Good-luck with that,🙄, Alex only makes video's when someone sends him something for free,🤑, these companies sending him stuff should demand more than just one video from him.😋👍
$350+, 6mm mounting instead of 8mm, Only one proprietary exhaust option & finally no piston port variant. Very hard to make that purchase when you can pay $80 for a 49mm iron bore.🤔 Did you pay for it or did the bike berry dude hook you up?
Bt100 has lots zink in casting materials made in chin lousie indina foundries. Lots zink cadmium makes it crack easy. All the metal is pot metal in bt engines. Same factories that make hone drpo (amazon brand) weedeater things blow up after 7 uses worse then China made castings lolz steel probably flung cast steel then bored out with razorblade 😂 you know for sure this was a freebie arsh kiss video😅 so huge cause all zink retains heat Lack of sleeve index point is dead give away spun casted steel sleeve. Zink makes it nice dull shinny white color though😂 oil resistant easy to clean😮 best thing this whole damn engine is fact it has 14mm pistion wrist pin lol
My bt100 has 3 piston rings the bt100.2 on the video only has two will this change the compression? Also those reed valves look amazing, engine size might be a little too hunky for a pleasant ride and a two piece jug might have compression loss if gaskets are not seated properly. All in all looks amazing hope it performs wonderfully yet I do have some concerning questions especially heat transfer to carburetor and piston performance with one less piston ring
I think this is what we have been wanting from a 100 they already had great power but they always got to hot and melted the exhaust side of the cylinder walls and piston this iron sleave and more surface area of fins and the humongous head this should last at 3/4 / wide open for as long as you want and be able to do the long distance drives a modified 80 can do like 200 300 kilometers round trip
@@z28kid71 👈🏼🤔 WRONG! That's Not "a humongous head". The cylinder & head is one unit together as one pos poor design. "Drives"?! One RIDES a bike & "drives" a four wheeled vehicle. JS
I actually like the 2 bolt chain tensioner because of the straight vertical adjusting slot. I just drill out 4 corner holes and make it a 6 bolt. I wrap skateboard grip tape on the frame chain stay where I clamp the tensioner and it dosen't move at all.
@@dustinh4175 Anybody that knows their sh¡+ knows that chain tensioners are dangerous and unnecessary on most applications. If you can't adjust and or shorten your chain properly and if you have to use one, use it on the pedal side if you think you need one. I get my chains the right length or make them the right length where my drop~outs has all the adjustments necessary. More quiet, less, bs, & just better period.
I would like to see the bore and stroke checked to make sure the stroke is 40 mm not 37 mm also would like to see how they stuffed the case. And also would like to see what the transfer ports look like with the person at the bottom center to the transfer ports clear of the piston are does the piston block part of the port which would restrict flow into the cylinder?
Can I get a good Recommendation on 2 cycle oil I'm buying a bike in the next couple of weeks and I'm trying to find the best oil to use for it. Thank you
btw why they don't wan't make the magneto little bit bigger and heavy and aslofo flywheel wheight get heavy to, cause they importarn for get inertia movement from that magnetto to help crankshaft rotate easily???
I have a question, i have a bt100 v1 and as far as i know, the only mods/upgrade i can do to my engine is to change the block/cylinder head to make it v2. I didn't see any video on YT modifying this engine or even any of the shelf parts that's plug and play... So theres the question, what other mods can i do to the engine? Thanks...
Let's play along and say this will make 5hp. That's enough to go 60km/h (37mph). Downhill 70-80km/h. If you're going that fast on bicycle tyres & brakes (even hydraulic discs) you are a hazard to yourself and others. These things look cool to kids & convicted drunk drivers but more than a few people get killed on them.
excited? For another super cheap jank ass 2 stroke? nah, man. it's 4 strokes or nothin. I use these motorized bikes to make money. When they aren't broken on my porch. Which is 85% of the time. I'm done with 2 strokes.
For a newbie (myself) what engine would you recommend? Note. I'm considering for use as a paramotor? Also your recommendations on most reliable 2 stroke you have been exposed to? Expansion chambers and modifications? My thinning is that if this is your bread and butter you are going to have some experience about various different engine types and modifications? I do acknowledge your dislike for 2 strokes also, but as a paramotor application running mostly as a stationary motor most of the time? I'm considering power to weight and hope you can look past your exposure to these motors in a motorised bike application?
@@jameshatton4211 bike motors have reduction gearing to drive a bicycle wheel, not a propeller. Even if you could make it work, you definitely don't want a low quality, low reliability bike motor to go flying with, at any price.
@@vk2aafhamradio I'm new to this, and planning to do my first motorized bicycle build soon. Is there such thing as a bicycle motor that's NOT low quality? If so, 🙏please, do tell, and point me in the right direction?
Oh' i donth' wahnt have the! Big moulf bat i forget too' thold be'fore Open the original engine doo' First Name: Druck Probe. If everything Name: dicht 85- 95 % soo' No Name: dichtflächen Fehler. Jes after meby poriting.
Alex, thanks for calling me back was surprising to hear from you. Watch you all the time Thanks for all your advice and getting back to me fast
very interesting seeing all these motorized bike motors evolve
Can't wait to see how it runs right out the box and after the break in period
Good-luck with that,🙄, Alex only makes video's when someone sends him something for free,🤑, these companies sending him stuff should demand more than just one video from him.😋👍
Good to see another video my man!
Great Video, Lots of information. Yea They did it Right, I AGREE on thee THUMBS UP, definitely going to be a HOT Little RACE!
Já estou ansioso pra ver ele no Dinamômetro!
Gracias por mostrar estos motores los conosco por tus videos gracias soy entusiasta de estos motors y vivo en cuba
$350+, 6mm mounting instead of 8mm, Only one proprietary exhaust option & finally no piston port variant. Very hard to make that purchase when you can pay $80 for a 49mm iron bore.🤔 Did you pay for it or did the bike berry dude hook you up?
Agreed, overpriced junk
😂 I think the BikeBerry guy set him up. Ouch.....I have a 47mm china Doll that could take this motor on😎
th-cam.com/video/0RzH1eDA6lE/w-d-xo.html
Agree.
Anyone else notice the 3 huge cracks in top end 2 in head? It's so huge cause so poorly made only way it doesn't overheat lol
Bt100 has lots zink in casting materials made in chin lousie indina foundries. Lots zink cadmium makes it crack easy. All the metal is pot metal in bt engines. Same factories that make hone drpo (amazon brand) weedeater things blow up after 7 uses worse then China made castings lolz steel probably flung cast steel then bored out with razorblade 😂 you know for sure this was a freebie arsh kiss video😅 so huge cause all zink retains heat
Lack of sleeve index point is dead give away spun casted steel sleeve. Zink makes it nice dull shinny white color though😂 oil resistant easy to clean😮 best thing this whole damn engine is fact it has 14mm pistion wrist pin lol
Happy thanksgiving alex❤
I can forcast fuel boiling issues with that carburator so closed to the power plant
looks pretty quality
Please do the 300 mile update Full Send Video. Love the vids Alex. Overpriced engine. Rather get a Phantom but still nice
Lol 50mile 😂 video 300 is only is Jesus personally drove it😅
@@BuildBreakFix Rode not "drove" there's no steering wheel.
Those transfer ports look like they’re barely angled. Almost like the BT 80 electric start motors and the 110cc motors.
My bt100 has 3 piston rings the bt100.2 on the video only has two will this change the compression?
Also those reed valves look amazing, engine size might be a little too hunky for a pleasant ride and a two piece jug might have compression loss if gaskets are not seated properly. All in all looks amazing hope it performs wonderfully yet I do have some concerning questions especially heat transfer to carburetor and piston performance with one less piston ring
I'm going to buy the phantom 85. I got some questions on what would be the best kit to get I'm looking for 45 to 50 mph and Reliability.
You should see if that top end will fit the fisrt gen bt100
It does!
How do you know it wasnst locktited and torqued down
The only thing that sucked right off the bat was there's no 12 mm piston pin clip
Yea I want one.
I think this is what we have been wanting from a 100 they already had great power but they always got to hot and melted the exhaust side of the cylinder walls and piston this iron sleave and more surface area of fins and the humongous head this should last at 3/4 / wide open for as long as you want and be able to do the long distance drives a modified 80 can do like 200 300 kilometers round trip
@@z28kid71 👈🏼🤔 WRONG! That's Not "a humongous head".
The cylinder & head is one unit together as one pos poor design.
"Drives"?! One RIDES a bike & "drives" a four wheeled vehicle. JS
I actually like the 2 bolt chain tensioner because of the straight vertical adjusting slot. I just drill out 4 corner holes and make it a 6 bolt. I wrap skateboard grip tape on the frame chain stay where I clamp the tensioner and it dosen't move at all.
@@dustinh4175 Anybody that knows their sh¡+ knows that chain tensioners are dangerous and unnecessary on most applications. If you can't adjust and or shorten your chain properly and if you have to use one, use it on the pedal side if you think you need one. I get my chains the right length or make them the right length where my drop~outs has all the adjustments necessary. More quiet, less, bs, & just better period.
Bro what happened to Zeda motorsports??? Was it a scam after all??
Lol Zeda is so 2019
New vids?have you ran it yet?
That's a lot of "nice and clean" for a brand new engine lol
True the iron sleeve will last MUCH longer than an aluminum one
It’s so fn thick. Bored out wouldn’t be something I’m opposed to seeing
I would like to see the bore and stroke checked to make sure the stroke is 40 mm not 37 mm also would like to see how they stuffed the case. And also would like to see what the transfer ports look like with the person at the bottom center to the transfer ports clear of the piston are does the piston block part of the port which would restrict flow into the cylinder?
The engine look nice but i dont like the reed valve side way
hopefully they aren't to big for certain frames
You’ll be damn sure it is, that looks pretty beefy
We're is the ride video
Is it better than the LD100?
Can I get a good Recommendation on 2 cycle oil I'm buying a bike in the next couple of weeks and I'm trying to find the best oil to use for it. Thank you
Opti2
No squish? Way?
btw why they don't wan't make the magneto little bit bigger and heavy and aslofo flywheel wheight get heavy to, cause they importarn for get inertia movement from that magnetto to help crankshaft rotate easily???
So what happened with thia engine?
BUT DOES IT HAVE A WINDOWED PISTON FOR THE REED VALVE YET?!
Let’s race!
Thats! 100 CC Low price 🚴 engine Look's nice. If have know how , parts everything nice meby about 12- 15 HP.
I'm sold/
Big fins for cooling is good but it is also bad. a big engine does NOT fit in most bicycle frames.
No window in the piston seems off
I thought u had to have a windowed piston with a reed valve? Piston not windowed so has does that work?
I have a question, i have a bt100 v1 and as far as i know, the only mods/upgrade i can do to my engine is to change the block/cylinder head to make it v2. I didn't see any video on YT modifying this engine or even any of the shelf parts that's plug and play...
So theres the question, what other mods can i do to the engine? Thanks...
Hey Alex😊❤
I do not see any technology improvement to justify the price. It's only look better.
You my sir are blind in every way possible
@@z28kid71 5 other's so far agree with my post comments. And we are the potential buyer's.
@@z28kid71 Just a different cylinder bro. Go ahead and buy that turd then.
I’m looking for a throttle for my motor bike I see that we both live in the same city
What is the white wire for
these drive gears should be 13 teeth not 10.
Gravity does not play a part on reeds when it "sideways." However gravity would play a part on the bottom reed if it was oriented up and down.
Где купить такой мотор пору штук бы взял
Does the head fin top fit on the Pantom 85?
Hayır olmaz.
So is that iron sleeve replaceable?
it's better than v1 but too much $$ and now fits in wayy less bikes. what's it weigh, is it a pig?
It's a pig. Runs cool though
,,how much the price
150 €vro .
Another pos for $350. Carb and exhaust are junk. Come on stop trying trying to fool the new guy. So you can put money in your pocket!
Let's play along and say this will make 5hp. That's enough to go 60km/h (37mph). Downhill 70-80km/h. If you're going that fast on bicycle tyres & brakes (even hydraulic discs) you are a hazard to yourself and others. These things look cool to kids & convicted drunk drivers but more than a few people get killed on them.
@@vk2aafhamradioyou can get Michelin E bike tires rated for 90kph ,even track pedal bikes go 50kph+
@vk2aafhamradio Well just take the brakes off then!😂 'Most everybody's got shoes👞! 😜
does this cylinder fit the old bt100?
yeah , bike berry has a video on it
👍💯🐟👋👋👋👋👋
Wow what a horrible job, v1 bt was better, this thing is overpriced junk
I can't believe he doesn't have one thing bad to say about.🙄😒 He's all over Tony from dingleberries nutz.
excited? For another super cheap jank ass 2 stroke? nah, man. it's 4 strokes or nothin. I use these motorized bikes to make money. When they aren't broken on my porch. Which is 85% of the time. I'm done with 2 strokes.
For a newbie (myself) what engine would you recommend?
Note. I'm considering for use as a paramotor? Also your recommendations on most reliable 2 stroke you have been exposed to? Expansion chambers and modifications?
My thinning is that if this is your bread and butter you are going to have some experience about various different engine types and modifications?
I do acknowledge your dislike for 2 strokes also, but as a paramotor application running mostly as a stationary motor most of the time? I'm considering power to weight and hope you can look past your exposure to these motors in a motorised bike application?
@@jameshatton4211 bike motors have reduction gearing to drive a bicycle wheel, not a propeller. Even if you could make it work, you definitely don't want a low quality, low reliability bike motor to go flying with, at any price.
@@vk2aafhamradio I'm new to this, and planning to do my first motorized bicycle build soon. Is there such thing as a bicycle motor that's NOT low quality? If so, 🙏please, do tell, and point me in the right direction?
Oh' i donth' wahnt have the! Big moulf bat i forget too' thold be'fore Open the original engine doo' First Name: Druck Probe. If everything Name: dicht 85- 95 % soo' No Name: dichtflächen Fehler. Jes after meby poriting.