Just picked up a 1953 Golden Jubilee, been watching ALL OF YOUR VIDEOS your Daughter is AWESOME and i like her talks to the point, you definitely are blessed ! GREAT JOB TO YOU BOTH
I did this repair/swap on a 1939 Ford 9N whose hydraulic Piston wouldn't hold much even when operating. Swapped in an NAA Piston with rubber ring/wiper. Holds like Gibraltar now.
I don’t even work on tractors but I appreciate the clear instruction and good video. I wish you and your dad repaired thr printing equipment I work on.
You folks are the greatest. Thanks for the videos. One idea I have for a video would be a remote hydraulic setup for the NAA including possibly Hydraulic top link. I can only imagine there are plenty of people like myself that wish they could tilt an implement without getting off the tractor. Anyway, thank you guys for sharing your knowledge.
As usual. Thanks for the great video. I think my 600 needs this so Ill lok for that one. Can tou tell me if you have a video on a 600 series ford on adjusting the governor??
Thanks. I have a 1963 ford 4 cylinder 2000. Do you sell a video or manual for the hydraulics on it like this or does this also apply to the 2000? BTW all the parts I have bought from you guys, as well as the How To on rewire on ignition-starter-neutral safety switch is perfect.
Do you sell the pin that prevents the piston from coming out.. Not sure what its called.. Believe when the piston comes out it hits the pin to keep it from building pressure
Great content. I am very new to farming with some raw land and looking to purchase one of these older Fords. Does anyone recommend a good spot to make sure I don’t get ripped off and or a good broker?
I opened the top lid on my golden jubilee where is the pickup tube supposed to go off the acorn nut mine is kinked and don't see where it is supposed to be
Finding parts has become difficult. The Carb i currently have has one tag on it. So i ordered a rebuild kit off that tag. It was nothing like what i needed. So i used what i could and hand cut gaskets. The float that was sent was was small. So i had to use the old float. So thinking of replacing carb so i can get the tractor running and have a matching carb. @ShainAndrews
Just picked up a 1953 Golden Jubilee, been watching ALL OF YOUR VIDEOS your Daughter is AWESOME and i like her talks to the point, you definitely are blessed ! GREAT JOB TO YOU BOTH
Love watching these repair videos. We always learn so much!
I did this repair/swap on a 1939 Ford 9N whose hydraulic Piston wouldn't hold much even when operating. Swapped in an NAA Piston with rubber ring/wiper. Holds like Gibraltar now.
I just want to Thank you Rachel for the video's and you were such a big help walking me through step by step on my tractor. Thank you!!
I don’t even work on tractors but I appreciate the clear instruction and good video. I wish you and your dad repaired thr printing equipment I work on.
You folks are the greatest. Thanks for the videos. One idea I have for a video would be a remote hydraulic setup for the NAA including possibly Hydraulic top link. I can only imagine there are plenty of people like myself that wish they could tilt an implement without getting off the tractor. Anyway, thank you guys for sharing your knowledge.
This is a beautiful way to make a tractor.🌺
Just ordered all the stuff to repair the hiccups, nice to have all the parts I needed on one site!
Another well instructed how to video from a beautiful lady
The talented Tractor girl, well done!
As usual. Thanks for the great video. I think my 600 needs this so Ill lok for that one. Can tou tell me if you have a video on a 600 series ford on adjusting the governor??
Hello would you all ever consider doing a video for PTO shaft seal and bearing replacement for Ford 3000’s?
This woman is a better mechanic than i am and i have teaes experience
And shes beautiful great job to your dad i salute you sir
Beautiful video and work in mechanical engineering 🌹🌹
Thanks. I have a 1963 ford 4 cylinder 2000. Do you sell a video or manual for the hydraulics on it like this or does this also apply to the 2000? BTW all the parts I have bought from you guys, as well as the How To on rewire on ignition-starter-neutral safety switch is perfect.
Do you have vdo on jubilee rear axle seal replacement. I will be ordering parts from u love these vdos
Is the seal at 4:42 the "back pressure control seal" as I did not see another one listed?
I took the top lid off without removing the acorn nut, what did I mess up?
Also wondering about this.
Me too
As always, very informative.
This woman is the bomb
Just got an NAA. The lift arms raise the brush hog, but drift diwn slowly when tractor is off. Is this as it is supposed to? Great video btw.
good job
Do you sell the pin that prevents the piston from coming out.. Not sure what its called.. Believe when the piston comes out it hits the pin to keep it from building pressure
Great content. I am very new to farming with some raw land and looking to purchase one of these older Fords. Does anyone recommend a good spot to make sure I don’t get ripped off and or a good broker?
Ford Jubilee 600. Got it for free, and it has a 12v conversion. First start in 8 years; what size battery is recommended?
I opened the top lid on my golden jubilee where is the pickup tube supposed to go off the acorn nut mine is kinked and don't see where it is supposed to be
What do you recommend carburetors wise for my Ford 901 Powermaster. 4 cyclinder gas tractor? Adjustable front axle?
It isn't that easy. There are two or three versions.
Finding parts has become difficult. The Carb i currently have has one tag on it. So i ordered a rebuild kit off that tag. It was nothing like what i needed. So i used what i could and hand cut gaskets. The float that was sent was was small. So i had to use the old float. So thinking of replacing carb so i can get the tractor running and have a matching carb. @ShainAndrews
Where can I buy all the replacement parts
Which tractor had live Hydraulics and live pto
I have a super a the hydraulics are jerking on. Would I need to do this service on it?
Been looking have manuals on jubilee but cant find out how to service steering gear box. Please help
I have coolant in my oil jubilee engine, think it’s a head gasket? It was overheating, water was dropping fast
Sweet
how to do 8n steering box
I like smart people. 🥳 Thanks.
I am a tractor mechanic and lathe technician looking for a job opportunity
You can fix my 8N anyday baby xoxox❤