We have used the th-cam.com/users/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!
Nice video. I have the same engine on an old Craftsman mower. Just recently started stalling. Engine runs find for about 2 minutes then seems to get hot, rpm's slow, then the motor won't start for about 30 minutes. Oil, fuel all good. With the cost of new mowers today a rebuild is in order.
I didn't see you positioning the gap in the new rings - gap in oil ring straight up and gap in compression rings one 90degrees left and other 90degrees right.
what rebuild? Nothing scored, sanded, honed, flattened, new seals, how are the valves? Just putting it together on the bench. What was it taken apart for?
Those washers bend upward to stop the bolt from turning and coming undone. They're joined in the middle so the washers themselves don't twist trying to prevent the bolt from coming undone.
I have few mechanical skills. Is there a manual that would detail this process? I have that engine on an old Yard machine 3 in 1 lawn vac. I took the muffler, pull starter , air filter assembly and gas tank section off to remove a mouse nest that was causing it to overheat. I was careful to lay the pieces out in relation to where they attached to the block. I lost the" flywheel stabilizer" and spent a day with a metal detector finding it. My error was waiting almost 2 weeks to attempt reassembly. I am confused as to which bolts are used where and the order to assemble components. Now I realize that I may get torched leaving this question here, but believe it is worth it. This site has me fired up to get my Dad's old 1960 Allis Chalmers riding tractor rolling again. Thanks in advance for your help!
Good Job ! What was wrong with the engine?? Somebody run it without oil??? Most typical....did you change piston/pistonrings?? And finally, what is valve-clearanse: I and O?? Thank you, youtheman =)
![[Watch Party] RoV Pro League 2024 Winter | with Moowan ( Bacon Time Vs Talon )](http://i.ytimg.com/vi/CCEDhu6dPN8/mqdefault.jpg)
We have used the th-cam.com/users/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!
Great job. I really gained a lot. Thank you so much. More grease to your elbow and more wisdom always.
Awesome! Thanks for sharing.
I was going to say I noticed that cylinder wasn't honed for those new rings but if it's only for an example yea all good.
Nice video. I have the same engine on an old Craftsman mower. Just recently started stalling. Engine runs find for about 2 minutes then seems to get hot, rpm's slow, then the motor won't start for about 30 minutes. Oil, fuel all good. With the cost of new mowers today a rebuild is in order.
Best Series 👍🏻
Thank you daggwin, really helped me out :)
Last song ,Music is open sea morning - puddle of infinity
I didn't see you positioning the gap in the new rings - gap in oil ring straight up and gap in compression rings one 90degrees left and other 90degrees right.
what is the music you used about four minutes through the video ?
Excellent video.
what rebuild? Nothing scored, sanded, honed, flattened, new seals, how are the valves? Just putting it together on the bench. What was it taken apart for?
stuff a sock in it Ahole.
Hello, could you tell me how to get piston rings and a head gasket for this engine please
Great video, very helpful 👍 Do I need to put instant gasket on crankcase before I drop the new gasket on, or just straight on with the gasket?
What was screwdriver used for on the muffler bolts? I couldn't tell what u were doing there.
Those washers bend upward to stop the bolt from turning and coming undone. They're joined in the middle so the washers themselves don't twist trying to prevent the bolt from coming undone.
@@gavmansworkshop5624 you are right. I wanted to help him this but you have done an excellent job. Thank you.
I have few mechanical skills. Is there a manual that would detail this process? I have that engine on an old Yard machine 3 in 1 lawn vac. I took the muffler, pull starter , air filter assembly and gas tank section off to remove a mouse nest that was causing it to overheat. I was careful to lay the pieces out in relation to where they attached to the block. I lost the" flywheel stabilizer" and spent a day with a metal detector finding it. My error was waiting almost 2 weeks to attempt reassembly. I am confused as to which bolts are used where and the order to assemble components. Now I realize that I may get torched leaving this question here, but believe it is worth it. This site has me fired up to get my Dad's old 1960 Allis Chalmers riding tractor rolling again. Thanks in advance for your help!
I have a Quantum Xm 60 model cms14012/Hr 2 press machine power pack many years ago working good but now it is not making pressure plz guide me
thanks share this video
Consulta la luz de valvula que medida lleva
What's the total time for a rebuild for someone with decent mechanical skill but new to this process?
if you have all the parts and just need to put it together I would say around 1 hour
@@francesthompson471 Wow!
I had that same engine and attempted to make it run on compressed air but incredibly failed
you didn't show us you putting in the valve springs...why not?
WHAT IS THE MAKE AND NUMBER OF SPARK PLUG. GREAT VIDEO....
Cj8 champion plug
I bought a gasket kit from sears and there's 2 head gaskets one's a little different anybody know why ?
this is the motor i have in my husqavarna lawn mower
i have two of these old engines i got one of them for free and the other one i bought for parts
these engines can make good go kart engines but you have to use a lawnmower trans axle
where can i find the other version with narration?
Taryl Fixes All
costo de la base del reactil
i didnt see any spring governor put on?
the piece that goes on the camshaft is the oil slosher or known as a govner
Good Job ! What was wrong with the engine?? Somebody run it without oil??? Most typical....did you change piston/pistonrings?? And finally, what is valve-clearanse: I and O?? Thank you, youtheman =)
hi what the eng. # on that one?
looks like the 890403
love the quantum
i have one :) its the model with the pull start coming out on the top and being geared
@@TurboTFM this is an L-Head Side Valve Engine right Not OHV or OHC?
@@adamsturdevant9250 yup
Picked up one the other day, goes good just needs a new spark plug I think but might do some more work just for the fun of it
i think the reason mine wouldnt run is bad head gasket and no spark
the flywheel key was fine and the carb bowl was clean
Doubt it would of been the head gasket, most likely bad coil or spark plug, jets blocked or a valve problem
Nice video! How many inch pounds on the head bolts?
Mine are 140 lbs I bought a gasket kit from sears and there's 2 head gaskets one's a little different anybody know why ?
144 "#
Очень много моментов пропущено
I just came here for the music.
Believer Silent Partner 1st song.
i want to make a steel camshaft for one of these so the engine could last longer
I've never found one with a damaged cam
I feel mislead .....
You should clean it up better it looks like crap
Cracking engines better then the weak crap out there today...
It would make more sense if you explain what you're doing
clean up that block its horrible
Херня какая-то