Modifying Flysky transmitter with rechargeable battery
ฝัง
- เผยแพร่เมื่อ 21 ก.ย. 2018
- My rc video playlist
👉 • Rc video playlist
Today in this video I've shown how to use a rechargeable li-ion 2s 7.2V battery to your rc transmitter. - วิทยาศาสตร์และเทคโนโลยี
![ตีสิบเดย์ [FULL] | ครอบครัวสะท้านทุ่ง "นางบี & อ้ายสติ๊ก"](http://i.ytimg.com/vi/A1rhYcxxNtA/mqdefault.jpg)
Much easier and neater to use 4 rechargeble enerloops cells!
Boa ideia !👏👐
To run a 2s lipo/ li-ion pack you have to check the voltage regulators in the flysky fsi6/X. Some regulator can only handle up to 7v before overheating and burning out. A heat sink can prevent this but it is better to change out the voltage regulators with better ones.
FSi6 can handle upto 8.4 volts
@@Saifbak16 please....are you sure about it?
@@Douglas-hj3fe Yes brother I am 100% sure. I have been using it on 8.4volts for a long time. It works fine
@@Saifbak16 tanks Man ...i'll try It Just tomorrow ...and lets see If fly It or If fry It lol.
Your music is very nice!!!!!
All parts of the circuit of the fs i6 works with 3,3v from single regulator. The beast modification for this is with 3,7v batery, but needs to change the firmware to change low voltage alarme.
Good 👍
Can I put instant a lipo 2s on it it’s 7,4 v ?????
A 1N4007 in series with the 7805 GND pin could have made the 7805 output 5.6 to 5.7 volts which would be more suitable then the common GND becomes the cathode of the diode..
Yes, you are absolutely right.
Thank you
You are welcome! Actually 2 Diodes = VERY Fresh 4 AA batteries. AA When Very new and Freshly made = 1.6V x 4 = 6.4V for maximum signal but if you are unsure add a different diode type with the 4007
what are the capacitors for?
Good i idea
Plz tell me the volt of the li-ion battery
A what a hack job. :)
your transmitter power is a perfect way to establish. Very careful on doing it. in this way will not get alarm beeb. and 5v get heat up and unwanted wastage of battery.... having this setup in outside is dangerous while flying... Also Never try with usb bank even. you may get sudden power drop. so finaly I can recommend the best way is using rechargeable battery. it will not give sudden power death. use Panasonic eneloop...varta....1800-3000ma NIMH battery. specially use Low dischange rate battery. I charge the battery normally after my 5-6 flying. If you not using for even 6 month no discharge. So no need to charge.
Totally agree.
Do NiMH batteries work well with this radio? 4 NiMH batteries should give only 4.8V
@@ramon2190 I use NiMH on my flysky i6x
And I don't have any problems. It won't show battery full charge but they work and also have low battery alarm.
What' song ?
hi great video thanks for sharing.
do you get any low voltage warning. İn some other videos there are comments like there is no low voltage warning transmitter suddenly stop etc.. thank you very much.
Yes, occasionally i get warning too
song name please?
looks like it's at only 5.06 V out of 6v for the AA batteries...looks like you are running this transmitter at low-voltage, thus damaging it.?? no? and so why don't you have a LIPO that can fit in the battery compartment then never again needing to replace the battery? how can we do this together
Pls tell us the polarity of capacitors connecting to 7805
All negative side goes to middle pin
Can i change battery 3s 2200 11.1v?
Then the ic will get little more hot
In my city, I can't find 100uf 10v capacitors. Can i use 100uf 25v? Thanks for the video, it is very useful.
100uf 25v will work without any problem
@@TechIdeasAG Thank you for your answer
No heatsink for the 7805? 🔥 🔥 too hot 👎🏻
As the current consumption is less than 130mA it rarely gets hot