@Maxim Ibragimov wrote an excellent comment: "One of the common causes of toner adhesion to a thermistor is the use of compatible toner. Due to a low or high temperature, the toner begins to stick to the thermal film / Teflon roll, and from it goes to the thermistor. Or, part of the toner (particles) that are not baked, parrying in the air, settle on the thermistor. On the original toner, this can also be observed, but its amount is not critical to affect the part, because by this time the unit will use up its resource. The cause of this problem is not the only one, but compatible toner is in principle a common cause, the problems of which appear during the operation of the machine." THANK YOU @Maxim Ibragimov
Good video and I watched the whole video, I did not see you inspect, service or replace the Thermistors that caused the damage. what do you use to clean Thermisteors without "killing" them?
I usually replace these elements with new ones. Usually cleaning works for a short time, and I don't like the risk. Check out my gadget store 🤩🥳 MOVIE STUDIO SHOP: my-store-7469644.creator-spring.com/ 🔥🔥 TH-cam SUPPORT: th-cam.com/channels/OHtXTtGHj33pUm8Gf2FH3A.htmljoin 😁😆 PATREON: www.patreon.com/CopyExpertMovieStudio 🔥💥 PATRONITE: www.patronite.pl/1796
It's not in the video, but I only cleaned the thermistor. Some toner has built up on the thermistor and it has hardened and damaged the roller. It was enough to touch the thermistor with a finger and the toner fell off. Everything is still working normally. Only the question arises: why is there this problem with the toner build-up on the thermistor in this model of copiers?
@Maxim Ibragimov You explained the problem perfectly. I agree 100% with you. I have noticed that on copiers where the toner is not original the roller can be damaged after just 20,000 copies. Sticky Your comment below the video. Respect.
Thank You Check out my gadget store 🤩🥳 MOVIE STUDIO SHOP: my-store-7469644.creator-spring.com/ 🔥🔥 TH-cam SUPPORT: th-cam.com/channels/OHtXTtGHj33pUm8Gf2FH3A.htmljoin 😁😆 PATREON: www.patreon.com/CopyExpertMovieStudio 🔥💥 PATRONITE: www.patronite.pl/1796
En estas fotocopiadoras, los termistores muy a menudo necesitan ser reemplazados por otros nuevos o debe eliminarse la suciedad de sus superficies. De lo contrario, el rodillo de presión se destruirá rápidamente. Start subscribing to my channel - it helps to develop my content.
Yes. You are a highly qualified specialist. This is Fuser ricoh MPC5503 exactly this series of copiers. Exactly 5503 and 4503, i.e. an additional rack that controls the lamp cover. If you give me your shipping address, I will send you a small gift. You can send the address if you want to my e-mail: copy-expert@wp.pl
@Maxim Ibragimov wrote an excellent comment: "One of the common causes of toner adhesion to a thermistor is the use of compatible toner. Due to a low or high temperature, the toner begins to stick to the thermal film / Teflon roll, and from it goes to the thermistor. Or, part of the toner (particles) that are not baked, parrying in the air, settle on the thermistor. On the original toner, this can also be observed, but its amount is not critical to affect the part, because by this time the unit will use up its resource. The cause of this problem is not the only one, but compatible toner is in principle a common cause, the problems of which appear during the operation of the machine."
THANK YOU @Maxim Ibragimov
Good video and I watched the whole video, I did not see you inspect, service or replace the Thermistors that caused the damage. what do you use to clean Thermisteors without "killing" them?
I usually replace these elements with new ones. Usually cleaning works for a short time, and I don't like the risk.
Check out my gadget store 🤩🥳 MOVIE STUDIO SHOP: my-store-7469644.creator-spring.com/
🔥🔥 TH-cam SUPPORT: th-cam.com/channels/OHtXTtGHj33pUm8Gf2FH3A.htmljoin
😁😆 PATREON: www.patreon.com/CopyExpertMovieStudio
🔥💥 PATRONITE: www.patronite.pl/1796
Merci beaucoup
Bon travail 👍👍👍👍👍
Thank You !!!!
In that case, the thermistor was not damaged, causing damage to the pressure roller?
It's not in the video, but I only cleaned the thermistor. Some toner has built up on the thermistor and it has hardened and damaged the roller. It was enough to touch the thermistor with a finger and the toner fell off. Everything is still working normally. Only the question arises: why is there this problem with the toner build-up on the thermistor in this model of copiers?
@Maxim Ibragimov You explained the problem perfectly. I agree 100% with you. I have noticed that on copiers where the toner is not original the roller can be damaged after just 20,000 copies. Sticky Your comment below the video. Respect.
Thanks
👍👍👍👍
Thank You
Check out my gadget store 🤩🥳 MOVIE STUDIO SHOP: my-store-7469644.creator-spring.com/
🔥🔥 TH-cam SUPPORT: th-cam.com/channels/OHtXTtGHj33pUm8Gf2FH3A.htmljoin
😁😆 PATREON: www.patreon.com/CopyExpertMovieStudio
🔥💥 PATRONITE: www.patronite.pl/1796
I would like to see more videos detailing the replacement of the fuser film and lubricating the film if possible
I plan to record a detailed film about the replacement of the foil, it's raining oil and new oil.
Que lástima que no reemplazaste la película térmica, solo cambiaste la unidad completa con la película térmica ya montada
En mis otros videos hay procedimientos en los que solo reemplazo la lámina y la almohadilla de aceite. Entra en mi canal MP2554
Muy bueno el video. Solo que no se muestran como están los termistores y como limpiarlos, los cuales marcaron el rodillo de presión...
En estas fotocopiadoras, los termistores muy a menudo necesitan ser reemplazados por otros nuevos o debe eliminarse la suciedad de sus superficies. De lo contrario, el rodillo de presión se destruirá rápidamente.
Start subscribing to my channel - it helps to develop my content.
Hola Tomasz Jemiołek no fui el primer comentario¡¡ >:3 , encantado de conocer tu canal, ¿te gustaria ser parte de mi comunidad?,
Hi. What kind of community do you mean?
Disesño complicado no anti para distraídos
Lo escribiste bien :)
a servis of images of ricoh mpc 3003 3503 4503 6003
Yes. You are a highly qualified specialist. This is Fuser ricoh MPC5503 exactly this series of copiers. Exactly 5503 and 4503, i.e. an additional rack that controls the lamp cover. If you give me your shipping address, I will send you a small gift. You can send the address if you want to my e-mail: copy-expert@wp.pl
Traduce al español hermano
Hice subtítulos en 38 idiomas. También hay subtítulos en español.
@@MrRicoh pense que el video mismo podias hacer en español ,
Es imposible.