Hi Onos: I just ordered the model OP320-A-S and the cable USB-MD204 using the link you recommend. I hope you make more videos with this HMI and FLProg. I love FLProg! Greetings!😀!
Nice project! The schematic has an error, the ground on the relay board must be connected to the Arduino ground. If it works without this it is only by luck.
Hi. If any one could make clear is one small detail before try to learn about this software. The arduino nano is running a full micro independent or is been drive as slave from the PC be USB cable Thank to any one answer the question.
The Arduino nano is running a full micro independent and not driven as slave by the PC. The USB cable is to provide power supply for demonstration purpose. It only act as slave to the OP320 panel for signal mintoring and control. You can start learning from here: How to Program Outseal Arduino PLC: th-cam.com/play/PLjkzNLFcHTFAVyg3gAH5P-akRdKhYz9-P.html
If possible please make a video for hardware and software configuration setup in which analog values to display thank you... Waiting for a positive response
OUTSEAL do not support Arduino Mega 2560 but Atmega 128 as shown in this videos: Outseal PLC Mega: th-cam.com/play/PLjkzNLFcHTFDDxfC8gr7Vih8LcLQrmiMN.html If you follow the video series particularly on Modbus, you should be able to achieve your design. How to Program Outseal Arduino PLC: th-cam.com/play/PLjkzNLFcHTFAVyg3gAH5P-akRdKhYz9-P.html
@@OnosTech is that something you would show in a video, set up and communication with a couple of them? I do like your tutorial videos, some of the best I’ve seen.
Hello my lord, permission to ask I am using HMI OP320 5.6, the problem is downloading the program "Time-out, Please check cable and power, download again" cable using RS232, please respond.
Hi, please confirm that you installed OP20 V6.5y software or else download and install it with the link in the description. This version should work for OP320 5.6
Your videos for most learning material...
So nice of you
Great video!! I was looking for a low cost LED display with buttons and you have found it for me. Keep the video's coming!!
Thanks😊😊😊
Hi Onos: I just ordered the model OP320-A-S and the cable USB-MD204 using the link you recommend.
I hope you make more videos with this HMI and FLProg. I love FLProg!
Greetings!😀!
🙂🙂🙂 Many thanks for supporting this channel. I already have a scheduled video for next month on this.
If possible in LDMICRO PLC communication in UART PROTOCOL OP320 HMI?
very informative video ... thanks a lot !
I am glad it's helpful
Perfecto... very helpful.. thanks sir..
Many thanks
Nice project! The schematic has an error, the ground on the relay board must be connected to the Arduino ground. If it works without this it is only by luck.
Yes, you are right. Thanks for noticing and pointing it out. Editing omission.
Hi. If any one could make clear is one small detail before try to learn about this software.
The arduino nano is running a full micro independent or is been drive as slave from the PC be USB cable
Thank to any one answer the question.
The Arduino nano is running a full micro independent and not driven as slave by the PC. The USB cable is to provide power supply for demonstration purpose. It only act as slave to the OP320 panel for signal mintoring and control. You can start learning from here: How to Program Outseal Arduino PLC: th-cam.com/play/PLjkzNLFcHTFAVyg3gAH5P-akRdKhYz9-P.html
If possible please make a video for hardware and software configuration setup in which analog values to display thank you...
Waiting for a positive response
Thank so much;;; It´s amazing. congratulations
Thanks
Okay outseal also support Arduino mega 2560 board ? Plz make a video use 2560 Arduino board with HMI OP320-a I hope you make it thank you...
OUTSEAL do not support Arduino Mega 2560 but Atmega 128 as shown in this videos: Outseal PLC Mega: th-cam.com/play/PLjkzNLFcHTFDDxfC8gr7Vih8LcLQrmiMN.html
If you follow the video series particularly on Modbus, you should be able to achieve your design. How to Program Outseal Arduino PLC: th-cam.com/play/PLjkzNLFcHTFAVyg3gAH5P-akRdKhYz9-P.html
Thank you Sir.. waiting for positive response
Many thanks for the suggestions
@@OnosTech thank you for reply
@@OnosTech and wait for video...
As said....above
I know I asked this on the LDmico but is it possible to communicate with the serial connections of a Nextion display to then have a touch screen HMI?
Nextion display can communicate with LDmicro, but not with Outseal since Outseal uses only Modbus protocol.
@@OnosTech does that mean that Outseal doesn’t have any functions for SPI or I2C?
It does. The communication instructions group has them TWIR etc
@@OnosTech is that something you would show in a video, set up and communication with a couple of them? I do like your tutorial videos, some of the best I’ve seen.
OPENPLC SOFTWARE is good rather than outseal because analog input option is more than outseal only two analog inputs have
In video Arduino mega 2560 or Arduino Uno and inter face with HMI OP320 (display analog values and push button and lamps etc
Hello my lord, permission to ask I am using HMI OP320 5.6, the problem is downloading the program "Time-out, Please check cable and power, download again" cable using RS232, please respond.
Hi, please confirm that you installed OP20 V6.5y software or else download and install it with the link in the description. This version should work for OP320 5.6
If you add ESP32 for remote control, is that possible?
th-cam.com/video/7aq8GNwlCxo/w-d-xo.html
@@OnosTechhow is the wiring to connected plc outseal,esp32,and op320😁
can make program please
I am sure you can make the program yourself if you follow the related tutorial series in this channel
@@OnosTech can you sent your email
Great tutorial.
Thanks
can you help me print word to HMI ?
I am not sure I understand you
very nice tutorial but you no showing wiring diagram of all circuit in this project
Sorry for the omission of the DB9 connector from the circuit connection. Please see description for the link to the complete diagram
@@OnosTech ok, thanks for your afford
HI good job! One question? Can you give me the register list for OP320? Thanks
Thanks! Do you want the Modbus register list for Outseal PLC?
@@OnosTech I need modbus register for OP320. You'd be so kind if you can give me! Thanks
@@OnosTech Do you have?
@@stefanomilesi4702 I am not sure I understand what you want, but here is the manual: kms-trade.com/downloads/manuals/OP_HMI_HardwareManual.pdf
@@OnosTech I am looking for the list of registers you have to query with communication Modbus RTU from PLC to OP320.
Ótima Aplicação
Thanks a lot
Plz Make a video (OPENPLC SOFTWARE)
TQ Sir ❣❣👌👌
You are welcome
Nice video
Thanks 😊😊😊
Serial communication
Module name ?
OP320 Operator Panel s.click.aliexpress.com/e/_AqfKEZ
And also hardware wiring...
How r u ?
I have Arduino mega 2560
And DELTA HMI
Communication with RS232
Hello I am IMTIAZ AHMED from Karachi Pakistan plz make a video op320 hmi configuration in LDMICRO
I am not sure
@@OnosTech hi good day
@@OnosTech I am not understanding what about that?
Hello Sir