Hi thank you for the video... After reset memory i go to calibrate and the lights wont bling fast meaning it does not want to calibrate can you help me figure out why?
Salam, im from Indonesia, i do likes that on Camry HV 2011, do w/ thinkcar2 scanner and w/ GTS Toyota , but the both not solved yet. Kondition : Pump+accumulator has changed w new. d u have any clue ? thx b4
Ever figure this out I went through the whole procedure and bleeding with a Topdon scanner and C1345 and C1368 won’t clear. Installed used booster and pump doubt they are also bad 🤷♂️
@@johnshin4645, I ended up going new. The issue was the used booster. I then used my original booster and used accumulator pumps from the junkyard and was still hearing the pump run and run and run. I assume the booster had an internal leak or malfunction. I purchased new pump and booster from dealer at a rate of $1300 which is insane money and it calibrated fine. In short, I’d just replace with a new unit unless you can verify 1. The used unit is/was upgraded with the service campaign/bought new or that the used unit has under 100k or less (rare). The job isn’t fun and bleeding isn’t either. Not worth the time to do this 2-3 times.
Very helpful thanks brother
Nice video and very helpful ❤
If it dosen't finish the calibration you need a new abs unit from the dealer
Is the recalibration code for c1345 procedure the same on a 2007 toyota camry hybrid?
Thank you Sir for your video and response.
mashalla
Hi thank you for the video... After reset memory i go to calibrate and the lights wont bling fast meaning it does not want to calibrate can you help me figure out why?
in my case blinking stop half the way and calibration is not done, do you think is hardware or air in the system
I appreciate you, LETTTT'S FUCK!NG GOOOOO!!
But mine stops half way what could be the problem 😊
Salam, im from Indonesia, i do likes that on Camry HV 2011, do w/ thinkcar2 scanner and w/ GTS Toyota , but the both not solved yet.
Kondition : Pump+accumulator has changed w new.
d u have any clue ?
thx b4
What scanner did you use here?
Its launch 43q pro
After reset memory when liner soliniod offset not Learning r calibrating why ?? What is the reason
Then perhaps your accumulator pressure is low..
@@autoskills1476 so that can cause it not to clear
@@autoskills1476need to change abs motor?
Hello, you have a Toyota softwer?
Launch x431 pro
salam , what scannner model your scanner?
Launch x431 pro
Hello
I did a calibration on the C1345 code but it is still on the board. What can I check now?
I look forward to hearing from you.
Thank you
Ever figure this out I went through the whole procedure and bleeding with a Topdon scanner and C1345 and C1368 won’t clear. Installed used booster and pump doubt they are also bad 🤷♂️
@@JohnDoe-j7s2c bleeding air from every wheel caliber ?
@@johnshin4645, I ended up going new. The issue was the used booster. I then used my original booster and used accumulator pumps from the junkyard and was still hearing the pump run and run and run.
I assume the booster had an internal leak or malfunction. I purchased new pump and booster from dealer at a rate of $1300 which is insane money and it calibrated fine.
In short, I’d just replace with a new unit unless you can verify 1. The used unit is/was upgraded with the service campaign/bought new or that the used unit has under 100k or less (rare).
The job isn’t fun and bleeding isn’t either. Not worth the time to do this 2-3 times.
Can i communicate with you
00923118000345 watsapp
Bhai Urdu mein video bannao thank u
English international zuban he.urdu me bi videos available he.thank you