Triumphy Trophy Starter Clutch Repair

Roger Lovelock from BB BikeShop, repairing a starter clutch on a 1992 Triumph Trophy.
Website: www.bbbikeshop.co.uk
Filmed and Editied by: Roger Lovelock
Edited by: Hugo Beanland

[@jeremyrussell9270]

Great video, very clear and concise. Disappointed with Triumph for not making the replacement directly compatible.
Great job many thanks
Jeremy Russell

[@mchabi18]

Lots of tricky stuff to care about. Great tutorial thank you.

[@gordonturke4171]

Thanks for sharing this on how to do the spray clutch.

[@andilock8276]

Cheers! Really, really informative!

[@BS-vm3pk]

very helpfull video ,thanx

[@xaviert.a.2435]

thank you for the lesson ,i own one trophy 1200 year 1994 52000 km it go perfect.

[@TheFormat1234]

My old trident is at 56k on original sprag - not looking forward to doing this. But thanks for posting video: it's going to be a godsend when the day comes.

[@terryaylward8178]

You were lucky the collar didn’t drop in the sump! There is another video of the same procedure but taking precautions to avoid that😀👍

[@specialandroid1603]

1994 sprint with no sprag clutch plate - keep mine charged all the time so only starts on full battery - splitting the engine casing would be my worst nightmare.

[@vikingcsm]

Really helpful... not as simple as on a Yamaha.

[@GregKerchhoff]

Great video.I think mine needs replacing. I asked the mechanic what was involved and his explanation lost me after a minute. How many hours work is this, starting and finishing with a road ready bike?

[@kevkingsnorth9222]

excellent video

[@bostedsprocket6708]

ive got a 95 sprint, 45k original sprag no access plate, so I'm dreading it but ive been told if you keep the battery topped up it should never be a problem??

[@kevinansell9341]

I find it incredible that a Manufacturer supplies a Modified part where you need to remove material from the Crankcase to get it to fit...

[@marcoalessandro2034]

i think it is a 'fix' or improvement from the OEM part

[@richardrichard5409]

And the improved part fails too

[@Eric-nb7vg]

sprag clutch speed triple 2006. hello. do you know where in the uk can i get the parts to fix this. on the cheap side of course. a new kit is around 300.

[@trondwell13]

I heard it was advisable to push a new spline through to avoid any possibility of dropping washers....

[@olboymotoaustralia4294]

You were very lucky that spacer never bounced off the gears and toddled off down into the bottom of the case. Could have cost you a lot more time trying to fish it out. May have turned into an engine split quite easily. Well done though & thanks for the video upload. 🙏🏽

[@860240]

Thanks, just going out to the garage to do mine for the second time ! in 49,000 miles, by the way are you from Radstock ? it sounds like it.

[@DriverwolfRacing]

I'm from Marlborough in Wiltshire.

[@libertyman3072]

👍💪👍💪👍💪👍💪👍💪👍💪👍💪👍💪

[@Richard-ts6mg]

I have a 92 trophy 900 with the same problem as you had. Haynes manual puts this job as difficult, im not sure if i could do it.
Im interested to know, how long did it take you to do the job ?

[@bbbikeshop8359]

It took about 3 hours, but the customer had already removed tank, coils and carbs.

[@jimtrotter2084]

I had to drop my eng and split the case to replace the starter sprag

[@outspoken5326]

I had to split the case on my bike to replace the starter sprag. That is what's its called not starter clutch.

[@attilapal8490]

900ccm??? 3cylinder???

[@jimtrotter2084]

your lucky you have the plate.