HPI Rush Evo T15 Engine What's The Problem?

Well I found the problem!
My Amazon Wish List www.amazon.co....
Join this channel to get access to perks:
/ @haggardrc
Please check out my Wish list and anything you may send me will leave me eternally grateful ;)
Rusty's Amazon Wish List: amzn.eu/3TJm7Rf
You can help me make better content by donating Via PayPal as a gift to [e-mail]!
Or you can use this link: paypal.me/Rust...
Every penny that is donated will go into making good quality videos for all my loyal subscribers!
Many thanks to you all :)
#NitroRC #RCCars #HPiRush

[@kenwalters845]

You have the wrong plug... you need a standard short plug... that's a long plug... the plug when installed should NOT protrude into the combustion chamber...

[@Gt403cyl]

I was going to say this, but noticed someone else did!

[@InVerticalDamage]

That's exactly what my new glow plug did. Lit up just like that one but take glow starter off and it's shuts off. Sometimes it idles 2 or 3 secs after glow starter off and then shuts off.

[@lyndonwebber1389]

If you hot that copper washer up drop it in water, it will soften it again allowing it to make a better seal, or let it cool slowly naturally.

[@kelvinhopes8410]

Annealing is the process. Although with copper you need to quench in cold water when it's hot.
Steel hardens when dropped into water and remains soft if air cooled. Copper works the opposite way so when air cooled it HARDENS and when quenched it will stay soft, which is what you want for its sealing properties. Although with copper washers this small probably doesn't matter :)
I do this for nearly every oil sump plug that the customer can't be bothered to pay a quid or 2 to replace 🤣🤣🤣

[@lyndonwebber1389]

@@kelvinhopes8410 you said it better.

[@HaggardRC]

That washer wasn’t worth a wank lol

[@InVerticalDamage]

Just burnt up my clutch bell bearings trying to get through the third tank and notice the bearings are now just washers. Metal shavings everywhere lol

[@HaggardRC]

That’s Alright I ran for years without any bearings at all

[@InVerticalDamage]

@@HaggardRC how you do that I thought you need bearings to take the slop out of CB

[@HaggardRC]

You do, it was flapping around like crazy but still worked alright lol.

[@InVerticalDamage]

@@HaggardRC lmao wow impressive

[@InVerticalDamage]

@@HaggardRC did you make the hole bigger on CB since no bearings? Pretty much had to throw it away after huh

[@Gt403cyl]

I think you forgot to re-install the copper head shim as well.

[@henryfoster3212]

A good to day hold a lot of people with day rc have good 👍day tank you 💯🔧

[@mikeymike3240]

Judging from those symptoms it needs a new piston and liner 😮

[@bergan1227]

New sleeve and piston needed maybe

[@therccelebrityspeedfresh5393]

Change that glow plug man

[@therccelebrityspeedfresh5393]

Oooohhhh cccooommmmeeeeee ooooooooooooonnnnnnnnnn.

[@HaggardRC]

You know dude

[@therccelebrityspeedfresh5393]

@@HaggardRC I’m trying to get it start it man

[@kelvinhopes8410]

Had the same issue with my MT2 that I keep mentioning lol.
Just repinched the sleeve as there was practically no pinch left (quarter of the piston could make its way out the top of the sleeve).
It still ran like this but wouldn't idle properly when hot or tune properly :)
Same engine as this - the original t-15. What's your thoughts on these engines, worth an upgrade? Keep eyeing up the HPI G3.0 to chuck in the old thing haha

[@kelvinhopes8410]

Also good to see someone that's "old school".... unless it's really critical (car engine head bolts, cam caps, big end bearings etc) I don't use a torque wrench at all...
Common sense, loctite when needed and do things up properly... never had a problem 👌

[@HaggardRC]

That’s right I don’t torque up anything apart from head bolts and bearing caps. My hands know when they’re tight enough lol

[@carpertony5123]

I replaced my firestorms G3.0 engine with a new force 18 and put the old G3.0 into a rush rolling chassis. Took a bit of work to do it but it's in. For some reason though it never ran right and I got loads of pressure and bubbles in the fuel tank. It spits fuel out of the filler cap every time it's opened lol.

[@HaggardRC]

That’s good the more pressure the better

[@carpertony5123]

@@HaggardRC decent pressure is a good thing I know but that thing was like a volcanic eruption every time the tank was opened . For some reason I just couldn't get the needles set right. It never ran like it did in the firestorm. Might have to dig it out and play with it again and figure it out bro.

[@NoneNone-gk9wt]

Dont just run it tear it down and clean it

[@therccelebrityspeedfresh5393]

Your glow plug is out

[@HaggardRC]

Still? Hold on I put it back in soon.

[@alexgarrod9093]

Sent u messages bud