it depends on the car like mercedes when they get in an accident the fuse in the front of the hoods pops to avoid electrical shorts that can cause a fire.
how do you know what chip to read? I have a 2014 hyundia sonata module number 95910-3q150 with eeprom chip 95256 but there are a few chips that look like they could be it.
yea the same program makes everything read first save the file and then select the saved file to be corrected and the program will clear it and save it and then go back and select the cleared file and then write it back to the module
Is this why my ford ficus will not crank after i hit an snimal that was in the road. The car cut iff snd messages are coning up that say engine starting fault or somrthing like that. Hill assist not available and no key detected. Forscan will not comnect to vehicle rither
I don't think so. your problem might be a short to the CAN communication lines in your car probably when u hit the animal it broke cables and that's causing your problems
Thanks for the share, I really wish you all the success in your journey. You give the best description possible it could. Grate work man 💯💯💯
Thank you! You too!
many thanks. short and to the point
thanks for visiting the channel
Great video,thanks for the software.
no problem
Thnx! A good clear video
No problem
Hello hope you are doing well I have been watching this for 3 months and was asking can it do Toyota’s
yea it work on toyotas too.
Great video, and thanks for the software.
thanks for watching
it's OK if you have or use scanner alot, but for one off better sending it away or use forscan
yea or just get a used one that is not crashed
Great video!! Where did you get the Autel software for your laptop??
the software is in the autel website under downloads
Thx for sharing javier 🌹🌹🌹 , Does the airbag service tool need the Internet to work, or does it work without it?
no internet needed. u just have to create an exemption on windows virus or it will erase it because it sees it as a virus but it's not.
Very interesting what you do.Thank you
thanks
Do i have to fix the car first in order to fix the crash module or does it don't matter
it does not matter
How would I know which models can and can’t be reset? Is there a list somewhere? Thanks!
here is the website i use. hope it helps u.
www.tachosoftonline.com
Will this cause a car not to start after a crash starter fluid in throttle body not working
it depends on the car like mercedes when they get in an accident the fuse in the front of the hoods pops to avoid electrical shorts that can cause a fire.
I got it to start bad intake gasket had water in cylinders new sparkplugs fired right up
hi, thanks for the video, do you know in mk2 model where is that airbag module? it is in the same place than there? thanks
yea I believe it is the same too on your model
Thanks a lot but can u tell me how to download autel software on pc and after downloading the reset app it asks to do update csn we do that
if u open the reset app do not update it.
@@JVFIXLLC and how about autel app to read eeprom
here is the link. www.autel.com/download.jhtml
u need to download the maxi pc suite
how do you know what chip to read? I have a 2014 hyundia sonata module number 95910-3q150 with eeprom chip 95256 but there are a few chips that look like they could be it.
the program specifies the chip and I read the numbers on top with a microscope. or use your phone to zoom in
So how it works is Program A reads crash data/Program B makes corrects crash data/ and program A writes the corrected data into the module?
yea the same program makes everything read first save the file and then select the saved file to be corrected and the program will clear it and save it and then go back and select the cleared file and then write it back to the module
Nice video thanks how much do you change for that service
thanks for watching. for this job is 150
Excellent Thanks!
thanks for watching
Great video you shared
Thank you
thank you
Is this why my ford ficus will not crank after i hit an snimal that was in the road. The car cut iff snd messages are coning up that say engine starting fault or somrthing like that. Hill assist not available and no key detected. Forscan will not comnect to vehicle rither
I don't think so. your problem might be a short to the CAN communication lines in your car probably when u hit the animal it broke cables and that's causing your problems
Hello 👋
Have have read the file with my im608 pro. Any help on how to clear the crash data? Thank you
yea download the program it the link I left in the description. that will clear the data
I had a crash on my car, the seat belt locked. If i reset, the seat belt release or need a new one ?
u will need a new seat belt
I love your videos
thank you for watching
hello i downloded the software from the link but the software crash every time i open it, any special procedure to install or something? thanks
what operating system are you using?
how do i download the program just keeps opening a blank tab
just click on the blank tab
Good Job man 👨 👏 👍
thanks and thank you for watching
Can i used autel mk808bt pro? And just buy the programming tool?
i am afraid you can not that scanner is only for obd2 bidirectional controls only. you need an actual programmer that can read eeproms
@@JVFIXLLC for example?
@@Eduardo-vv6lm orange5 is a really good one
Thanks!
thanks alot!
Great tutorial,you went straight to the point with no BS,thank you
Exellent😊
thank you
Hi
Thank you for the video. Unfortunately i can't see the download link for the software
the link is there i think you are watching from your phone and it does not show it but the link is up and u can download it.
nice thanks
thanks for watching
Can u do it without taking out the module?
no. u need to remove the module and open it.
I can I get this app
yea I have it for sale. for what car do you need to it?
A very informative video. Thanks
thanks you.