There are 4 screws that can be accessed from the back to remove the LCD plinth from the front of the keyboard without removing the button PCB or the keyboard. The 2 square cutouts on the back panel give you access. Need a long magnetic screwdriver.
Note thank you for your video The Korg I3 opens on a hinge from the front . You remove the screws with the star lock washers . There are 3 on the left side 4 on the right and 5 along the rear hinge line . Do not remove the non lock screws they hold the circuit boards and the key bed .” Important “. On the joy stick side on the rear there is an access hole look and you will see a deep screw remove it . Next on the 3.5 drive side you have to remove the only non lock screws you’ll remove and take the lower trim Panel for the drive off . Then carefully flip the keyboard over with a hand flat on the back . DO NOT LIFT FROM THE SIDES. Then when flipped over , lift from the sides . Everything is easy access . Note 2 the display removes with two screws one is clearly visible the other is though an access hole though the switch board located in the upper hinges panel . Hope this helps . So much easier . PS I replaced my display works great Thanks for the help
Good video. You have a good strategy for staying organized with all the screws during the dissassembly process. Regarding the lcd: are you sure you have to replace your middle ic controller? It is more likely that once you have taken the lcd apart, the "zebra' strips which connect the lcd glass to the circuit board aren't connectiing properly to the lcd circuit board gold contacts or the lcd glass.
haven't replace the middel IC yet. but thank u for ur advise,I will try to align pcb contact first. My first tought was no picture in the middle square that supposed to be handle by middle IC controller. I hope I was wrong, big effort to replace the IC :) thank u .
Ive worked on about 100 keyboards in my day, this is one of the worst ever to take apart and then put back together. Took over 5 hours to take apart, then replaced about 12 switches, and glued 3 plastic buttons. The buttons on this thing are a very bad design. I used some glue called Zap-A-Gap and it seemed to work well, I doubt many other glues would work on this cheesy hard plastic. I replaced the El backlight by clipping the leads to the old one, and slid the new one over it. However, it took 7 hours to reassemble the I3 and upon completion, the I3 was fixed perfectly, EXCEPT FOR THE BACKLIGHT. Im very disappointed! So either my solder joint was bad, the thing powering the backlight was out, or the backlight I got from HongKong was shit. I will not spend another 13 hours trying to get the backlight to work. I guess a little velcro and a nightlight will have to do. :( update: well I just figured out I put the el backlight in upside down! Would have been nice if the ebay seller would have included instructions! DAMN!
I have a Roland G 1000 and it is developing a problem with the LCD display in that the colour is fading from blue to a yellow brown and can hardly read it, it is strange that if I lean back I can see that the writing looks normal but leaning forward when I want to edit it looks pale I can hardly make it out, maybe it is only the light or something more serious, I have searched everywhere for a part, part no, ROHM RCM6018 upon looking around to try to find a part for it or maybe a generic brand Roland Corporation were of no help. Do you think that if the light goes out the keyboard would be totally unusable? hoping my request is not too much trouble await your reply Kind regards Noeline
can anyone guide me how to set or on chords mode. It does played when I start beat but when I want to play without beat simply chords in church it does sounds the selected tone. Please guide how can I play chords without beat how to set it's setting ?
You didn't have to take the lcd apart if there was nothing wrong with the text. You risk damage to the lcd when you do that. You could just desolder, clip, and insulate the old leads and then slide the new backlight over top of it and solder the new leads to the old lcd pads.
Thanks for sharing. My PA800 KORG arranger LCD contrast/brightness oscillates from dim to normal, back and forth, for as long as the keyboard is on. The oscillation frequency is about 2 seconds per cycle. Any ideas?
hi, I am repairing the screen of the KORG I3 and I have removed the battery, so I have lost all memory. can you help me recover the softwear? thank you. i have not floppy.
i found it on ebay.com : EL backlight. but for G600 I believe it is using small LED light from side , maybe some of them died. and check for polarzed film , it is fading along years
Hello .... I have a korg i3 and I want to register a new style ... but I found it difficult .. Can you please guide me to download a video with a detailed explanation of how it works Please😖💕💕💕💕
my display screen comes line, its continue like ur display after placed backlight.so I m not findout the problem pls help to how can restored my display again new
mas Addie.. mohon info.. KORG Trinity saya polarizer nya sudah worn off... apa bisa di tempel lembar polarizer dari luar saja? sekarang layarnya cuma kelihatan backlight, tapi kalo pake kacamata polarized masih bisa kelihatan tulisan nya.. terima kasih banyak buat info nya..
polarizer ada 3 macam setahu saya 0 , 45, 90 derajat untuk posisi paling jelas harus di test polarizernya diputar2, masalah di depan atau belakang bisa saja tapi lapisan lemnya ada di mana waktu beli. bawah atau atas.
@@addiengr1 betul sekali mas, kalo pake kacamata di rotate 90 drajat baru jelas tulisan nya.. masalah nya saya mau bongkar dan lepas polarizer nya dari dalam ga berani.. (keyboard nya masih kayak baru krn cuma disimpan di hardcase, cuma masalah di polarizer ini saja) apa ada info dimana saya bisa dapet polarizer untuk di tempel di luar touch screen nya saja hanya supaya bisa liat info layar nya? sekali lagi terima kasih banyak buat respon dan info nya... appreciate it..
@@papankunci bisa beli polirezer film punya screen laptop atau monitor PC, saya potong sesuai kebutuhan. kalo polarizer aslinya korg mungkin sudah gak ada atau harus pesan ke luar.
@@addiengr1 terima kasih buat info nya mas Addie... baik coba saya cari2 yg bisa buat experiment di tempel dari luar dulu... ga keliatan bagus ga apa2 asal bisa baca tulisan nya saja... sukses selalu ya mas...sekali lagi terima kasih banyak..
iya sebagian ada yg pakai layar LCD dot matrix. tidak pakai backlight. cek awal koneksi solderan tua yg korosi atau sambungan semua kabel. kerusakannya bgmn
There are 4 screws that can be accessed from the back to remove the LCD plinth from the front of the keyboard without removing the button PCB or the keyboard. The 2 square cutouts on the back panel give you access. Need a long magnetic screwdriver.
very helpful as my lithium battery was dead I had the confidence to change it after watching this video thanks and it's working.
Note thank you for your video
The Korg I3 opens on a hinge from the front . You remove the screws with the star lock washers . There are 3 on the left side 4 on the right and 5 along the rear hinge line . Do not remove the non lock screws they hold the circuit boards and the key bed .” Important “. On the joy stick side on the rear there is an access hole look and you will see a deep screw remove it . Next on the 3.5 drive side you have to remove the only non lock screws you’ll remove and take the lower trim Panel for the drive off . Then carefully flip the keyboard over with a hand flat on the back . DO NOT LIFT FROM THE SIDES. Then when flipped over , lift from the sides . Everything is easy access . Note 2 the display removes with two screws one is clearly visible the other is though an access hole though the switch board located in the upper hinges panel .
Hope this helps . So much easier .
PS I replaced my display works great
Thanks for the help
Fantastic your knowledge is outstanding! I am about to buy a Korg Triton LE 61 which has a faulty screen for a very low price:)
Good video. You have a good strategy for staying organized with all the screws during the dissassembly process. Regarding the lcd: are you sure you have to replace your middle ic controller? It is more likely that once you have taken the lcd apart, the "zebra' strips which connect the lcd glass to the circuit board aren't connectiing properly to the lcd circuit board gold contacts or the lcd glass.
haven't replace the middel IC yet. but thank u for ur advise,I will try to align pcb contact first.
My first tought was no picture in the middle square that supposed to be handle by middle IC controller.
I hope I was wrong, big effort to replace the IC :) thank u .
Ive worked on about 100 keyboards in my day, this is one of the worst ever to take apart and then put back together. Took over 5 hours to take apart, then replaced about 12 switches, and glued 3 plastic buttons. The buttons on this thing are a very bad design. I used some glue called Zap-A-Gap and it seemed to work well, I doubt many other glues would work on this cheesy hard plastic. I replaced the El backlight by clipping the leads to the old one, and slid the new one over it. However, it took 7 hours to reassemble the I3 and upon completion, the I3 was fixed perfectly, EXCEPT FOR THE BACKLIGHT. Im very disappointed! So either my solder joint was bad, the thing powering the backlight was out, or the backlight I got from HongKong was shit. I will not spend another 13 hours trying to get the backlight to work. I guess a little velcro and a nightlight will have to do. :(
update: well I just figured out I put the el backlight in upside down! Would have been nice if the ebay seller would have included instructions! DAMN!
I have a Roland G 1000 and it is developing a problem with the LCD display in that the colour is fading from blue to a yellow brown and can hardly read it, it is strange that if I lean back I can see that the writing looks normal but leaning forward when I want to edit it looks pale I can hardly make it out, maybe it is only the light or something more serious, I have searched everywhere for a part, part no, ROHM RCM6018 upon looking around to try to find a part for it or maybe a generic brand Roland Corporation were of no help. Do you think that if the light goes out the keyboard would be totally unusable? hoping my request is not too much trouble await your reply Kind regards Noeline
can anyone guide me how to set or on chords mode. It does played when I start beat but when I want to play without beat simply chords in church it does sounds the selected tone. Please guide how can I play chords without beat how to set it's setting ?
You didn't have to take the lcd apart if there was nothing wrong with the text. You risk damage to the lcd when you do that. You could just desolder, clip, and insulate the old leads and then slide the new backlight over top of it and solder the new leads to the old lcd pads.
thanks, Maybe I'm just lucky.
yes it is possible to slide..
Thanks for sharing.
My PA800 KORG arranger LCD contrast/brightness oscillates
from dim to normal, back and forth, for as long as the keyboard is on. The
oscillation frequency is about 2 seconds per cycle. Any ideas?
nice share guy, maturnuwun
Very good work, very good video :)
Mantaap...🖒 sangat bermanfaat..Maaf klu boleh shere no contc sob, kebetulan keyboard i3 layar mati.. thx
Where can I buy the electroiluminecence foil for korg triton le model
Triton Le LCD backlight uses LEDs and not an EL foil panel.
Great Video brother God Bless
Del modulo korg ns5r se escurrió la pantalla poquito se ve tendra alguna solución amigo
hi, I am repairing the screen of the KORG I3 and I have removed the battery, so I have lost all memory. can you help me recover the softwear? thank you. i have not floppy.
th-cam.com/video/e-AYL3CEhNA/w-d-xo.html
backlight nya beli dimana?
I have a roland g600 keyboard, and my screen is not bright enough, but do you have that illuminating part for the roland g600? how can I get it?
i found it on ebay.com : EL backlight. but for G600 I believe it is using small LED light from side , maybe some of them died. and check for polarzed film , it is fading along years
Hello .... I have a korg i3 and I want to register a new style ... but I found it difficult .. Can you please guide me to download a video with a detailed explanation of how it works Please😖💕💕💕💕
Cuántos años dura la luz?
Bisa servis korg i3 ngak bos
плохо прижали ..поэтому видна вертикальная полоса..
my display screen comes line, its continue like ur display after placed backlight.so I m not findout the problem pls help to how can restored my display again new
Lines appear if the zebra rubber connectors (black one) not aligned correctly, or blocked with dust/dirt.
@@addiengr1 thank u bro
hi mas. nice video.
bisa replace LCD untuk Korg 01/W FD?
bisa, cuma harus pesan backlitnya dulu, ukurannya sedikit beda
mas Addie.. mohon info..
KORG Trinity saya polarizer nya sudah worn off... apa bisa di tempel lembar polarizer dari luar saja? sekarang layarnya cuma kelihatan backlight, tapi kalo pake kacamata polarized masih bisa kelihatan tulisan nya..
terima kasih banyak buat info nya..
polarizer ada 3 macam setahu saya 0 , 45, 90 derajat untuk posisi paling jelas harus di test polarizernya diputar2, masalah di depan atau belakang bisa saja tapi lapisan lemnya ada di mana waktu beli. bawah atau atas.
@@addiengr1 betul sekali mas, kalo pake kacamata di rotate 90 drajat baru jelas tulisan nya.. masalah nya saya mau bongkar dan lepas polarizer nya dari dalam ga berani.. (keyboard nya masih kayak baru krn cuma disimpan di hardcase, cuma masalah di polarizer ini saja)
apa ada info dimana saya bisa dapet polarizer untuk di tempel di luar touch screen nya saja hanya supaya bisa liat info layar nya?
sekali lagi terima kasih banyak buat respon dan info nya... appreciate it..
@@papankunci bisa beli polirezer film punya screen laptop atau monitor PC, saya potong sesuai kebutuhan. kalo polarizer aslinya korg mungkin sudah gak ada atau harus pesan ke luar.
@@addiengr1 terima kasih buat info nya mas Addie... baik coba saya cari2 yg bisa buat experiment di tempel dari luar dulu... ga keliatan bagus ga apa2 asal bisa baca tulisan nya saja...
sukses selalu ya mas...sekali lagi terima kasih banyak..
Bagaimana saya boleh hubungi anda? Saya dari johor bahru. Nak tanya sikit pasal keyboard i3. Screen saya pun rosak
Bisa kontak ke email adi.ngr1@gmail.com
bang bisa benerin LCD korg karma?
Mas kalau batre CMOS nya gak di ganti gpp kan mas? Saya gak punya disk nya buat load ulang kalau data2 keyboard saya hilang
bisa pakai trik jumper kabel, jadi pas ganti baterai gak putus aliran baterainya
@@addiengr1 maaf nanya lagi mas, itu yg hilang semua program bawaan KORG I3 nya atau hanya program buatan user mas kalau cabut batre CMOS?
om kalo korg N364 saya ga ada backlight nya kira2 harus diganti part yg mana ya??thnx b4
iya sebagian ada yg pakai layar LCD dot matrix. tidak pakai backlight. cek awal koneksi solderan tua yg korosi atau sambungan semua kabel. kerusakannya bgmn
@@addiengr1 belum saya bongkar sih,,tar sekalian bersihin tombol2nya deh biar enak lagi mencet2 nya hehe,,thnx ya om
Mas nerima jasa service kah? Saya punya i3 mau di rapihin. Lokasi ciputat, Tangsel.
rusak apanya mas
@@addiengr1 lampu layar mati mas, terus bendingnya gak berfungsi. Mungkin karna kotor juga dalemnya, soalnya udah lama di gudang mas
Bang beli di online shop indonesia ada ngk?
saya beli di ebay, belum cek lokal
Mas bisa repair lcd korg x50? Bisa di share kontaknya? Trims
kenapa layarnya
@@addiengr1 sy udah kirim video nya ke gmail mas, silakan dicek
very helpful as my lithium battery was dead I had the confidence to change it after watching this video thanks and it's working.