i am a arc welder..this is my firs time to see vertical down ward welding,i try like this technique,i think it so difficult but i try. you use E 6013 ORDINARY welding rod but you done in good way..thank you for sharing ..
That's bullshit. Vertical down is nothing more than cosmetic, no strength in it at all. Do not do it. Only pipelines should weld vertical down - and that's an entirely different procedure.
Все правильно !!! Сверху вниз без манипуляций !!! потечет металл с о шва если водить элэктрод со стороны в сторону . И конечно ток по толщине металла . тип элэктрода ну и его влажность + напряжение в сети ...
Essa segunda solda descendo e permitida numa chapa dessa espessura e com eletrodo e 6013 por eu acho que tem que ser solda acendente e com eletrodo 7018 de 2,25
Yukardan aşağıya rutil-selülozik yani rc elektrotla yapılabilir.düz bir şekilde salinimsiz kaynak yapılır.rr rutille olmaz.dediginiz gibi dikkaynak yapilir
Verdade. Tem muito "professor" de solda que não sabe fazer uma solda bem feita assim. Mas tenho minhas dúvidas se essa última foi feita mesmo na vertical porque se vc prestar bem atenção a poça de fusão atrás da solda não escorre. Se foi mesmo soldada na vertical, parabéns.
La soldadura descendente aprendí que se usa en metales delgados y para la homologación solo en el primer pase con el chaflán hecho en el material se utiliza la soldadura descendente.
@@MambinSin no, you don't touch the the plate unless you're using 7024 rod. you can just jam push that rod in and drag it, but for 7018 rod you can't do that.
The down hand fillet weld(1st one) didn't have enough amps, the weld bead is distinctly convex, and there's undercut along the upper toe; the second weld, 'vertical down' or 'stoving' as it's known is bad wherever it's encountered, don't do it, Pipeline welders do it on 'low pressure' pipework, and where it's buried in the ground: high pressure situations, structural work is up! Up! Up!
thank you for your video Iam begginer and hope learn arcwelding when welding all welder weaves but when you weld down in this video why dont you weave what's the difference with weaving or not
Muy oscuro el cordón y tiene salpicaduras la pieza. Tampoco he visto que se limpien las piezas a soldar, ni que se calienten los electrodos a utilizar....
@@diegomengoni3494 The first weld was a 7018, second one was 6013. On the second weld, a 7018 run UPHILL would be much more appropriate for that thick of plate! Nice looking downhill bead though!
Perfect rod angle?? Uhhh, a 45° angle to a 90? Wow!!! Try flat turn diagonal then uphill wrap at 90, overhead turn down hill and meet your first 1F start. No X-ray. But visual. Although it get pressed to see how much pressure it takes to break certain sections. This test isn't traditional and they select coupons to test based on visual. But you aren't told that ahead of time.
Salam brother. Please brother local made welding machine ki electric wire ko lagane ka tareka bi bta do. Kaise lagate hai wire aur welidng karnr keliya ready karte hai.
i am a arc welder..this is my firs time to see vertical down ward welding,i try like this technique,i think it so difficult but i try. you use E 6013 ORDINARY welding rod but you done in good way..thank you for sharing ..
Voltage machine kie kitne hone chye
That's bullshit. Vertical down is nothing more than cosmetic, no strength in it at all. Do not do it. Only pipelines should weld vertical down - and that's an entirely different procedure.
Parabéns professor um belíssimo filme de responsabilidades em segurança para nossos olhos!?
수직용접시에는 아래에서 위로 올리는 걸로 배웠는데요 위에서 아래로 내리면 용접물이 흘러내려 빨리 내려가야 하기 때문에 두 모재가 완전히 녹아 붙었다고 볼수 없읍니다
It depends on rods
You can weld uphill downhill if your rod supports it like 7018
Do you have 7018 rods in Korea ?
No metalon é mais difícil. Desse jeito até eu passo na prova. Mas todas dicas são importantes. Valeu
Nao e bem assin nao amigo!!
Nasty Dimes....GREAT JOB..👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿
Все правильно !!! Сверху вниз без манипуляций !!! потечет металл с о шва если водить элэктрод со стороны в сторону . И конечно ток по толщине металла . тип элэктрода ну и его влажность + напряжение в сети ...
вертикал варится строго снизу вверх!!! тут важна не красота, а катет. у него металл десятка, и ее нужно проваривать с катетом, чтобы *полка * была.
Essa segunda solda descendo e permitida numa chapa dessa espessura e com eletrodo e 6013 por eu acho que tem que ser solda acendente e com eletrodo 7018 de 2,25
Kaynak pozisyonu ve parca dik pozisyonda olduğundan yukardan aşağıya kaynak olmaz sadece sıvama olur aşağıdan yukarı dik kaynak yapılır
Yukardan aşağıya rutil-selülozik yani rc elektrotla yapılabilir.düz bir şekilde salinimsiz kaynak yapılır.rr rutille olmaz.dediginiz gibi dikkaynak yapilir
Exllent job 👌👌👌👌
My hat is off to you for your welds. Just like a painted picture. How well is the penetration of the weld ???
0% penatration on the vertical down
@@jimmartin9704 How do they test penetration on vertical welds Jim ??? Peace. V
Nossa é a primeira vez que vejo uma solda tão bem feita nessa posição com eletrodo
2 posição
Verdade. Tem muito "professor" de solda que não sabe fazer uma solda bem feita assim. Mas tenho minhas dúvidas se essa última foi feita mesmo na vertical porque se vc prestar bem atenção a poça de fusão atrás da solda não escorre. Se foi mesmo soldada na vertical, parabéns.
@@JoseEmidiojsemidio bem obiservado
Também achei pois no 6013 nessa posição muito difícil nao escorrer a solda muito bem feito!!!
Excellent video...Thanks for sharing
At what amperage do you run the vertical?
Nice 👍👍👍
Che bella saldatura, complimenti. Fossi capace io a farla così.
Hmmm ... downhill 6013 looks like slag of fusion ! 😆
Arc Length, Perfect 🔥🔥🔥
Попробуй тонкий метал вертикально ,ещё российским элэктродом )))
нормально вариться российскими электродами
да не важно какой металл. вертикал варится снизу вверх. а этого сварщика в первом же учпункте пошлют на хер.
Wow👏 greetings from Finland
La soldadura descendente aprendí que se usa en metales delgados y para la homologación solo en el primer pase con el chaflán hecho en el material se utiliza la soldadura descendente.
Perdon mi ignorancia, que es el chaflan?
@@rn1238??????? 🤣🤣🤣🤣🤣
@@rn1238 bisel
La vertical en 6013 la soldó de forma ascendente y me queda bien
Dificilmente vc vai fazer teste de solda em metalon . Só se for em serralheria e olhe lá. No resto é fogo alto .
Nice guru khadi welding hmse gir jati he kese krni pdti he jrur btaye
لحام التنازلي ضعيف وغير مقبول للسماكات الكبيرة نسبة غرز مافيو ابدا
Chỉ sắt tôn dày thì hàn kiểu gì cũng được. Bạn thử hàn với sắt tôn mỏng o.8.và 1 ly xem sao.
Good 👍👍👍👍🇪🇬🇪🇬🇪🇬
Aprendi 100% a soldar foi nesse canal
Fico feliz em ouvir isso
@@iron9844 assistindo aqui do Brasil
Bro porque no soldas de abajo asía arriba
6013 downhill makes a good looking weld, but I wouldn't use it for thick objects like this...
Good but main problem is thin metal 20 gauge pipe welding sheet will be melted and damage
Hi engineer Is it possible to show us a video on how to weld the bottom part of a structure
Plzz tell me what is the catagory of welding channels
Some say there is no strength in your welding , would you prove them the contrary.And why they say that ?
Dik aşagıya hangi elektrodu kullanıyorsun ustam
Nice work sir!
Do you tip the rod head sitting on the plate while u welding? Or there is a little gap in the arc length?
I have the same question about touching plate while welding
@@MambinSin no, you don't touch the the plate unless you're using 7024 rod. you can just jam push that rod in and drag it, but for 7018 rod you can't do that.
you can increase arc force and touch the plate swiftly , the main point is the arc need to be damn tight for vertical
Hi. Please make one video how to fix electric wire and then start welding.
Hi
วิธีตกแต่งบ้านให้สวย
Nice
The down hand fillet weld(1st one) didn't have enough amps, the weld bead is distinctly convex, and there's undercut along the upper toe; the second weld, 'vertical down' or 'stoving' as it's known is bad wherever it's encountered, don't do it,
Pipeline welders do it on 'low pressure' pipework, and where it's buried in the ground: high pressure situations, structural work is up! Up! Up!
thank you for your video Iam begginer and hope learn arcwelding
when welding all welder weaves but
when you weld down in this video why dont you weave what's the difference with weaving or not
if you need bigger fillet , you weave to save time,, and make the fillet broader
👍👍👌👌
Siempre para arriba en posición 3g
Good job bro
How many amps is the current. Thank!.
can you show it on thin square pipe
👏👏👏👏👏 excelente!!! Cual seria la potencia??
Anda a saber, si ni lo mostró
6013 1 means all positions vertical up
Please mention power output
Pls tell me power and amps adjusting for good welding
Amazing.. 🙏🙏👌
Muy oscuro el cordón y tiene salpicaduras la pieza.
Tampoco he visto que se limpien las piezas a soldar, ni que se calienten los electrodos a utilizar....
Yo I just started welding and I am good at welding at anangle with the 12 rod but bad with 10 rod what am I doing wrong
Itu mah api pas besi tebel, cb yg tipis dan bukan sudut tp agak renggang msh gitu kah sudah pasti engga
Cakep bnget las turun nya kawan
сверху вниз варит да, красиво но тонко, и хуже вплавляется в центр, на не ответственных конструкциях пойдёт но лучше пройтись также и второй раз
Металл 10мм где с таким сталкивается любитель?
What is the weldig current
Boa noite Amigo! Qual é a amperagem?
You are amazed thank you very much!
Good video thanks sir for that
Sir aap mujha welding sekha skta h
👍👍👍👍👍
Lovely layering..
how many amper are you using?
Que tipo de electrodo es ?
@@diegomengoni3494 6013 electrode
@@diegomengoni3494 The first weld was a 7018, second one was 6013. On the second weld, a 7018 run UPHILL would be much more appropriate for that thick of plate! Nice looking downhill bead though!
Good morning welding
Perfect rod angle?? Uhhh, a 45° angle to a 90? Wow!!! Try flat turn diagonal then uphill wrap at 90, overhead turn down hill and meet your first 1F start. No X-ray. But visual. Although it get pressed to see how much pressure it takes to break certain sections. This test isn't traditional and they select coupons to test based on visual. But you aren't told that ahead of time.
Bonsoir du 2.5 6013 combien l ampères montante et descente merci sinon très belle prestation
Great video. I like it! 200% :-)
nice
Pero cuanto amperage debo poner la máquina de soldar
espessura do material ?eletrodo diâmetro do eletrodo?
ممكن اسم ماكنة للحام وعندي مشكلة من الحم يقطع
Current kitna rakha thha ye likhe nahin sir
Compañero ninguna soldadura en descendiente está homóloga por lo tanto esa soldadura no tiene la resistencia que de llevar
Perdon mi ignorancia, sabes porque no esta permitida?
На толшину метала посмотрите 😂😂😂😂 я на 2,5 так же варю
La primera está cruda le falta un poco más de amperaje
Cantik cantik very beautyful
itu di amper berapa bapak
Thanks 😊
good job.
رجاءً اكتب رقم المكينه حرارتها
Thank yuo
Salam brother.
Please brother local made welding machine ki electric wire ko lagane ka tareka bi bta do. Kaise lagate hai wire aur welidng karnr keliya ready karte hai.
no matter how hard I try to do it according to your instructions, I still can't achieve your result and it looks terrible :-(
Why in the hell would you weld top to bottom, no strength in that weld at all,
Especially with very thick metal.
Please explain why? Am learning..
Needs more penetration for good strong weld thats why weld up (vertically).
There is strength there bitch...im a welder myself amd this is work
Vertikal pozicion ,,⬆️
Ma la seconda saldatura è all'americana , e non dal basso in alto.
you have undercut in this welding!
Don't judge brother
Master welder🤝🇮🇩🇮🇩🇮🇩
The stick is good,we can't welding from up to down
Amos?
เหล็กหนาแบบนี้เชื่อมง่าย
E 6013 RC?
कारण कितना था!?
grazie .super 👍👍
Хороший элэктрод, не то что наша гавно
I used to make it from top to bottom, but he had a problem, because it was liquid ,,, 😂
Please 5g welding pipe and plate
在68年代我們焊接電焊的科技都用人頭腦神經感覺焊件燃燒的聲音就知電極💋强弱鐵水熔化作品平💋坦魚磷片，護目鏡下注意鐵水💋流程及焊條熔化💋的速度。
कारण कितना था!
Ну такой толстый металл на большом токе легко варить.