I like how you fold under the lip of the bottom of the pocket. This makes for a stiffer tube and creates a smooth edge that a plant branch won't saw itself off with when the wind moves it.
I made my rendition of the quad station and now moving into final copy; additionally I will be 3d printing my net cups for lengths as well as my seat for the cups. Resourcing materials ideas; if you go onto a construction project; 3’ to 4’ often is wasted and they end up in the garbage piles… I find that Canadian pvc pipe is much thicker and will split even with adequate heating for reaming. I will be developing a method that only requires a stencil and hole cut due to thickness of pipe due to frost line requirements
@@Sukasuka i mean when i follow your style my pipe tear so bad im quite confused should i only heat the part where the pvc cut ends? to avoid tearing it and making a bigger hole ?
@@Sukasuka Is there a lighting system that works well with vertical planting indoors? Most of the lighting systems I see look better for horizontal systems. Are there hanging lights?
So, once your plants get more mature, how many times a day are you adding more water? I have a rail system with around 70 plants (lettuce/kale/Swiss chard) and on warm days, it can go through 4 gallons of water. I use a 17 gallon tote for my res. I don’t see how this thing can keep enough water in it without constant refilling. Plus, it’s all exposed so the water temps would rise when in direct sunlight.
You need to figure out where to put a reservoir, where the pipes will drain to and how you will distribute the water, I have to add about 2 -4 gallons a day to mine (tomatoes and cucumber). A system this size will be very thirsty. Like the idea
Is the density of the pots too great? Will the plants be competing for space and sunlight? How about harvesting difficulties because of the density of the plants?
instead of 90s on the center 2 up rights, you should just have used tee's. This would give you more water capacity and not made any difference to the look.
HOW LONG DOES IT TAKE TO MAKE 10 HOLES ON ONE PVC PIPE? DOES IT ANY ONE OF AN EASIER WAY TO DO THIS? ARE THERE PRE-FORMED PVC PIPES AVAILA LE? IF SO, WHAT ARE THE SUPPLY SOURCE & COST?
Cost is 1.5 Mtr. Pipe with Pocket Holes along with net Caps Rs.1000 +GST+Shipping Other material you can Purchase Locally. If you need Complete Kit also can be Provided based on your Requirement / Design. MOQ 4 UNITS
The thumbnail lies, there are hardly 20 holes in every tower (which is plenty) and if math is not an opinion there should be a total of about 160 holes, where did he get that 270 or something 🤣🤣🤣
![เปิดบ้าน นาราเครปกระเทย 1 ไร่ ขายขาดทุนหลัก10ล้าน เอามาใช้หนี้!!! l [Nickynachat]](http://i.ytimg.com/vi/0jz84VFWVP4/mqdefault.jpg)
![ปฏิเสธไม่ไหว (Crush on you) - LIPTA feat. No One Else [Official MV]](http://i.ytimg.com/vi/NBw1jF342vw/mqdefault.jpg)
Ini untuk hobi sambil mencari pasar, setelah peminat tanamannya banyak, baru beralih ke produksi.
This is next Gen farming.
If my next apartment has a balcony, I will 100% be building this. I've got this series saved. Thank you :)
Great video, but sorry I think I miss how do I connect the water supply?
I like how you fold under the lip of the bottom of the pocket. This makes for a stiffer tube and creates a smooth edge that a plant branch won't saw itself off with when the wind moves it.
You could easley file the edges with a rasp but ya it seem just as easy to roll the edge.👍
Bang,, btw... Kira2 sediain pipa 4 " brp batang itu bang sebelum dipotong-potong?
Thanks for providing all the details. I will be trying to make a rendition of this soon. First I need to save up for all the parts. Thanks!
How many 4 inch pipe was used?
I made my rendition of the quad station and now moving into final copy; additionally I will be 3d printing my net cups for lengths as well as my seat for the cups.
Resourcing materials ideas; if you go onto a construction project; 3’ to 4’ often is wasted and they end up in the garbage piles…
I find that Canadian pvc pipe is much thicker and will split even with adequate heating for reaming. I will be developing a method that only requires a stencil and hole cut due to thickness of pipe due to frost line requirements
Can you tell me why you using a coupling cant you just take the 4" pipe straight through to the elbow?
You can, but having the coupling allows you to remove a tower and clean inside easier
How would the water system work can you do a video
Are you worried about PVC leaching chemicals? Are the materials food safe?
great video. I am excited to see part 2. Looking to do something like this.
Total biaya pembuatan kira2 berapa bang
hello, do i really need the white pvc? because i used orange before and it tear so bad the holes are not clean
you need a strong pipe, the color does not affect
@@Sukasuka i mean when i follow your style my pipe tear so bad im quite confused should i only heat the part where the pvc cut ends? to avoid tearing it and making a bigger hole ?
Cleanest build for a vertical tower. Kudos! 👊
No water source? How you going to water all 8 towers?
Best DIY I have seen
Agree. Even though he didn't talk to explain, the way he did explains everything already. Impressive demo.
Lol but how do you get water into them
Please send me the list of materials
Hi, what is the thickness of the tube 4 inch? 1.8 / 3.2 ! ..
Hello brother, what inch of net cups did you use ?
Hi, i use 5Cm
What would be the best way to light this if it was indoors?
Hi, sir, what do you mean, sorry i don't understand
@@Sukasuka Is there a lighting system that works well with vertical planting indoors? Most of the lighting systems I see look better for horizontal systems. Are there hanging lights?
So, once your plants get more mature, how many times a day are you adding more water? I have a rail system with around 70 plants (lettuce/kale/Swiss chard) and on warm days, it can go through 4 gallons of water. I use a 17 gallon tote for my res. I don’t see how this thing can keep enough water in it without constant refilling. Plus, it’s all exposed so the water temps would rise when in direct sunlight.
Yeah the towers are good but the rest is expensive garbage and won’t work properly
Please do more videos on hydroponics
Well done. Thanks for sharing. SD California.
thank yo
What’s the measurement for the slit that you cut is it 2inches 50mm ??
Yes sir
Sistem pengairannya gimana tuh?
Jadi total butuh brp batang pipa pvc 4"?
mantap designnya..lanjutkan berkarya.
You need to figure out where to put a reservoir, where the pipes will drain to and how you will distribute the water, I have to add about 2 -4 gallons a day to mine (tomatoes and cucumber). A system this size will be very thirsty. Like the idea
What’s a good pump for this system?
what do you mean?
Is the density of the pots too great? Will the plants be competing for space and sunlight? How about harvesting difficulties because of the density of the plants?
Hi, can you please suggest what pipe to use?
I don’t know where you are but I don’t think you can get pipe like that in the U.S. It’s very thin-walled.
How do you stop the heated pipe from splitting when making the hole?
it will not split, just a bit careful
I found the trick is not to over heat it. The ones I overheated ripped the edges. Just heat until it’s just pliable.
Mesin air hidup jam berapa aja mas?
Seperti biasanya, kita hidupkan 24jam
This looks nicely done
do you sell these
sure, we sell, you can contact me +62811239805
What is the total cost?
less then 200$
how will you water those ?
check my part 2
udah dicoba dengan menyemai tanaman di vertical pipa ini pak?
Sudah, hasilnya sangat bagus, sayangnya pipanya sudah di pakai temen, jadi belum bisa tunjukin hasilnya
Thanks for Fantastic video
Plz querier this products from me
Untuk ukuran netpot brpa cm tu Om.. pakai pipa brpa inch?
ukuran standard aja om, pipa yg mana om? semua pipa ada di deskripsi om
@@Sukasuka ditunggu video slnjutny Om 👍
Semakin top dehh
How much size is the tapered pipe that used to hole shape the pvc pipe
1.5"
or 2 inch as per requirement of Crop i.e. 1.5 is for Leafy Vegetables and 2" is for Vegetables for easy withstanding of the plant.
Thankyou and also what is the capacity of the pump
Estimasi biaya abis brp ini bang?
kurang lebih 2jt kak
I always watch your video
Order online bisa?
ga jual saya ka, hehe
Thank you. Great video
Excellent very inspiring
thank you, share please
I love your vlog
dengan 8 tower yang elegan hydrophonik nya
brilliant!
i think you dont know where did you made a mistake isn't it?
Apikk ceh 😍
where the risult?
result will be upload soon :)
Me gustaría verlo funcionando
instead of 90s on the center 2 up rights, you should just have used tee's. This would give you more water capacity and not made any difference to the look.
Pake hairdrayer bisa gg y
bsa kak, asal panas aja kak
Wooow, thanks for this
Semangat bikin video ka :)
*****Be sure to glue the piping together or you will certainly regret***
Gampang ternyata 🤪
Thank you Sir 😊
Nice
Interesting...
216 not 261
Kreatif
HOW LONG DOES IT TAKE TO MAKE 10 HOLES ON ONE PVC PIPE? DOES IT ANY ONE OF AN EASIER WAY TO DO THIS? ARE THERE PRE-FORMED PVC PIPES AVAILA LE? IF SO, WHAT ARE THE SUPPLY SOURCE & COST?
Cost will be different in your country, please check description for detail
Cost is 1.5 Mtr. Pipe with Pocket Holes along with net Caps Rs.1000 +GST+Shipping Other material you can Purchase Locally. If you need Complete Kit also can be Provided based on your Requirement / Design. MOQ 4 UNITS
@@vasudhagreenfarmsmannesn8709 great
In the United States a system like this would be well over $1,000 USD.
mantap..
makasih kak
part 2 bang lanjut
echigla matanca gatun gatun jakuba
The thumbnail lies, there are hardly 20 holes in every tower (which is plenty) and if math is not an opinion there should be a total of about 160 holes, where did he get that 270 or something 🤣🤣🤣
Yes, sorry, is will be 160, I’m wrong calculating 🙏
Excellent thank you 😊
Where is part 2 ?
PVC is stable and does not leach petrochemicals into the water unless you heat it - so you heat it. Wtf?
Yup, you can get straps for 1-1/2 fittings and just cut holes with a drill
Materials needed, $500 of PVC pipe and one can of $10 glue.. 😆
Wearing a mask in the empty space in front of a mechanical object... ?? smart? :-) ha-ha! thank you for the joke.
xoxoxo
Thanks for sharing. Sad though to see you wearing a mask to work alone and outdoors...
Corona timee :D
@@Sukasuka Yep, the virus that turns people into sheeple 🐑🐏
@@Sukasuka Bro for 8 PVC what submercible pump you use ?
Great video by the way 😎💪
Music is annoying
klo seperti ini lebih mahal ya jatohnya
jauh lebih murah kak jadinya ka
Hello, the tube you use to shape the hole after heating, what measurements is one or two inches?