Your exhaust manifold (where your exhaust should be) is right above your tyre so dirt can flic up from your tyre into the exhaust manifold and mess up your piston
Definitely put an exhaust on it because if you run it like that you will message up the head. It warps it and you will be out some parts. Don't run it for too long without an exhaust.
Manuel Gutierrez yeah. It was more of an experimental thing. I put a muffler on it right after this video. Just curious how it sounded, and the muffler didn’t come in the mail yet.
That gas looked clear...I hope you're mixing it with 2 cycle oil. And running an engine without an exhaust like that will burn up piston rings fast. I have 2 of these engines they're actually decent for Chinese engines.
I have a Chinese petrol scooter as well but don't know how to start it up and get it in drive. Any ideas? To start it you pull the pull-cord while opening the throttle. However how do you put it in drive after you start it. And are there any other start up stages I'm missing. I know how to use the choke, primer bulb and air-mixture screw. Is there supposed to be an ignition switch or fuel switch as well? I can't see anything.
@@alantaylor6691 oh your dumb guy if you cant put it in drive you cant adjust the carb mix screws there is no drive guy you just pull the gas and go it has a centrifugal clutch that makes the wheel spin only when your on the gas
@@alantaylor6691 To drive it's just like a car that is in drive, just push the throttle and you should go. If it revs with no movement your clutch is bad
I had the xtreme x or something 49cc 2 speed looked similar i had bought the same air filter but bought this weird aircraft aluminum 100 dollar exhaust looked like a small metal brick with groves inside for back pressure that made it so loud almost as loud as no exhaust literally not much different besides the fact its working properly that carburetors a pain when dealing with altitude change also try a high octane 115 you'll notice some crazy power lol i got mine up to 40mph before the belt transmission broke
Hi, I have just acquired a second-hand petrol stand-up scooter just like yours, however I'm not sure how to start it and put it into drive. It also has a kill switch. So to start it you pull the pull-cord while twisting the throttle. However what do you do when you want to engage the clutch to make it drive? It seems that at the beginning you are twisting the throttle and it's not going anywhere, however when you step on it you again twist the throttle but now it's going forwards.
Manuel Gutierrez This one may have been marketed different in the U.S, but it is identical to my engine which came off a skateboard, it's a "Morrison" with a gear-reduction of 6:1, not the most reliable design IMHO coz under high revs for long periods, bolts nuts and mounts tend to rattle loose.
motorve That big screw on top of the trans is the oil-filler, ya meant to unscrew it and top the gears up with oil because there is a small pinion that drives a bigger cog which gives the 6:1 gear reduction.
hi Jaden Rhines I have a solution to your problem with your scooter you haven't put gas in the gas tank for a while so there's a lot of air in the fuel line just keep priming the primer and let all of the air out!!!
@@ericpotencianom9676 your just going to melt your piston because its going to cause the engine to run lean as its sucking air in through the exhaust port
Im not here to be hateful. Just giving advice to you. Not so much priming, less throttle when you are starting it. A few other things too. When you're running a motor. You need some sort of muffler. Because without one, there's no back pressure which means your own head is sucking cod air into a hot cylinder which could cause you to throw a piston, or warp your valves. And that's total Carnage. Just helping out. I speak from experience
put the exhaust on it kid it has no back pressure expansion chamber so its not making shit for power or torque i know it sounds loud but just buy a rc engine expansion pipe
Dude I think you need to take it to a professional and leave it alone so you can get your carburetor tuned up little hard time starting that thing please people do not follow his videos on fixing things.
Hey everyone!! I got a new video of the scooter on my channel!! Go check it out! 😀👍🏻
Cool scooter i got a cooler with a engine in it 33cc I think it runs i got to order a pull cord though.
Maybe the nine thousand times you hit the primer might be an issue why it's not starting
username checks out
I heard he is still pushing it as we speak
😂
Your exhaust manifold (where your exhaust should be) is right above your tyre so dirt can flic up from your tyre into the exhaust manifold and mess up your piston
U need the exhaust on it 4 back pressure just a little bit for it to run right
Sounds like a PIG going Oink Oink when you’re Pull Starting the motor! 😂🐷🐖
hey lad, go easy on the primer bulb I could literally smell that it was flooded, spark plug came out wet like a shower curtain
a workout just to start! I have one as well. I love it
That’s because it’s missing the exhaust. No expansion chamber to aid it.
Gonna melt the rings doing that, it sounds cool but just get a loud pipe expansion chamber with back pressure you need it.
Definitely put an exhaust on it because if you run it like that you will message up the head. It warps it and you will be out some parts. Don't run it for too long without an exhaust.
Manuel Gutierrez yeah. It was more of an experimental thing. I put a muffler on it right after this video. Just curious how it sounded, and the muffler didn’t come in the mail yet.
That gas looked clear...I hope you're mixing it with 2 cycle oil. And running an engine without an exhaust like that will burn up piston rings fast. I have 2 of these engines they're actually decent for Chinese engines.
I have a Chinese petrol scooter as well but don't know how to start it up and get it in drive. Any ideas? To start it you pull the pull-cord while opening the throttle. However how do you put it in drive after you start it. And are there any other start up stages I'm missing. I know how to use the choke, primer bulb and air-mixture screw. Is there supposed to be an ignition switch or fuel switch as well? I can't see anything.
@@alantaylor6691 oh your dumb guy if you cant put it in drive you cant adjust the carb mix screws there is no drive guy you just pull the gas and go it has a centrifugal clutch that makes the wheel spin only when your on the gas
@@alantaylor6691 To drive it's just like a car that is in drive, just push the throttle and you should go. If it revs with no movement your clutch is bad
3 quarters of the video just trying to start it . kill me now
Very cool, I like and remind me of my childhood👍
I had the xtreme x or something 49cc 2 speed looked similar i had bought the same air filter but bought this weird aircraft aluminum 100 dollar exhaust looked like a small metal brick with groves inside for back pressure that made it so loud almost as loud as no exhaust literally not much different besides the fact its working properly that carburetors a pain when dealing with altitude change also try a high octane 115 you'll notice some crazy power lol i got mine up to 40mph before the belt transmission broke
Do you know who make this scooter I just picked one up and I'm missing the back caliper and bracket thanks for the video
I’m trying to learn more about my scooter 😅
Hi, I have just acquired a second-hand petrol stand-up scooter just like yours, however I'm not sure how to start it and put it into drive. It also has a kill switch.
So to start it you pull the pull-cord while twisting the throttle. However what do you do when you want to engage the clutch to make it drive? It seems that at the beginning you are twisting the throttle and it's not going anywhere, however when you step on it you again twist the throttle but now it's going forwards.
its cause hes not revving it high enough on purpose hes not giving it enough gas to drive has nothing to do with stepping on it
Ok so far this is the only one of these I have found on line I have a buddy thats got one thanks for the info about its size
In need of parts BAD BAD
You flooded the engine thats why it was slowly trying to start.
If your motor starts some times it's usually a gas issue. It gets fluded and it won't start all the time and you will always have gas on your plug.
Manuel Gutierrez This one may have been marketed different in the U.S, but it is identical to my engine which came off a skateboard, it's a "Morrison" with a gear-reduction of 6:1, not the most reliable design IMHO coz under high revs for long periods, bolts nuts and mounts tend to rattle loose.
5:00 when the engine finally starts
oliver velez thanks dude.
Thank you
Thx
Why do none of these videos say when starting where the lever should be. In closed or open ? That is all I want to know and it gets skipped.
its a chinese mistake in the manufacturing process on al;l these scooters exept goped mine has same problem up=choke down=open
You need the fan shroud back on to push air over the cylinder head.
that is why i love my electric scooter, one button and you go!
😆 🤣 😂 lol
I need to get wireing diagram for a diablo 49cc chopper if there's any site or if someone can help
there is probably a wire from the coil to the switch and a wire from the switch to ground.
What is that big screw on top of the trans right next to the engine sprocket?
motorve That big screw on top of the trans is the oil-filler, ya meant to unscrew it and top the gears up with oil because there is a small pinion that drives a bigger cog which gives the 6:1 gear reduction.
Chris. G thanks for that info. What kind of oil should be used?
Do you know if they make a big bore kit for this motor
Cool bro. Have you got a vid detailing build or anything like that
michael ashbrook if you need parts I have 5 of thoes motors
Have you tried putting the exhaust on and properly turning the carb? :3
Put an exaust so you can get some back pressure to start it
channel deleted I did, this was just for fun!!
Were did u get those tires
Put a exhaust on 2 stokes don’t like having no back pressure
You need the exaust to start it numbnut it helps the compression
Ponele el escape! Lo necesita para hacer compresión es una pieza esencial para el motor. Así lo vas a terminar fundiendo todo
hi Jaden Rhines I have a solution to your problem with your scooter you haven't put gas in the gas tank for a while so there's a lot of air in the fuel line just keep priming the primer and let all of the air out!!!
That engines not gunna last long with no exhaust
Hello, I would like to know why would you say that an engine won't last long without a muffler? What is reason behind it.?
@@ericpotencianom9676 your just going to melt your piston because its going to cause the engine to run lean as its sucking air in through the exhaust port
@@ericpotencianom9676 and also thats why he is struggling to start it because theres no back pressure and its running lean
You think really get 20 mpg?
Did you buy the scooter
Flooded see all the fuel coming out of the exhaust port.
Im not here to be hateful. Just giving advice to you. Not so much priming, less throttle when you are starting it. A few other things too. When you're running a motor. You need some sort of muffler. Because without one, there's no back pressure which means your own head is sucking cod air into a hot cylinder which could cause you to throw a piston, or warp your valves. And that's total Carnage. Just helping out. I speak from experience
no valves in a two stroke
where you buy it
Your gas line is facing downwards underneath your carb
Mine doesnt start any idea why
Roger Perez gotta have fuel and spark ⛽️⚡️
I have that exact engine on my pocket chopper
I'm still looking for parts for mine. Paid £45 for it. Runs sweet though with this engine in. Finding it hard to find a fuel tank cover for it.
@@sp-mods-cotwnew1159 i have a cover if you need one,let me know wasterdnb@gmail.com
Excelente 🇩🇴🇩🇴🌎
that motors shot bro and plus u flooded the engine
bossedupmaxk Spear yaa dude, the rod sent out of the block after I dumped 2 gallons of gas in the cylinder dude
your arm must hurt
Why don't you ever show how fast it goes?
Te falta poner el tubo de escape pierde la mezcla por hay sin el escape un 2 tiempos muy importante el tubo de escape
nice socks
Onya dude
No back pressure from muffle thats why it's hard starting.
I got one
Oh my god this was only 8 months ago but your voice sounds like it was years ago!
It's like mine, won't start and mine is brand new
😎💪💪👌👌👍👍👍👍👍
I calzini sono abinati al filtro aria😂😂😂😂😂
Bro u put so much fuel in that engine lmao
I have a bladez mobyX it's fast
Hold the brake and give it gas at same time u pull the cord
That’s a terrible idea because then your jamming the piston in moving
@@vladimirvladimirovichputin1352 crawl, walk, run. Do anything u can to get it started...worry about the mechanics afterwards.
Ko biết sửa thì giật nguyên ngày không nổ! 😂
With a hensim motor
bro when raining can damages?
Wtf did i just read?
@@jonlangfeldt4345 😂😂
Why without the fucking muffler you are going to destroy the engine by taking off the muffler
put the exhaust on it kid it has no back pressure expansion chamber so its not making shit for power or torque i know it sounds loud but just buy a rc engine expansion pipe
Vai acabar o vídeo e não pega essa joça
You can run it with out muffler just don’t push it too hard unlesss u want to push it hard fuck it haha
Bati ba ana nga scooter di mo andar kagang kagang elabay na
pal plus nou good
What the fuck is the point taking apart the engine to look like it came from a fucking scrap yard?
Use the fucking throttle when you try to start
ok Mr. "cool guy"
@@jadenrhines234 dude your using non mixed gas no muffler gonna fuck it up
When you try to be technical and flood the motor like a true idiot lol
Вася у тебя хреновый карбюратор походу, и сними арм стартер и крути шуруповертом, а карб либо не настроеный либо прото плохой.
Что это за двигатель?
NOT ENOUGH BACK PRESSURE, if you do it it to start you run a big chance of cracking head or piston
Con un cerillo prende😂😂😂😂😂
Ut jus spoiling the piston
Mesin 737 sr turbo
There’s no back pressure that’s what the muffler is for
It didnt have a spark plug hahha bro
wheels a bit too small for safe driving at high speed
Dude I think you need to take it to a professional and leave it alone so you can get your carburetor tuned up little hard time starting that thing please people do not follow his videos on fixing things.
Failure. Fix and make new video.
Cái xe này nên đốt đi là vừa
You will burn up a valve without a exhaust
There are no valves in this engine
That was funny it's not a 4 stroke XD
lol
jajajaja 4 minute tratando de hacerlo arrancar jajajajaj
The whole point of these new scooters is their electric why we going backwards and making stinking 2stroke combustion they look sound an smell terible
Fail....epic fail. Nice try tho but leave the wrenching to the pros kid.
Bati ba ana nga scooter di mo andar kagang kagang elabay na