i fixed my clutch it was very tough to press down on after fixing it to the default position my clutch doesnt progress it only detects 0% to 100% in the software. did someone sell me a broken clutch pedals? the seller attached the clutch in the wrong position so i could check whether the clutch is broken or not
HI, I only partially agree with your modification. It is correct to increase the washers to 3 in order to raise the load cell and allow greater bending, but placing a third row of washers between the 2 a little further forward is not good because this significantly reduces the bending of the load cell and the result is that after 40 or 50 kg of applied force the cell no longer flexes as it should, significantly offsetting the measurement. I'm telling you this not theoretically but precisely because I tested it on my Cammus LC100.
it might be because I use higher force than you do. I went with 3 washer 2 column before in my first video but after sometime the washer cannot withstand the force and start deform. So the whole loadcell tilt and make the travel short again. SO I added a third column just like you seen in this video. even tho the pedal is a bit stiffer and shorter but for GT and F1 car it work really well. and it still work well ever since. Brake pedal is something that you need to make it your own. anyway if it work it work. Anyway Thank for sharing!
are you not able to register the full force available to the 100kg loadcell censor without tweaking? if so, can you tell me how much of the difference the tweaking makes to the peak force for the censor?
How’s sim racing scene in Thailand Bangkok ? Are there shops that sell sim racing gear like moza ? I may get a moza ecosystem or something in future direct drive I’m from india here there’s only g29 and t300 available , if someone goes to Thailand can they get this gears ? Language barrier is also a issue . People don’t understand English primarily in Thailand from what I assume
Thanks for the video! I have 2 questions. 1. Is there a way to change the brake linearity? I'm loving my ones but i would like it to be a bit more sensitive when i first press them. 2. What does raising the loadcell ball do?
1. in cammus software you cannot do anything with pedal linearlity (as far as I talk they are working on brake linearity). Right now you can only set min-max in the app. But some game will let you tune brake linearity AKA brake Gamma. 2. if the loadcell ball is too low it will limit your pedal travel. hence you cannot push more value into your loadcell. You can see it as pedal stopper.
@@BoreyEngineering Hey there! I've installed the new update for the pedals but I can't access the brake curve. Do you know why this might be happening?
@@racingmaster45 I cannot access the brake curve too! I have try it on both Cammus LC100 and Cammus CP5 pedal. I have already report this to Cammus and it seem to be a bug. Hope they will fix it soon.
I have a problem with the throttle pedal. When pressing it more than 80% the input value jumps to 0. I have already tried playing around with the calibration in the Cammus software but none of that worked :( Does someone know anything about that?
what connection do you use? To wheel base or USB to PC? You can try swap your connection and try again. You can ask in cammus discord for better support discord.gg/ChSB4Qap8T
@@revalix6778 it will not work if you connect in to moza. You can try connect it to other computer and see if the result are the same. USB 2.0 and 3.0 port might make a difference
unscrew the sensor on the bottom of the pedal and you will probably see some metal schreded from the missing flat washer...the magnet is probably full of shreded metal and giving bad calculation...mine have does that afer 1 week and i managed to repaired it easyly by just drill the hole a little wider juste for the bolt stop to hit all around the hole, now im 1 year later and never see this problem again, next time i manage to add flat washer everywhere to eliminate the left right loose of the mecanism, i have one pedal set from one of first batch sended to canada, when i recieve these i ddnt know was with load cell cauz it was before the reveal online of these new pedal set
I'm still running it daily. the only annoyance is when they update steering wheel firmware. The wheel parameter seem to change a lot that you need to retune you wheel every firmware update. Apart from that I don't have any problem at all
@@attha2 No. They not using hall sensor. They use loadcell to measure all 3 pedal. But in Gas and throttle pedal they config it in the way that measure pedal distance instead of the force apply to the pedal.
![CAMMUS LC100 (V2) Pedals [REVIEW] These SIM RACING PEDALS are hard to ❤️](http://i.ytimg.com/vi/RcWB2Luxomg/mqdefault.jpg)
![CAMMUS LC100 (V2) Pedals [REVIEW] These SIM RACING PEDALS are hard to ❤️](/img/tr.png)
i fixed my clutch it was very tough to press down on after fixing it to the default position my clutch doesnt progress it only detects 0% to 100% in the software. did someone sell me a broken clutch pedals? the seller attached the clutch in the wrong position so i could check whether the clutch is broken or not
Hello, thank you for the video. What height the ball bearing comes out de loadcell switch after ajustement?
The loadcell ball is not glue to loadcell so you can just grab it and take it out. but you need it to adjust the hight
why did you switched from your sim jack?
great video. Thank you. I have the LC 100 pedals. how do i make the brake throw longer? it feels so short
The brake throw is unfortunely got limit by the damper throw. You need to remove damper OR make damper rod a little longer to add more throw
@@BoreyEngineering ahh ok I understand. Thanks for responding. After using them for a bit I don't mind the.short throw. I just need to keep tuning.
HI,
I only partially agree with your modification.
It is correct to increase the washers to 3 in order to raise the load cell and allow greater bending, but placing a third row of washers between the 2 a little further forward is not good because this significantly reduces the bending of the load cell and the result is that after 40 or 50 kg of applied force the cell no longer flexes as it should, significantly offsetting the measurement.
I'm telling you this not theoretically but precisely because I tested it on my Cammus LC100.
it might be because I use higher force than you do. I went with 3 washer 2 column before in my first video but after sometime the washer cannot withstand the force and start deform. So the whole loadcell tilt and make the travel short again. SO I added a third column just like you seen in this video. even tho the pedal is a bit stiffer and shorter but for GT and F1 car it work really well. and it still work well ever since. Brake pedal is something that you need to make it your own. anyway if it work it work. Anyway Thank for sharing!
are you not able to register the full force available to the 100kg loadcell censor without tweaking? if so, can you tell me how much of the difference the tweaking makes to the peak force for the censor?
if you don't tweak the pedal is not usable in my opinion. it's too light hence also make resolution so poor
Is it just me or all the V1 pedals don't have the curve visible in cammus software?
i will not have curve adjustment
How’s sim racing scene in Thailand Bangkok ? Are there shops that sell sim racing gear like moza ? I may get a moza ecosystem or something in future direct drive
I’m from india here there’s only g29 and t300 available , if someone goes to Thailand can they get this gears ? Language barrier is also a issue . People don’t understand English primarily in Thailand from what I assume
There are plenty of Sims shop in Thailand. if you want moza you can visit "simple sims racing" they are distributor in thai
Thanks for the video! I have 2 questions.
1. Is there a way to change the brake linearity? I'm loving my ones but i would like it to be a bit more sensitive when i first press them.
2. What does raising the loadcell ball do?
1. in cammus software you cannot do anything with pedal linearlity (as far as I talk they are working on brake linearity).
Right now you can only set min-max in the app. But some game will let you tune brake linearity AKA brake Gamma.
2. if the loadcell ball is too low it will limit your pedal travel. hence you cannot push more value into your loadcell. You can see it as pedal stopper.
I can confirm now that the brake linearly is coming soon!
@BoreyEngineering Thanks for confirming! I just had to get used to it, but being able to change it will make it much better!
@@BoreyEngineering Hey there! I've installed the new update for the pedals but I can't access the brake curve. Do you know why this might be happening?
@@racingmaster45 I cannot access the brake curve too! I have try it on both Cammus LC100 and Cammus CP5 pedal. I have already report this to Cammus and it seem to be a bug. Hope they will fix it soon.
I have a problem with the throttle pedal. When pressing it more than 80% the input value jumps to 0.
I have already tried playing around with the calibration in the Cammus software but none of that worked :(
Does someone know anything about that?
what connection do you use? To wheel base or USB to PC? You can try swap your connection and try again. You can ask in cammus discord for better support discord.gg/ChSB4Qap8T
@@BoreyEngineering okay thank you very much! Im gonna try that
@@BoreyEngineering I currently have it connected to the PC via USB. Will it work if I connect it direc5tly to a Moza R12 wheelbase?
@@revalix6778 it will not work if you connect in to moza. You can try connect it to other computer and see if the result are the same. USB 2.0 and 3.0 port might make a difference
unscrew the sensor on the bottom of the pedal and you will probably see some metal schreded from the missing flat washer...the magnet is probably full of shreded metal and giving bad calculation...mine have does that afer 1 week and i managed to repaired it easyly by just drill the hole a little wider juste for the bolt stop to hit all around the hole, now im 1 year later and never see this problem again, next time i manage to add flat washer everywhere to eliminate the left right loose of the mecanism, i have one pedal set from one of first batch sended to canada, when i recieve these i ddnt know was with load cell cauz it was before the reveal online of these new pedal set
Hey im looking for the best pedal set under 250 dollars and this is on sale, should i buy it or is there other recomendation??
Well every pedal at this price point have it's weakness at something. but for me I skip simjack because for the tempeture inconsistancy.
what is cammus lc weakness, and did they add ability to change the brake linearity? @@BoreyEngineering
@@anasa8877 They already add the ability for CP5 now and tonight I will check if the add it to LC100
How is your experience with Cammus product so far?
I'm still running it daily. the only annoyance is when they update steering wheel firmware. The wheel parameter seem to change a lot that you need to retune you wheel every firmware update. Apart from that I don't have any problem at all
i like your content. which game are you playing? iracing?
AC, ACC, Dirt Rally 2.0
@@BoreyEngineeringi saw you were using simjack. are they using hall sensors?
@@attha2 No. They not using hall sensor. They use loadcell to measure all 3 pedal. But in Gas and throttle pedal they config it in the way that measure pedal distance instead of the force apply to the pedal.