a keypad, however, I have no use for one so I don't know the method of connecting or programming one.
What do I do if I install two gate openers within 100 ft. and when I use one remote both gate openers open at the same time ? Please if You can help , thank You
That seems kind of strange. I would only expect that if you programmed the same remote on both units. May want to reach out to the manufacturer for that one. I don't know how to delete a remote, just how to add one.
I do not believe this model has a sun visor option. I tried programming one that uses the same frequency and it didn't work. The only ones that work with this opener have to be purchased from the manufacturer.
The process is frequency learning. I've had to do it multiple times. Press the black button on the panel, then click the top button on the new remote. These must be remotes from CO-Z otherwise they just won't work. Once it recognizes the signal the gate will open and close as it should.
That doesn't seem normal. I had issues where mine wouldn't close after installing the infrared sensor but I realized later that was because the reflector had water droplets on it and threw off the infrared beam - also only ever happened when it rained. You may have a defective remote that has a sticky button?? Just a guess.
Thank you! Short and to the point, very well and easy explained.
Although I have a different gate opener, this setup trick worked the same had to press a few times until it programed but it worked.Thanks for the good straight to the point video. 👍
Thank you sir for the video, I bought a keypad and tried to connect it to my gate opener and screwed up everything, was so worried to get it going again and finally found your video and it worked perfectly. Now I will sleep again. Thanks again.
Very good video. We have the system and it works incredibly well.
Great to hear!
Thank you very much for putting this video together; the manual instructions are beyond lame.
Very very very helpful!! Thanks so much for the vid!!
Thanks for your tutorial. It helped so much. 👍🏻
Gracias me ha servido mucho, fácil y efectivo. Dios te bendiga 🙏
Very nice vid! Straight forward !
Thank you. I may have gotten instructions slightly wrong, as I have had to add a few more remotes since this video but it still works as described. Glad it helped you
Thank you your vidz really helped me install it.
This worked for me within 5 seconds. Thank you for this tutorial!!
Thanks for the video! Couldn’t figure it out until I came across this
Thanks. I'm glad I could help. The instructions included are terrible but I was able to dechier them and come up with this tutorial.
Thanks man for your help was easy
Thanks....Nate...👍😎
Thank you boss!!
Thank I just program my gate remote ❤
Good vidio
Thank you for your video. Mines somehow got broken so I needed a new circuit board, I'm only seeing universal ones I went ahead and purchase now I have no clue how to connect it. as everything seems different. can you offer any suggestions?
Does this method works on cars also?
Unfortunately I do not believe it does. There is a special frequency (433 mHz) I believe, but I have not been able to get it to ever work with any remote other than the manufacturer supplied
Do you know if the car mirror control can be programed to thsi gate opener?
I do not believe it can. I have tried using remotes with 433 mhz frequency and they don't work.
@nathanielross1239 gotcha! Bummer, thanks!
Hello just bought this unit… can you tell me if the power cable came with the unit and what other tools are needed for installation thank you
Does it work with the remote u also buy from Amazon? Cuz mine came with 2 bt I went n bought more cuz I have more cars n family members.
Only seems to work with the remotes from the manufacturer. I also buy my extra remotes on Amazon (where I bought the opener) but I only purchase them from the original seller CO-Z
I’m programming more remotes and it works but then it stops working. I can’t find anything on google. Any thoughts?
Have you tried to connect to the cars opener?
Thank you
Where did you purchase the additional remote?
I purchased the additional remote directly from the seller I purchased the gate opener from on Amazon. Here's a link the item listing
- www.amazon.com/dp/B0197QYJCC/ref=cm_sw_r_tw_dp_JDVMK66H5C6HJH5N71VG?_encoding=UTF8&psc=1
I have a question, do you know how to adjust it so that it stops when closing?
What's the frequency required on the remotes for these model the 433mz or the lower 3 hundred one thanks
I believe it is 433 mHz. I have failed to get it to work myself using 433 remotes from anyone other than the manufacturer.
Will the same remote but with blue led work with same motor???????
As long as you purchased it directly from the vendor it should work just fine. I have red and blue led remotes.
It help me as well
Good video,On the CO-Z opener where do I connect the sensor wires?
I will have to check the specifics when I am back home. It's very simple.
@@nathanielross1239 Oh,Thanks I would appreciate that
Well I can't upload a picture so let me try and explain this best I can. This is assuming using the same sensor I am using.
Facing the panel with the covers off.... On the panel you have 2 green plugs at the bottom that the wiring going into the board is hooked to. The one on the left I have nothing plugged into it has 4 slots. The one on the right controls the motor and should have 6 slots.
3 should be empty slots to the right hand side labeled
IR
GND
24VDC
The IR sensor has 4 wires you want to use. Grey, white, brown, blue
Grey goes to IR
White and brown go to GND (twist them together)
Blue goes to 24VDC
After those are connected its just a matter of attaching your sensor and the reflector so when something crosses the beam the gate stops and reopens.
Hope that helps.
www.amazon.com/dp/B001LFPB0M/ref=cm_sw_r_cp_apa_fabc_8mVVFbEA6S6W1?_encoding=UTF8&psc=1
In case you needed to know the sensor I am using
@@nathanielross1239 Thank you, so much.
Hi bro whats the frequency of the remote. I used 433 and its not working
I tried doing this myself. This particular system only works with the remotes purchased directly from the supplier. You can find one here and program it the way I've shown in this video.
www.amazon.com/dp/B0197QYJCC/ref=cm_sw_r_cp_apa_fabc_L4kPFbJTHX6DK?_encoding=UTF8&psc=1
@@nathanielross1239 thanks a lot mate
Hello, I have the same device. My remote controls are old, I bought a new one 3-4 times, but it did not work. When I press the control, the light turns on, but the door does not close and open. can you help me
I don't know that I can help. It might be a problem with the actual board(computer).
I have had to just keep trying over and over sometimes, but as long as you bought the remotes directly from CO-Z it should work.
3rd party remotes with the same frequency just won't work. I've tried myself. Sorry.
@nathan where can I buy the original remotes?
Nathaniel, do you know if you have to have the sensors installed before the remotes will program?
If sensors you mean the magnetic limit switches, I don't know think so. Adding the remotes is done inside the panel box so if you're adding new or extra remotes you'd just need to have power so you can sync them to the unit.
@@nathanielross1239 This is a brand new install. The magnetic limit switches are installed and work. Hit the learn button and can see when I push the big top button on the remote I see the light lighting up on the control board but the gate doesn't do anything. The manual test works each way open and closes. Not sure why remote won't program.
@@gluc0se the light should flash, then you push the top button on the remote until it syncs. Once it syncs it should start opening and closing. You may have to keep repeating the process. Make you are using the manufacturer supplied remotes, not a 3rd party remote, 3rd party remotes will appear to sync but they just never will.
@@nathanielross1239 Thanks for your help Nathaniel. Once I realized I was trying to program the knockoffs instead of the original remote thanks to your tip I was able to easily get the gate programmed.
What infrared did you used for sensor
I am using this... www.amazon.com/gp/product/B001LFPB0M/ref=oh_aui_detailpage_o05_s01?ie=UTF8&psc=1
Is it same way with visor remotes?
I don't think so unless the same frequency. So sorry I took over a year to answer you.
I have questions when you install motor on the left of gate like yours do you have do anything different cause the books says that default on motor is for right side mounting thanks.
I don't remember making any changes other than positioning the stop limit magnets opposite of what the book said. One stops it from opening too far and the other from closing too far. One side is mounted just a couple inches higher than the other. It was little trial and error but pretty easy once I figured it out. When you press the remote, the motor will keep spinning and spinning until one of the magnets crosses by it. When you press the remote again it will stop and just go the other way.
@@nathanielross1239 thank you
but how do you program the remote to open all the way?
My neighbor have the same gate. How I can reprogram my remotes to have a different code.
Unfortunately there is no way to reprogram the remotes. They are on a set frequency. I have tried using other brand remotes myself which are the same frequency and they just won't pair with the motor. You have to buy the remotes directly from the company that sells this gate opener.
I believe they also sell a keypad, however, I have no use for one so I don't know the method of connecting or programming one.
Ths.
What do I do if I install two gate openers within 100 ft. and when I use one remote both gate openers open at the same time ? Please if You can help , thank You
That seems kind of strange. I would only expect that if you programmed the same remote on both units. May want to reach out to the manufacturer for that one. I don't know how to delete a remote, just how to add one.
@@nathanielross1239 thank You So much , Love Your Show !!
How can i fine wat remote goes with the gate opener..I'm looking 4a sun visor remote
I do not believe this model has a sun visor option. I tried programming one that uses the same frequency and it didn't work. The only ones that work with this opener have to be purchased from the manufacturer.
@@nathanielross1239 thx u
Your doing it wrong buddy!!! You have to hold the black button down for a second then it beeps then you push the remote button down and it will work!
I must have a flawed system because mine doesn't beep. This is the only method that has worked on multiple remotes. Thanks
Wheni install sensor when it detects something that block the sensor it closes it doesnt open i swap the N.C and NO already same.thing
I followed the steps but when i push the button it only sounds like a clik, but it won't open... What am i doing wrong?
The process is frequency learning. I've had to do it multiple times. Press the black button on the panel, then click the top button on the new remote. These must be remotes from CO-Z otherwise they just won't work. Once it recognizes the signal the gate will open and close as it should.
Ok where does the white wire that is left out go
Is it a signal wire
@@anthonydejesus4995 mine has an extra wire. It's doesn't get connected to anything.
Thank you very much but how did you program the controls
I have an issue with mine. The gate opens on its own sometimes. Any ideas whats causing it ?
That doesn't seem normal. I had issues where mine wouldn't close after installing the infrared sensor but I realized later that was because the reflector had water droplets on it and threw off the infrared beam - also only ever happened when it rained.
You may have a defective remote that has a sticky button?? Just a guess.
I know it's been a year since I first replied but possibly you have or had the chain too tight?
🤣🤣🤣 it’s very simple but if you don’t know how to remove a screw just break the panel no big deal 😂😂😂
Screws? Who needs screws?! 🤣
DOES NOT WORK
I don't know why it wouldn't? I still continue programming remotes this exact way.
You might want to see if the manufacturer can assist you.
@@nathanielross1239 your tutorials suck