Siemens Simatic G120 parameters copy paste with BOP.

[@mayurI4188]

Very helpful video... Sir plc se drive me backup dalne ki procedure pe video banao

[@sonudanghi5777]

very helpfull video sir for industries

[@jhonatasferreiradealmeida5437]

Great explanation!

[@rishisrivastava2746]

Good vedio.can we note parameter manually and save in computer. Please make vedio

[@puneethynpuneethyn]

Thank you so much for this video sir

[@anupamkumar4440]

Sir dusri drive me parameters paste karne se pehle usko reset bhi karna hai ya nahi?

[@mingovazquez704]

Great video, very helpful, thanks.

[@deepakchandra5187]

Nice video
Much helpful

[@vienbui6194]

Thank you for video .thank you sir

[@janmejayanayak5047]

Bery very thanks to you.

[@musicart2516]

Very helpful video
Sir But muje problem a rhe hai
Parameters par cross ❌ a rha hai please help

[@sakshimankad2876]

Nice information

[@industryautomation6661]

Thanks

[@hermannnani7680]

Thanks a lot for this video

[@veereshh1824]

Dear Sir
G120 Drive Current is Fluctuations.
So we Checked Motor Found Okay and Motor Replacement also done but same Fluctuations.
So we replaced Drive and Checked Found Same Fluctuations.
And drive Input and output chokes Replaced same Fluctuations.
After this all replacement only one common Issue Current Fluctuations.
Motor Rating 75 KW
Full Load Current 131 Amps.
So kindly request you please suggest me as soon as possible.
In drive what I need to be Checked?

[@sagirmohammad7187]

Please tell me .When the motor speed is reduced, the motor turns upside down.

[@venkikarri5855]

Dear sir
Pm240e drive macro drive unit p0015 ka kaam kya hotahai
Agar default kya dhalna hotahai

[@MukulRajkumar-k6v]

Great 👍

[@GulabSingh-ng7xe]

Very nice

[@chandub523]

Ye copy paste karne se IP address copy nhi hota hai kya

[@nishanthempirecinemas]

brother mera pass v same drive hai ek par supply drive me 360 para meter dhik rah h, aur return drive bara bar kam kar rah h , ye jo problem program ka issue aur dhoosra plz answer

[@Chezhiyaniniyan]

Thank you

[@ashishjain3588]

F1662 fault in Siemens Sinamics PM240..please help

[@AkhileshKumar-cl2nk]

Thank sir ❤❤❤❤❤

[@trilochangahtori9801]

Great👍

[@janmalesela2510]

What the effect copy from.Ram to Rom

[@waseemakramdaula8033]

micromaster 440 siemens please sir make video 0 to 10 volts control and configure

[@SusantaDas-vb8we]

Simens drive analog output kayse karo

[@vijaypratapsingh2485]

Sir micromaster 440 ki drive par bhi video banao

[@vijaypratapsingh2485]

Sir micromaster 440 par bhi aisi video banao

[@electricalmanager3982]

Copy from one drive and past to another drive but BF alarm blinking. what is solution, both drive is online network.

[@industryautomation6661]

Alarm blinking because both drive is online network.first you check drive communication device ID and Enter the communication ID of both the VFDs separately.

[@zaheerahmadmuhammad1414]

Thanks Bro

[@jibanjyotibehura3565]

Hii sir in my VFD it’s not getting on by auto command, I need to press HAND Auto button then it getting run. So can you please help me to fix this issue. Seimens G120 VFD

[@sharifhossain8830]

Great

[@rajatpanwar4643]

Thx

[@saijagadeesh9]

How to change display sp 1742 t/ min to zero

[@MKSIDDIQUI-786]

Thanks

[@zubinbhavsar9645]

Fault 7900 Sahi kese kare

[@shariqm9761]

i need cu card cu250s-2

[@chetankumar1370]

Falt 7800 kaise sahi kre

[@industryautomation6661]

Motor over current.
Check the current limits (p0640).
Vector control: Check the current controller (p1715, p1717).
U/f control: Check the current limiting controller (p1340 … p1346).
Increase the acceleration ramp (p1120) or reduce the load.
Check the motor and motor cables for short-circuit and ground fault.

[@d.kkumar4186]

Very nice video sir

[@bakilsorory3516]

@@industryautomation6661 I have same this number fault f7800 and led of drive not green not ready its always red flash

[@santanuadhikary123]

@@bakilsorory3516main MCB band Karke fir chalu Karo thik ho jayaga

[@kanathakur7910]

Apka namdar mil sakta he

[@karigar3705]

Clonfail
Err 37
Aa raha

[@shoaibhassan5454]

Ye procedure success nahi ho to

[@irfanahmeddae]

App ny try kiya

[@dineshkgm1156]

Very nice