A tip on placing nubs in. Flip the hop unit upside down so the nub window is facing the floor, and the arm is swinging at the ground. Put the nub directly in the teeth on the arm that hold the nub. "Swing" the arm into the upside hop unit and it's place correctly each time. Easier then tryna use a tool to correctly put the nub in the window where you THINK the arm will land.
@@future_phonk np mate , forged is more expensive but not so good in terms of airsoft quality ( loose body compared to cheaper version). Overal MTW is beast
Awesome video mate. Can't wait to get mine. Really like what you did with the supressor and magpul stock! Be interested to see how it compares too the old one
If you're having trouble getting the barrel nut off the receiver, they make an armorers wrench and a plastic block the receiver goes in. You mount the received in a vice and break the nut off with the specific wrench. If it's RS spec, you chould be able to to get both for ~50$
if your running the 13ci tank on your reg with the MTW get yourself an aero stock mate, I love mine on my 10" billet with reaper engine I get 1200-1300 shots I just change it at lunch, and with all the bushes you go crawling through getting rid of the line would probably be a bonus for you I got a similar setup to yours only one size up 10" barrel with 13" rail, novritsch modular suppressor and aero stock
Ran into issues with mine on Sunday....Groupings were all over the place. Running ZCI 6.02mm barrel with G&G Green & Flat nub. Going to try 6.01mm & Maple Leaf Silicon 60D Bucking & Omega nub this Sunday and see how it goes. If still causing issues, will try original barrel and go through each bucking again.. :)
Well seems to better. About 3000bbs I went through. 0.36 on semi playing on he sites DMR power lvl. Not bad at all...not many flyers, Going to try 0.28 or 0.3 as full auto next time and see how it copes. Still get a fps spike though...not very consistent in the fps. EDIT... I was also testing between games...firing a lot of rounds to bed the bucking in. I wouldn't get through 3000 bbs playing as DMR normally...maybe 2999..lol
@@maxsteele20 yeah, the problem was probably the bucking and nub set, the maple leaf combo should be amazing, have a friend who runs it and prefers it over rhop, and it’s what I’m switching to in my p*
Hey if you do put plumbers tape just run a small amount halfway over the bucking and barrel just enough to wrap around once that is all you'll ever need if even needed. I see people just load the hop up and barrel instead because of wobble or what have you. Now a small brass barrel washer with a rubber o-ring solves that issues.
also a easy way to stabilize your inner barrle perfect is put very small rubber orings over the inner and press them betwen the inner and outer. you can do it after you put in back your barrle if it looks out like yours. greez from germany
What is the outer diameter of the suppressor you used, I'm trying to determine what suppressor to buy so that it will actually fit inside and be hidden by the Invictus Rail
Looking forward to part two. I think that last clip with the exfil box was where I dispatched about 8 of you and got shot one of them in the dinkle lol (I did apologise) haha.
What is the diameter for the silencer you used? how long is it? I really love your setup and would like to do the same for the silencer...also if you could let me know the diameter of the hand gard from wolverine.
I'm just wondering why a 6.05mm barrel..... would a 6.01 not make it more air efficient and use less pressure. Most of my upgrading barrel wise have been 6.01.
I bet you has a bit of a surprise when you put an airline on and pulled the trigger and nothing happened. You forgot to reconnect the white electrical plug at the back of the engine. LOL! Looks like a nice rifle! I need to install a G&G Green bucking on my F2 MK18 build. I had it out last weekend and the bucking was having a hard time in the cold temps we had that day. High of 36 degrees F, The G&G Green is cold resistant.
That's interesting that you got a G&G green with yours from factory. I also got a 2021 model MTW and mine came with a Maple Leaf Macaron bucking. How have you found the G&G green? I have a fresh one and I've been tempted to put it in there :)
Keep the maple leaf dude. Me and my friend have messed around with them both on our setups and found ML had better consistency range and groupings over the g&g green.. hope that helps man
@@JasonFolk07 For some reason I couldn't get a G&G green to feed anyway. I've stuck with the Maple Leaf and have had no issues outperforming other guns on the field :)
Also I am wondering why the g&g green bucking I personally would run a s-hop "easy" or r-hop "difficult" then a Prometheus flat purple bucking with a 6:05 will by far over shoot any setup on the market personally that's been my setup three replicas now and I have had the best consistency and groupings and with the correct joules and bb weight you can wipe the field of other players.
@@CammanExtra sorry to be a pain newbie here and don't want to fk up lol, but it's the only video that has done what I want to do... What sizer was the inner barrel I guess they are in mm? And is that grip line 5 or 10inch?
It’s my first HPA gun My came semi locked and I can’t seem to get it out of semi to full auto even tired changing the fire modes from the manual, have you or anyone else had this and knows how to change it. Much appreciated
A tip on placing nubs in. Flip the hop unit upside down so the nub window is facing the floor, and the arm is swinging at the ground. Put the nub directly in the teeth on the arm that hold the nub. "Swing" the arm into the upside hop unit and it's place correctly each time. Easier then tryna use a tool to correctly put the nub in the window where you THINK the arm will land.
Anyone else notice how he didn’t plug the engine back into the adapter to connect to the trigger board?
Rumor has it
It's still unplugged
I love how easy this is to maintain and upgrade. Definitely picking up a forge series.
do not get forge version, its made like the real one so u will get a lot of woble and loose parts in body.
@@maciejxxx4059 thanks for the insight!
@@future_phonk np mate , forged is more expensive but not so good in terms of airsoft quality ( loose body compared to cheaper version). Overal MTW is beast
Awesome video mate. Can't wait to get mine. Really like what you did with the supressor and magpul stock! Be interested to see how it compares too the old one
Set the selector switch in semi to put your line trough. Then you have more space.
Thanks for the tip. 👍
Legend
If you're having trouble getting the barrel nut off the receiver, they make an armorers wrench and a plastic block the receiver goes in. You mount the received in a vice and break the nut off with the specific wrench.
If it's RS spec, you chould be able to to get both for ~50$
What size is the suppressor? As im looking for one to fit inside my rail
if your running the 13ci tank on your reg with the MTW get yourself an aero stock mate, I love mine on my 10" billet with reaper engine I get 1200-1300 shots I just change it at lunch, and with all the bushes you go crawling through getting rid of the line would probably be a bonus for you
I got a similar setup to yours only one size up 10" barrel with 13" rail, novritsch modular suppressor and aero stock
Ran into issues with mine on Sunday....Groupings were all over the place. Running ZCI 6.02mm barrel with G&G Green & Flat nub. Going to try 6.01mm & Maple Leaf Silicon 60D Bucking & Omega nub this Sunday and see how it goes. If still causing issues, will try original barrel and go through each bucking again.. :)
Well seems to better. About 3000bbs I went through. 0.36 on semi playing on he sites DMR power lvl. Not bad at all...not many flyers, Going to try 0.28 or 0.3 as full auto next time and see how it copes. Still get a fps spike though...not very consistent in the fps. EDIT... I was also testing between games...firing a lot of rounds to bed the bucking in. I wouldn't get through 3000 bbs playing as DMR normally...maybe 2999..lol
@@maxsteele20 yeah, the problem was probably the bucking and nub set, the maple leaf combo should be amazing, have a friend who runs it and prefers it over rhop, and it’s what I’m switching to in my p*
Just ordered mine can't wait mate
Great review man really enjoyed it
Hey if you do put plumbers tape just run a small amount halfway over the bucking and barrel just enough to wrap around once that is all you'll ever need if even needed. I see people just load the hop up and barrel instead because of wobble or what have you. Now a small brass barrel washer with a rubber o-ring solves that issues.
also a easy way to stabilize your inner barrle perfect is put very small rubber orings over the inner and press them betwen the inner and outer. you can do it after you put in back your barrle if it looks out like yours. greez from germany
What is the outer diameter of the suppressor you used, I'm trying to determine what suppressor to buy so that it will actually fit inside and be hidden by the Invictus Rail
With the barrel nut if its tight like mine was just smack it with a hammer to loosen.
You ever R-hop this or just leave it with stock unit & a good bucking?
Looking forward to part two. I think that last clip with the exfil box was where I dispatched about 8 of you and got shot one of them in the dinkle lol (I did apologise) haha.
Wow didn't know you have an extra channel nicely done video as always!
Hey which silencer and inserts do u prefer for the MTW?
Cant find the filtered grip lines anywhere, like wtf does MTW not make them anymore?
You know, now when this ”spit on that thing” is goin very popular your threatment with hop up rubber 🤣🤣🤣
I do wonder how long he was sitting there wondering why it was not shooting, before he realised the engine was not plugged in.
What is the diameter for the silencer you used? how long is it? I really love your setup and would like to do the same for the silencer...also if you could let me know the diameter of the hand gard from wolverine.
Idk prob 28-35 mm
orrange flashhider in the BIN!
Great video cant wait for my pre order to arrive! Could you please do a list for the parts used?
Is there any accessory for the receiver of this gun😅
I'm just wondering why a 6.05mm barrel..... would a 6.01 not make it more air efficient and use less pressure. Most of my upgrading barrel wise have been 6.01.
I bet you has a bit of a surprise when you put an airline on and pulled the trigger and nothing happened.
You forgot to reconnect the white electrical plug at the back of the engine. LOL!
Looks like a nice rifle!
I need to install a G&G Green bucking on my F2 MK18 build. I had it out last weekend and the bucking was having a hard time in the cold temps we had that day. High of 36 degrees F, The G&G Green is cold resistant.
I want to mention that too, the control board is not connected lol... which leads to the 7.4v battery not working...
@Camman Extra
does he like only the mtw barrels? or I can fit whatever I want?
Any
That's interesting that you got a G&G green with yours from factory. I also got a 2021 model MTW and mine came with a Maple Leaf Macaron bucking. How have you found the G&G green? I have a fresh one and I've been tempted to put it in there :)
Keep the maple leaf dude. Me and my friend have messed around with them both on our setups and found ML had better consistency range and groupings over the g&g green.. hope that helps man
@@JasonFolk07 For some reason I couldn't get a G&G green to feed anyway. I've stuck with the Maple Leaf and have had no issues outperforming other guns on the field :)
That’s awesome I got one just a month ago and mine had a maple leaf macaron 60 degree bucking. All I did to mine was a nub and barrel swap.
Do you also use this setup when you play it as dmr?
Anyone know what charger I need or maybe a link to one?
Also I am wondering why the g&g green bucking I personally would run a s-hop "easy" or r-hop "difficult" then a Prometheus flat purple bucking with a 6:05 will by far over shoot any setup on the market personally that's been my setup three replicas now and I have had the best consistency and groupings and with the correct joules and bb weight you can wipe the field of other players.
Have you brought the phoenix hop unit as im having problems getting mine to work camman?
amazing!! where did you get your mtw? plammimg to get one
Could you remove the outerbarrel with the innerbarrel etc in it??? Or is it better to remove it all?
Nice vid, which suppressor did you use please
I use a modified Silverback Mk23 suppressor
@@CammanExtraWhy You modified their supressor?
Is the stock a mil spec version or a commercial version?
What is a filtered grip line?
The nub for hop unit is soft rubbery or hard plastic ?
My mtw came with maple leaf macron 70
Hi, I'm guessing that's a 10" Mtw? What size outer and inner barrel did you get, so the suppressor stayed like that? Thanks
7"
@@CammanExtra sorry to be a pain newbie here and don't want to fk up lol, but it's the only video that has done what I want to do... What sizer was the inner barrel I guess they are in mm? And is that grip line 5 or 10inch?
Is this the length you’re using in your ghillie videos?
Yes it is
It’s my first HPA gun My came semi locked and I can’t seem to get it out of semi to full auto even tired changing the fire modes from the manual, have you or anyone else had this and knows how to change it. Much appreciated
Some markets do not allow full auto. Like Germany
Hi there, do you (or anyone in the comments) have any tips for setting dwell on the billet?
Follow the recommended guide on Wolverine website.
You forgot to connect the cable to the engine. 100% it didn‘t work after reassembly 😉
Please get a Magpul grip to finish the great look. =) ...For the price of the MTW, the filter line should be standard
‘Son of a Bitch’ made me laugh out loud!
Is that 10" outer barrel up for grabs 🙊
You forgot the plug for the engine on the rear clip
Yeah, I know. I was scratching my head when I can to test fire it. 😂
@@CammanExtra I just had my first game with my forged series this Sunday just gone I am really liking it
Camman, That is a damn, fine sexy-looking piece. Has the accuracy changed much after the barrel change? Is this one designated for sniping?
Hi !!! ;)
Where did you buy the latest one billets ?
Can be bought direct from Wolverine, PowAir, High Pressure Airsoft.
@@CammanExtra Thanks Camman, you convinced me to buy one ;)
What banana is that? Can you post a link? Great video like always!
Hello
What suppressor you have put onn
Wess
Custom Silverback Mk23 Suppressor
@@CammanExtra thnx
was ur stock also wobbling ? i got mine today and my G&G had a way better stock :D
What bb weight and fps do you use ?
0.4g Geoffs
noice 🔥👍
I bought one 🙏🏾🤗
I want one😍
What nice
you need a bigger table bro
Walker Jason Lewis Robert Taylor David
WTF IS A CENTIMETER!!! RAAAAAAAAAAAAAAAAAAAAA!!!! IMPERIAL!!!! MURICA!!!
👍
Thanks for the video, nice to see it's easy to take apart before I buy one.
👏👏👏😍😍😍
Ly thing I don't care for is there handguard it's super but ugly
Moist
You could have better upgrades to be honest, g&g green 🤢🤮
Nothing wrong with a G&G green. They've been good for about 10 years. If it aint broke, don't fix it.
It works wonders in the MTW, especially when combined with the Silent Industries 1.0 arm.