You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
2011 Whirlpool Duet: WFW 9150 WW 02, Front Loader, Made in Mexico.O.k., I see that if I click on the down arrow after the title I get more information. It would also be helpful it mention the failure symptoms in the video.Q. Are there other problems associated with a pressure switch failure?I started out this morning with poor drainage and a tub full of wet clothes. I cleaned 1/2 pound of lint plus other "things" out of the pump filter. I only got paid three dimes and a safety pin for my effort. Now the pump works fine. The tub has overfilled twice. Who know how far it would go. I hit the ON/Off switch at about the half full mark and the pump starts and empties the tub quickly. I restart in the Rinse/Drain Spin mode but it will not spin.If started on the Normal setting it seems to function fine for a while then stops, Rinse light comes on with intermittent "Beep". Then after moments of science the tub will turn a bit, stop a bit... Mostly stop.
My whirlpool duet steam direct drive has this pressure switch, but I didn't see a screw to adjust the water level like the pressure switch on older front load whirlpool duets. Is there a way to force the washer to fill with more water?
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
The repair clinic doesn't tell you how to test the switch. Because my maytag does the f01 e03 failure all the time so I constantly have to check the filter catch at the bottom of the pump. So when are those idiots at maytag going to get rid of this annoying switch and make the pump filter trap not sutch a pain To clean. It's the number one error codes this model has.
Remove the black hose as it's filling and it will fill up as long as the hose is removed. So look on the bottom of the pressure switch and you will see a tiny hole. You can increase the water level 2 ways. Increase the hole diameter or put an inline splice with a bigger hose on the end maybe as much as a foot long (you will need to play with the length but it must be bigger). The point is to lower the pressure trigger point at which turns the switch off.
![BABYMONSTER - 'DRIP' M/V REACTION [WAS NOT EXPECTING THIS!!!]](http://i.ytimg.com/vi/t0Lpgr1jo3Y/mqdefault.jpg)
Ridiculously easy! Thank you. And the part is inexpensive.
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Thank you, very clear and to the point. It's an easy repair.
What way did you try
2011 Whirlpool Duet: WFW 9150 WW 02, Front Loader, Made in Mexico.O.k., I see that if I click on the down arrow after the title I get more information. It would also be helpful it mention the failure symptoms in the video.Q. Are there other problems associated with a pressure switch failure?I started out this morning with poor drainage and a tub full of wet clothes. I cleaned 1/2 pound of lint plus other "things" out of the pump filter. I only got paid three dimes and a safety pin for my effort. Now the pump works fine. The tub has overfilled twice. Who know how far it would go. I hit the ON/Off switch at about the half full mark and the pump starts and empties the tub quickly. I restart in the Rinse/Drain Spin mode but it will not spin.If started on the Normal setting it seems to function fine for a while then stops, Rinse light comes on with intermittent "Beep". Then after moments of science the tub will turn a bit, stop a bit... Mostly stop.
This fixed my Maytag washer..
My whirlpool duet steam direct drive has this pressure switch, but I
didn't see a screw to adjust the water level like the pressure switch on
older front load whirlpool duets. Is there a way to force the
washer to fill with more water?
I have the same question. If not, anyone know a suitable replacement?
Did you figure it out? Having the same problem.
Thank you very much
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
The repair clinic doesn't tell you how to test the switch. Because my maytag does the f01 e03 failure all the time so I constantly have to check the filter catch at the bottom of the pump. So when are those idiots at maytag going to get rid of this annoying switch and make the pump filter trap not sutch a pain To clean. It's the number one error codes this model has.
What are the symptoms of a bad pressure switch?
E01 F03 error code
Remove the black hose as it's filling and it will fill up as long as the hose is removed. So look on the bottom of the pressure switch and you will see a tiny hole. You can increase the water level 2 ways. Increase the hole diameter or put an inline splice with a bigger hose on the end maybe as much as a foot long (you will need to play with the length but it must be bigger). The point is to lower the pressure trigger point at which turns the switch off.
What do you mean by increase hole diameter what hole?
Tom Mills do you have a video of this by any chance?
explain how much piece of hose did you use? it just runs and runs when i tried to add hose.
i did all of these two things and wasted time and money
@@tonymemory2279 did you figure it out I'm also trying to increase the water level on my whirlpool
Did you guys see the flourish when they showed the new part, dang.
how do you adjust for more water?
Did you ever figure it out?
Wish they would show the symptoms.
Thank you.
Hola
F20