Is repairing an S17 model similar to repairing a DR5? I see the hash boards are pretty much alike, but maybe something differs... I just runned into a falling heat sink problem.
Do you have an idea what type of solder it was originally manufactured with? Possible lower melting point would cause heat sink to fall off pre maturely.
Excellent video. Just happen to be working on a 17 right now with the same issue. But I can't find any 130 degree solder & flux anywhere. The only 130 I've found is resin core and .5 in size. Can you send me a link?
@@пижонолегов как чипы выращивать, я хз. Проверяются снятые чипы на ток потребления, запаянные просто по контрольным точкам. Чип пайка на припой 200С+, радиатор пайка на припой 150С.
@@MrFutu8 один человек показывал, мол берёт чип, подсоединяет лабораторный блок установив на 1.5 вольта и подсоединяет на большой контакт минус на маленьком плюс, и смотрит по потреблению если 0.2-0.5 то норм если выше Ампера то хреновый, у меня т17е там чипы AB в конце, пробовал так он сразу греется и потребление больше, а тип который показывал ремонтировал т 17 просто, незнаю можиш рассказать как проверять чипы годный не годный
does it matter which hashboard goes in which slot? i assume no, but just making sure. I repaired some heat sinks, but the board is still not working with no other apparent damage
Hello antminer repair I was trying to figure out a way to reach out to you but this was the only way. I have a S 17 Pro which I overheated and six heat sinks fell off and one is loose it’s the heat sinks on the chip side I wanted to get your opinion. Most of the Solder on the chip part is off but the heat sinks still have Solder on them I am afraid to resolder them and throw a solder ball and short the circuit. I have cool master high-performance thermal paste is it safer to try to remove all the solder from the heat sink and the chips and use the thermal paste or do I place the heat sink with some chip quick on the chip and heat the heat sink and try to fuse it again .what should I do please and thank you?
![[#2024MAMA] ROSÉ (로제), Bruno Mars - APT. | Mnet 241122 방송](http://i.ytimg.com/vi/dgGqD28J6aQ/mqdefault.jpg)
This was more informative about 'tech work' in an 18 minute video than a 4 year EE degree. Keep up the good work
Just subscribed! Joined discord!
Great video. I appreciate the content.
I appreciate that!
thanks for the videos its a real help , do you sell boards?
Is there any way you can tell me what to buy, like desoldering gun, flux, etc?
please help me s17+. unequal voltage ranges. test is still enough number of chips . The signal pins are still there. I'm stuck
Is repairing an S17 model similar to repairing a DR5? I see the hash boards are pretty much alike, but maybe something differs...
I just runned into a falling heat sink problem.
What solder or glue are you using? Do you have a special link where I could purchase some?
Thanks.
Great videos, keep up the good work!
what if put thermal paste?
Please help me i need info about product that use with heat to adhasive the sink please ?
Do you have an idea what type of solder it was originally manufactured with? Possible lower melting point would cause heat sink to fall off pre maturely.
Спасибо.
Не за что мой друг.
Excellent video. Just happen to be working on a 17 right now with the same issue.
But I can't find any 130 degree solder & flux anywhere. The only 130 I've found is resin core and .5 in size.
Can you send me a link?
Look at chipquik.com
Do you have experience with black glue that zeus sells? I was thinking that is what is used for replacing heat sinks.
Not on the 17 series machines. Except maybe the T17e. They must be soldered
hi. can you tell me wich model of chip is good for t17 and t17+
Please look at zeusbtc.com and look for the BM1397 chip. There is a table in the description that maps chips to miners. Thanks!
Why my hashboard asic 32#
make a video on t17e repair
I probably would if I had one.... right now I don't have one!
Чего тебя интересует?
Как чипы правильно выращивать, как их проверять, Поподробнее пожалуйста. Какой припой, температура
@@пижонолегов как чипы выращивать, я хз. Проверяются снятые чипы на ток потребления, запаянные просто по контрольным точкам. Чип пайка на припой 200С+, радиатор пайка на припой 150С.
@@MrFutu8 один человек показывал, мол берёт чип, подсоединяет лабораторный блок установив на 1.5 вольта и подсоединяет на большой контакт минус на маленьком плюс, и смотрит по потреблению если 0.2-0.5 то норм если выше Ампера то хреновый, у меня т17е там чипы AB в конце, пробовал так он сразу греется и потребление больше, а тип который показывал ремонтировал т 17 просто, незнаю можиш рассказать как проверять чипы годный не годный
Any chance I could send you a t17 miner that needs work? Many broken chips and detached heat sinks. My guess is the boards got dropped..
Hi, You might want to ask on our discord server if anyone can help you. Right now, I'm very full with projects. Thanks.
does it matter which hashboard goes in which slot? i assume no, but just making sure. I repaired some heat sinks, but the board is still not working with no other apparent damage
No, it doesn't matter. Thanks
Why You have not a Quick 861 DW. I feel how you are suffering.))))
Bad chip = good chip.
Hello antminer repair
I was trying to figure out a way to reach out to you but this was the only way. I have a S 17 Pro which I overheated and six heat sinks fell off and one is loose it’s the heat sinks on the chip side I wanted to get your opinion. Most of the Solder on the chip part is off but the heat sinks still have Solder on them I am afraid to resolder them and throw a solder ball and short the circuit. I have cool master high-performance thermal paste is it safer to try to remove all the solder from the heat sink and the chips and use the thermal paste or do I place the heat sink with some chip quick on the chip and heat the heat sink and try to fuse it again .what should I do please and thank you?
Please join the discord server where you can share photos and get many opinions. thanks
awful work
Hey can you send me a new Discord invite, the link is expired?
discord.gg/WTxkyEnCQB