Let's wait for all the comments saying, brake pads are cheap and should replace them! Just for context, I made this video during the COVID lockdowns, where it is so difficult to find parts. I just bought this bike and I just want to ride it. It's been more than a year, and I am still riding with the same set of brake pads. So hope this helps, because I looked at several videos and this is what worked. Thanks for watching.
@nonspecificnonsense6780 There are lots of different sizes. You should just take one of the pads off, then take it into the bike shop, and then they should be able to give you the new ones.
If you are going to heat the pads up like that make absolute sure that you get all of the break cleaner off first because break cleaners are no joke if you breathe any in
Be careful sanding like that, you'll get high and low spots. You should drag the sandpaper against the disc as the wheel is spinning. Gives a much more uniform surface. Bonus if you use a sanding block
1. Find a steep hill 2. Roll down applying brakes until they fade and a bit more The heat will burn off contaminants and your brakes will be good as new when they cooled down. Tip: Only do one brake at a time so you can stop using the other.
From my personal experience, that is a TERRIBLE idea, it has worked for me to do it over a prolonged period of time but it's almost impossible to do that in a singular run. If your brakes heat up enough to do that in a singular go you need larger rotors ASAP before brake fade straight up MURDERS you, because if you're unprepared it will. Please do not take brake health lightly.
@@johntheman2006it works if you just need to bed them in. The heat won’t remove contaminants so it’ll just glaze the pads. This process in video is great though except you need to bed them before shredding
You say it as if it was just pouring water on the pads and rotors then you're good to go when in reality if you do this with regular soap you'll become part of the asphalt or trail that you're riding in. It's important to use the apropriate products and ensure that everything is resurfaced and decontaminated (not "cleaned") properly. One thing that's bad about this short is that he doesn't say what grit he used, wich is important because if you go too coarse you'll damage your rotors, and if you go too fine you'll polish the surface and the pads won't bite properly anymore, meaning that there's not enough friction for them to heat up and deposit the coat on the rotors that actually grips the pads (wich is the reason why pads need to be beded in)
Just buy some isopropyl alcohol/ rubbing alcohol spray on a cloth/cotton wipe your disc done , sand the disc a little bit then clean the pads and don't freaking touch your brake disc our skin is oily and thus contaminate the disc
@@BrentsShop clean and sand them, after that you need to "bed in" the breaks by repeating several (20x) accelerations with moderate breaking to increase temperature and then making full hard stops (10x). Let t cool down and it will be good to go.
Remove the rotor. Clean with brake cleaner. Rub down if you really want to. Clean off the caliper with brake cleaner and wipe dry. Install new pads. Break in pads. Shred
Just a tip. Dont let your disc get so dirty in the first place. Use the brake cleaner after you washed the bike get a old sock clean it twise and take the grease off repeat 2nd step if needed. Done
Idk about using all those extra chemicals. Just spray and wipe the discs down with iso, sand the pads down with a fresh piece of 180, and for the love of god make sure you bed them properly.
On a vehicle to remedy dusty wheels from brakes is a brake pad problem, restoring all the same components and putting it back together and expecting different results is normally very disappointing obviously. This is why they have different grades of brake pads.
@@halfglassfullto be clear, it is NOT DW40, it was made by the same brand. Do NOT use WD40 on your brakes, it will be your first, and your last time doing it
I have done that and it's amazing to see people freak out from the bike lane when you're just chillin slow, brake a little and see them react like a truck is moving at 9000 MPH towards them. Even funnier when they're being jackasses walking on the bike lane and they don't hear you coming, 8/10 times they jump back to the sidewalk inmediately
if there is so much oil your pads are fucked. it will work for some time and come back, source : im a pro mech. change your pads, and if it starts again change the callipers. some leak.
u cant fix contaminated brake pads for ever. u can fix them for a while then u will wear them until the clean part is gone and sounds will come back again. buy new brake pads and be careful next time.
Nah, i bet it isn't as loud as the aliexpress pads i had on my Lapierre XD. The whole neighbourhood new i was round because it sounded like someone was blasting a trumpet with a stadium horn
Rubbing alcohol after each uses and you’re break pads will be good for a long time but when they wear out time change but I use rubbing alcohol clean calipers and clean the rest of bike and im good
My pads have been cleaned. The brake units have been bled and topped up with mineral oil. The rotors are new. I've less power than expected with squeal and vibration at low speed.
I tried this method 20yr ago and it only last a few min . If you are low on cash, try it but it was easier to just get new pad and clean the rotor really well.
Yeah, that was the plan until we can buy replacement pads (out of stock everywhere at that time). But forgot about it and still using the same set of pads 1 year later.
I once touched my front disc brake after braking down a very steep street to see how hot they get. Answer: Really, really, really hot. Don't ask me why.
I ride in San Francisco, and most of the time I ride down really steep streets and get up to 35mph sometimes. I knew the discs were hot one day and decided to quickly touch the ridge of the disk and it was definitely hot 😅
Someone had to address the . . . elephant . . . in the -room- brakes. Good job you did right there. My brakes levers are rather snapping my fingers of before locking the wheels. Now, let me see if I can do a job as good as you did.
I think you made it a bit more complicated than it has to be. Scrub the pads and rotors with dish soap mixed with water than rinse and wipe them off. Then get any remaining contaminants off with isopropyl alcohol.
I feel the soap also would absorb into the pads leaving less friction in the end. But i dont think he had to soak them either, but rather a wipe of the stuff to conserve
You should never use dish soap on the brake pads. Spirit is the best things to clean. You can soak in it. And change your pads to the resin one, never squiks to me.
@@vladivanov7645resin pads are silent yes, but the people that this video is directed at will most likely not ride anything that isn't sinthetic, resin or organic. There's a lot of low end brakes that don't have neither semi-metallic, metallic or ceramic pads available due to said brakes only being used with lower end rotors anyways, wich would get torn appsrt even by semi metallic ones.
This is such a solid guide... not only does this solve my issue, the breaks are even better than how they came stock to be honest. I'm probably going to use this video as a "modding" guide for bikes that I purchase in the future LOL tysmm
Nah bruh I wouldn’t even try, I’d go to my junk drawer and pull out a new rotor and set of pads Replace them and then get a squeaky clean rag and just sour there, cleaning the rotor Pads are done for brother 😭🙏🏽
Dont burn off the pads, ive destroyed e few of those and its not that cheap, maybe try just to just soak them and sand them .. those organic and semi metallic do not handle fire very well
How and what pads did you destroy by heating them up? Because you should probably NEVER use anything from that brand again or use something that isn't a welding torch, theese things NEED to hold up to heat, if they failed like that i'd be glad they didn't fail while i was on the bike, not even mad that i gotta go buy a different pair
Guys...today my brakes locked up and made me skid really dangerously and that shook me up real bad..any fixes? My pads are new Shimano Resin pads..same as the original. Thanks.
Interesting, with my road calipers all I do is hit it with a hose and a can of grease once a year or so to keep the bearing going. People do seem to love to buy stuff you need to mess with all the time though.
You mean rim brakes? Because we mostly stopped using thoose for multiple reasons, like a bent rim being catastrophic, the pads melting away under constant stress and hydraulic brakes being stronger in general.
@@Ferrari255GTO Only Freds stopped using those, lol. Sorry dude. If you have weak hands and can't use bike brakes there are several pushup variations that can fix that without spending any money.
@@Ferrari255GTO You have weak hands my guy sorry to break it to you. I barely have to squeeze to get a perfectly modulated non skip stop on my Dura Ace calipers and pads.
😂I really don't know what the previous owner of the bike was thinking (and my dad for buying the bike). The grease is really as thick as the drivetrain's
my brakes still dont work the brakes themselves have pressure and the pistons move and i cleaned the brake pads and rotor but they still dont work it just seems like the pads are not gripping on to the rotors
Is lines going around the disc fine? The disc on my cheap wheelset has them but going to use for a while to lose weight then go back to my lightest wheelset
Oh, I would check the brake pads to make sure it still have plenty of material. It shouldn't have any lines on it that you can feel with your finger nails.
I had to redo the brake cleaner soak like 3x before I completely get rid of the squeaking and got the full power back. If you can easily find a new set of pads, that's probably easier.
@@mysterious_man7673remove Tire, remove pads, buy New pads, give some Isopropanol on a towel and on the disk Brake and brakes so that everything come off. The put the New pads in the Brakes and install the tired again 👍
@@RidesWithJake Hello I used the rubbing alcohol in the rotor/disc breaks and it worked but it still remains the same so am I need to clean my brake pads?
Nah just keep it that way. It doubles as a horn. It's like saying "I dedicate this brake to you" to the idiot who caused it. You can add eye contact to increase the intensity of the message.
Let's wait for all the comments saying, brake pads are cheap and should replace them!
Just for context, I made this video during the COVID lockdowns, where it is so difficult to find parts. I just bought this bike and I just want to ride it.
It's been more than a year, and I am still riding with the same set of brake pads.
So hope this helps, because I looked at several videos and this is what worked.
Thanks for watching.
how do you know which ones to buy? Or are they a one size fits all
@nonspecificnonsense6780 There are lots of different sizes. You should just take one of the pads off, then take it into the bike shop, and then they should be able to give you the new ones.
It is not that cheap in where I live
Buy a new bike mate. (Joking)
I might try this, my back brake went put the other day, havent looked at it yet, but if I can fix it ill fix it😊
If you are going to heat the pads up like that make absolute sure that you get all of the break cleaner off first because break cleaners are no joke if you breathe any in
Thanks, for sure do not inhale any hazardous chemicals. 👍
Fire + brake cleaner = mustard gas
@@conor1423worse even tbh
Bro i smelled it every time in my garage because i like the smell
@@conor1423fire? I use it every time to start my car if it wont start
Be careful sanding like that, you'll get high and low spots. You should drag the sandpaper against the disc as the wheel is spinning. Gives a much more uniform surface. Bonus if you use a sanding block
1. Find a steep hill
2. Roll down applying brakes until they fade and a bit more
The heat will burn off contaminants and your brakes will be good as new when they cooled down.
Tip: Only do one brake at a time so you can stop using the other.
Don't do this all the time, because your rotor will get heat damage and even a brand new bad will have no stopping power
From my personal experience, that is a TERRIBLE idea, it has worked for me to do it over a prolonged period of time but it's almost impossible to do that in a singular run. If your brakes heat up enough to do that in a singular go you need larger rotors ASAP before brake fade straight up MURDERS you, because if you're unprepared it will. Please do not take brake health lightly.
Clean the disc and replace the pad. I’ve tried the going down hills applying the brake etc. Does. Not. Work.
@@johntheman2006it works if you just need to bed them in. The heat won’t remove contaminants so it’ll just glaze the pads. This process in video is great though except you need to bed them before shredding
It's crazy that cleaning works to fix something being dirty tbh
You say it as if it was just pouring water on the pads and rotors then you're good to go when in reality if you do this with regular soap you'll become part of the asphalt or trail that you're riding in. It's important to use the apropriate products and ensure that everything is resurfaced and decontaminated (not "cleaned") properly. One thing that's bad about this short is that he doesn't say what grit he used, wich is important because if you go too coarse you'll damage your rotors, and if you go too fine you'll polish the surface and the pads won't bite properly anymore, meaning that there's not enough friction for them to heat up and deposit the coat on the rotors that actually grips the pads (wich is the reason why pads need to be beded in)
Just buy some isopropyl alcohol/ rubbing alcohol spray on a cloth/cotton wipe your disc done , sand the disc a little bit then clean the pads and don't freaking touch your brake disc our skin is oily and thus contaminate the disc
Can u help I tried this mine still don’t work the disc is still 1.9 mm and the brake pads are still thick but don’t brake powerful enough
@@BrentsShop clean and sand them, after that you need to "bed in" the breaks by repeating several (20x) accelerations with moderate breaking to increase temperature and then making full hard stops (10x). Let t cool down and it will be good to go.
Remove the rotor. Clean with brake cleaner. Rub down if you really want to.
Clean off the caliper with brake cleaner and wipe dry.
Install new pads.
Break in pads.
Shred
I just got my mountain bike a few days ago and I'm already having this issue, thanks for helping
Keep in mind that after doing this you'll have to bed in your pads again, so make sure to go to a controlled space to do so
Use back laping compound . That compound is used for lawnmower blade .
if you don’t have brake cleaner use dawn dishwashing liquid for the pads.
Thanks
I usually rub dirt on it and it doesn't squeak. No joke.
Torches are good for this I doubt your cooktop gets hot enough to burn that oil off
My guy, fire is fire, doesn’t matter where it’s coming from, it’s the fuel that matters and they both use the same fuel
Your brakes were a symphony.. LOL 😂👍
Thanks, great tutorial
Glad it was helpful!
worked like magic.. thanks !!
Just a tip. Dont let your disc get so dirty in the first place. Use the brake cleaner after you washed the bike get a old sock clean it twise and take the grease off repeat 2nd step if needed. Done
@@roetietoe i bought the bike used (cheap) like that
@@RidesWithJake aha that make sense.. Old owner didnt wanna clean it and you bought it..
Idk about using all those extra chemicals. Just spray and wipe the discs down with iso, sand the pads down with a fresh piece of 180, and for the love of god make sure you bed them properly.
On a vehicle to remedy dusty wheels from brakes is a brake pad problem, restoring all the same components and putting it back together and expecting different results is normally very disappointing obviously. This is why they have different grades of brake pads.
🤔
or use WD40 to clean it, and that's last time you'll ever be cleaning the brake.
😂
very bad idea :D
he was using WD40?
He was using a degreaser made by WD40@@halfglassfull
@@halfglassfullto be clear, it is NOT DW40, it was made by the same brand. Do NOT use WD40 on your brakes, it will be your first, and your last time doing it
Thanks for the help bro, my breaks are squeaky af
No worries, hope you sort it out
I dont want it to fix cuz i use it like a horn haha
Проблема не только в звуке, они хуже тормозят колесо когда на тормозах масло
I have done that and it's amazing to see people freak out from the bike lane when you're just chillin slow, brake a little and see them react like a truck is moving at 9000 MPH towards them. Even funnier when they're being jackasses walking on the bike lane and they don't hear you coming, 8/10 times they jump back to the sidewalk inmediately
Oh thats why my brakes make a sound, didnt know before, thanks
if there is so much oil your pads are fucked. it will work for some time and come back, source : im a pro mech.
change your pads, and if it starts again change the callipers. some leak.
Thanks champ 👍
Very helpful my friend!
u cant fix contaminated brake pads for ever. u can fix them for a while then u will wear them until the clean part is gone and sounds will come back again. buy new brake pads and be careful next time.
I love trolling my friend with this noise its loud as hell but its gotta go
Nah, i bet it isn't as loud as the aliexpress pads i had on my Lapierre XD. The whole neighbourhood new i was round because it sounded like someone was blasting a trumpet with a stadium horn
Rubbing alcohol after each uses and you’re break pads will be good for a long time but when they wear out time change but I use rubbing alcohol clean calipers and clean the rest of bike and im good
My pads have been cleaned. The brake units have been bled and topped up with mineral oil. The rotors are new. I've less power than expected with squeal and vibration at low speed.
It need bedding in most probably. You have to let the brakes bed in on a hill.
@@RidesWithJake I've done 12 brakings per brake from 15-20mph to 3mph so far. The grip hasn't improved yet.
I tried this method 20yr ago and it only last a few min . If you are low on cash, try it but it was easier to just get new pad and clean the rotor really well.
Yeah, that was the plan until we can buy replacement pads (out of stock everywhere at that time). But forgot about it and still using the same set of pads 1 year later.
tysm it helped
I once touched my front disc brake after braking down a very steep street to see how hot they get.
Answer: Really, really, really hot.
Don't ask me why.
Lol
@@RidesWithJake Definitely not my brightest moment.
I ride in San Francisco, and most of the time I ride down really steep streets and get up to 35mph sometimes. I knew the discs were hot one day and decided to quickly touch the ridge of the disk and it was definitely hot 😅
Fuck around and find out moments lmao
I also did that, and my brakes are also contaminated, I don't know how to remove the pads though
Someone had to address the . . . elephant . . . in the -room- brakes.
Good job you did right there.
My brakes levers are rather snapping my fingers of before locking the wheels.
Now, let me see if I can do a job as good as you did.
Ah thanks
I think you made it a bit more complicated than it has to be. Scrub the pads and rotors with dish soap mixed with water than rinse and wipe them off. Then get any remaining contaminants off with isopropyl alcohol.
That doesn’t work I’ve tried it many times. The method in the video is the only one that’s ever worked for me
I feel the soap also would absorb into the pads leaving less friction in the end. But i dont think he had to soak them either, but rather a wipe of the stuff to conserve
You should never use dish soap on the brake pads. Spirit is the best things to clean. You can soak in it. And change your pads to the resin one, never squiks to me.
Contaminants like the dish soap you used? Bruh you must've crashed and hit your head on the previous incident with your brakes XD
@@vladivanov7645resin pads are silent yes, but the people that this video is directed at will most likely not ride anything that isn't sinthetic, resin or organic. There's a lot of low end brakes that don't have neither semi-metallic, metallic or ceramic pads available due to said brakes only being used with lower end rotors anyways, wich would get torn appsrt even by semi metallic ones.
Я люблю такие звуки от тормозов, когда есть возможность пытаюсь наигрывать на них какие нибудь простые мелодии.)
🤣
Just know you'll need to bed them in again after cleaning this thoroughly
Honestly I actually love the brake sound. And sometimes, the brakes will do the job of the Bell.
So, I just like to skip it.
😂
wash the disc and brake pads first with alcohol and then with toothpaste(colgate) and air-dry it, works perfectly por me.
Sandpaper and blowtorch to the pads
Only my front disc keeps squeeking pls someone tell what to do
Try the steps here, it could help 👍
Just use dish soap and a stiff brush, then do some big stops and itll cook it off
I just use a torch and that’s good enough.
This is such a solid guide... not only does this solve my issue, the breaks are even better than how they came stock to be honest.
I'm probably going to use this video as a "modding" guide for bikes that I purchase in the future LOL
tysmm
As a mechanic that is actually supposed to charge money for the time this would never be worth it and could not be counted on vs cost of new pads.
Yeah absolutely
using sandpaper, wash it with gasoline both pad and disc.
gasoline is the best oil/grease remover on disc brake 😂
Or use kerosene and diesel for making them for trash
Rule nr 1, never touch disc
👍👌
rim breaks for the win
👍
Nah, Hydraulic gang rise up!
Lol
Rim brakes and tubes, not tubeless. Like Back to the Future .
Nah bruh I wouldn’t even try, I’d go to my junk drawer and pull out a new rotor and set of pads
Replace them and then get a squeaky clean rag and just sour there, cleaning the rotor
Pads are done for brother 😭🙏🏽
Yeah nowadays i’ll get a new one
Dont burn off the pads, ive destroyed e few of those and its not that cheap, maybe try just to just soak them and sand them
.. those organic and semi metallic do not handle fire very well
How and what pads did you destroy by heating them up? Because you should probably NEVER use anything from that brand again or use something that isn't a welding torch, theese things NEED to hold up to heat, if they failed like that i'd be glad they didn't fail while i was on the bike, not even mad that i gotta go buy a different pair
Put wd40 on the pads and the disc makes them a charm
+200 to speed
Haha, hopefully 8 year old Timmy that just got his first mountain bike doesn't see this
What can we use instead of brake decreaser and isopropyl alcohol 😅😅
I don't have it in my home !!
Can we use acetone??
Yeah maybe,
Simple green.
Never burn ur disc breaks after using brake cleaner it is dangerous to breathe in and can kill u ! Also I soak my pads overnight it’s better
Ah yes, thanks, I left the brake cleaner an hour, before burning the oil off
It's really work😮😮😮😮
Tbh, everything is good but you should just buy new pads if you get to the point you have to burn stuff.
True that
True that
Guys...today my brakes locked up and made me skid really dangerously and that shook me up real bad..any fixes? My pads are new Shimano Resin pads..same as the original. Thanks.
It might need some bedding in if they’re new
W-40 YOU ARE WELCOME
😂
😂😂😂
Good tips
Thanks Krishna
Interesting, with my road calipers all I do is hit it with a hose and a can of grease once a year or so to keep the bearing going. People do seem to love to buy stuff you need to mess with all the time though.
You mean rim brakes? Because we mostly stopped using thoose for multiple reasons, like a bent rim being catastrophic, the pads melting away under constant stress and hydraulic brakes being stronger in general.
@@Ferrari255GTO Only Freds stopped using those, lol. Sorry dude. If you have weak hands and can't use bike brakes there are several pushup variations that can fix that without spending any money.
@@___Bebo___ no, i have a 200mm fork that provides more grip than thoose brakes can handle
@@Ferrari255GTO You have weak hands my guy sorry to break it to you. I barely have to squeeze to get a perfectly modulated non skip stop on my Dura Ace calipers and pads.
@@___Bebo___ broken cables would like to disagree with you
1 spray rotor with brake cleaner 2 install new pads.
I use honer for i use on cars or sand paper and wire brush on pads with brake been doing for years and work great
Do you use regular car brake cleaner? Or is there a special formula for bikes
I did use a regular car brake cleaner, it's much stronger which is needed for this heavily contaminated brakes.
I just ride it through the river that seems to do the trick 😂
😂
do you need to take off your wheel to take out the brake pads? one more question. how can you tell what pads go to a certain disc
Yeah, you need to. And you have to search the pads based on which brakes you have.
Well, alternatively you can dismount the caliper from the fork
I thought wd40 on bike brakes was a big No No? That wd40 attracts dirt and grime and make all your braking components all gross?
That's a WD40 DEgreaser 😅
Man. Disk breaks are a lot of work!
They’re
@@RidesWithJake Mines aren’t even greasy nor dirt. Bike is fairly new. Maybe 2-3 months old and the front break hardly does anything. So dangerous.
nice polygon! is it a d6?
Thanks! Its a bigger brother, the old N7
oohhh cool!@@RidesWithJake
Nah man, just WD-40💀
hahaha
WD40 shouldnt even be in the same room as your disc rotors!!!
😂I really don't know what the previous owner of the bike was thinking (and my dad for buying the bike). The grease is really as thick as the drivetrain's
Noisy brakes let hikers know what’s coming their way
Well this wasn't my problem.. but mine was that my calipers had no more like grip due to me having using it for 3 years without changing it
Calipers? Probably need new pads and/or rotors 😀
Bed your breaks (before shredding)
Nice stem
Gotta love the shorties
Dont touch them with your fingers for one.
Lol on a clean rotor yes
Tried this, twice. Ended up replacing pads *and* rotors... Same problem after a couple of weeks. I just don't understand.
Interesting, somethings keep contaminating your brakes?
Throw Shimano brakes in the garbage right next to Sram and you won't have problems
😅
Thats why i choose rim brakes all day
Good on you 👍
@@RidesWithJake btw i gotta tell ya i got no hate on disc brakes and drum brakes and deffenetly no hate on u cuz i actualy love ur videos🔥💯
This sound like skeleton hang in fan meme
😂
What grit sand paper do you use for the pads?
It was an 800grit sand paper if I remember correctly, I only lightly scuffed it, and removed some surface rust at the same time.
Or you can just buy new brake pads they are like $10
try $40 for many road bikes with Shimano or SRAM.
my brakes still dont work the brakes themselves have pressure and the pistons move and i cleaned the brake pads and rotor but they still dont work it just seems like the pads are not gripping on to the rotors
Yeah mine was the same before, it took a couple of tries like 5x. I think its time for new pads, and thoroughly clean the rotors
Wont heating the pads that much glaze them?
It was fine for me, some people use a blowtorch, and I sand it afterwards
All u need to do is add some grease to the brake disks
😂
Is lines going around the disc fine? The disc on my cheap wheelset has them but going to use for a while to lose weight then go back to my lightest wheelset
Oh, I would check the brake pads to make sure it still have plenty of material. It shouldn't have any lines on it that you can feel with your finger nails.
@@RidesWithJake just checked you can see the lines but some how not have nail catch on any of it (not feel with nail?)
Honey, my toothbrush tastes weird…
😂
Lord... take the rotor off and sand and inspect it. Who you teachin?
Yeah thanks, I don't have a bottom bracket tool then.
No do not use car brake cleaner
Real men dont use breaks 🗿
😅
@@RidesWithJakefr I don't use your foot like a man 🗿
Real men know how to spell. "breaks"?
mine still squeak as heck any suggestions please
I had to redo the brake cleaner soak like 3x before I completely get rid of the squeaking and got the full power back. If you can easily find a new set of pads, that's probably easier.
How did you get them so dirty?? Did you just spray chain oil on them 😂😂
Hahaha Dad bought it from a kid, and we’re wondering about that too, seems like it was literally sprayed with lube
I did this 😂 and idk how to fix it
@@mysterious_man7673remove Tire, remove pads, buy New pads, give some Isopropanol on a towel and on the disk Brake and brakes so that everything come off. The put the New pads in the Brakes and install the tired again 👍
What grit sandpaper did you use?
Can't remember I believe it was 400grit if you have something rougher, just sand lightly, you just have to scuff it up.
@@RidesWithJake alright thank you
Is it good to use rubbing alcohol?
👍
@@RidesWithJake Hello I used the rubbing alcohol in the rotor/disc breaks and it worked but it still remains the same so am I need to clean my brake pads?
WD -40 😂😂😂
I don’t have brake cleaner
You can use alcohol to dissolve the oil
I have done this but still it sounds
Sorry to hear that, it might be time for new pads.
Nah just keep it that way. It doubles as a horn. It's like saying "I dedicate this brake to you" to the idiot who caused it. You can add eye contact to increase the intensity of the message.
Hahaha,
This is the way
This is the way
I replaced my brakes and they still squeak
Oh no, that’s not good
littereraly same. maybe i should replace the rotors idk
Use alcohol
brake cleaner is toxic when burned lol
😅
That doesn't change.
Sorry to hear that, sometimes you have to do it multiple times or time for new pads.