Bi-Xenon Projector Retrofit - Ford Mondeo Mk3

แชร์
ฝัง
  • เผยแพร่เมื่อ 27 ม.ค. 2025

ความคิดเห็น • 65

  • @pibblesnbits
    @pibblesnbits 8 ปีที่แล้ว +7

    very well done!!! The only thing that i would of done differently is paint the reflector bowls black to reduce glare.

    • @Tyykiluoto
      @Tyykiluoto  8 ปีที่แล้ว +1

      Thanks! The owner of the car wanted "original look", so no painting this time ;)

    • @pibblesnbits
      @pibblesnbits 8 ปีที่แล้ว

      That's how I like it too! Good taste!

  • @StalloneSRB
    @StalloneSRB 8 ปีที่แล้ว +2

    I have to do this when I buy Mondeo. :)

  • @simonjohnhinton1938
    @simonjohnhinton1938 7 ปีที่แล้ว +1

    Fortunately I bought a ghia x that already had xenons lol. Looks a right pain in the arse to remove the cover. They are better lights than standard and to be honest if I bought another car they'd have to have them that's for sure.

    • @Tyykiluoto
      @Tyykiluoto  7 ปีที่แล้ว +1

      Yeah, removing the cover was a pain on these lights. The glue was hard and didn´t soften with heat as with most of the original lights.

  • @MrLorenczo
    @MrLorenczo 6 ปีที่แล้ว

    Great job

  • @Marina38sanchez
    @Marina38sanchez 6 ปีที่แล้ว

    How much to craft a pair of these and send them to Brazil? Hahaha.
    Very nice job, man. Btw, loved the music too!

  • @setnakhaewese
    @setnakhaewese 7 ปีที่แล้ว

    nice work

  • @zlatanhairlic8919
    @zlatanhairlic8919 8 ปีที่แล้ว +2

    Nice, but your hotspot on the right projector is not centered ;) your bulbs dont fit right, you need to drill a bit on the bulb socket, so they go a bit more into the projector ;)

    • @Tyykiluoto
      @Tyykiluoto  8 ปีที่แล้ว

      +zlatan Hairlić The light reflects a little funny from the highly reflective and textured surface of the door, and it does look different in real life. But after looking at the footage again, you might have a point. I have to check that out. Thanks for the tip! :)

  • @АлександрЯрославцев-ы5г
    @АлександрЯрославцев-ы5г 7 ปีที่แล้ว

    And not easier to mount a head lamp to warm up the headlight, it is much easier to stick around

    • @Tyykiluoto
      @Tyykiluoto  7 ปีที่แล้ว

      These cheap aftermarket headlights were glued with some kind of permanent glue. Heating didn't help at all.

  • @KingABS
    @KingABS 9 ปีที่แล้ว

    Good job . Any moisture issues when driving in snow or rain storm ?

    • @Tyykiluoto
      @Tyykiluoto  9 ปีที่แล้ว

      +King ABS Thanks! Actually, these cheap aftermarket lights used to get foggy inside because the lenses weren't glued in properly. After the modification there has been no issues with moisture :)

    • @KingABS
      @KingABS 9 ปีที่แล้ว +1

      niice

  • @luisr5113
    @luisr5113 8 ปีที่แล้ว +1

    But I have some doubts. Did you can help me please ...
    What kind of hid bulbs you use? and
    What kind of glue / silicone used to close the optical?

    • @Tyykiluoto
      @Tyykiluoto  8 ปีที่แล้ว +2

      These projectors use H1 bulb, so the bulb is from aftermarket H1 xenon kit. The glue is a butyl glue. That kind of glue doesn't harden fully and can be softened even more with heat, so you can remove the lens easier if you have to.

  • @vildisvildis
    @vildisvildis 7 ปีที่แล้ว

    Looks like possible do 2x2low beams and 2x2 high beams?
    2 bi-xenon projectors per headlamp and wuolia 4low beams + fog lights bi-xenon + 6high beams. hell a lot of light :)

    • @Tyykiluoto
      @Tyykiluoto  7 ปีที่แล้ว

      Yes, definitely possible and would surely be cool :)

  • @fththkll4979
    @fththkll4979 6 ปีที่แล้ว

    Very helpful video to understand the project. Thanks a lot!
    My quesiton is what about the performance of the projectors after 2,5 years. Are they still doing their job well or started to get dark on lens and reflectors? I thought to use these projectors but after reading many reviews of them decided to use OEM projectors like Hella E55. In my opinion Hella could be better but very very difficult to install on the headlights. These ones are much more easier with their screw-installing type. Maybe i m going to use a couple of them in my next project. But if you say; -Yes, they are still working enough! :) Thanks again.

  • @feedbrain6257
    @feedbrain6257 6 ปีที่แล้ว

    Hello,
    thx please can i have a model of Butyl sealant that you used. I couldn't see it very well, u was moving very fast when adding the glue

    • @Tyykiluoto
      @Tyykiluoto  6 ปีที่แล้ว

      It was Bostik Butyl Mastic 1590, if I remember correct. Any automotive butyl sealant will work.

  • @feedbrain6257
    @feedbrain6257 6 ปีที่แล้ว

    Hi, you didn't add any fuse for this xenon lamp to work? THX

    • @Tyykiluoto
      @Tyykiluoto  6 ปีที่แล้ว

      No fuses added, but there is fuses for the original halogen lamps and the xenon lamps are powered trough those

    • @feedbrain6257
      @feedbrain6257 6 ปีที่แล้ว

      thx

  • @PaskaTF2
    @PaskaTF2 8 ปีที่แล้ว

    Mistä hommasit nuo tarvikeumpiot ja mitä merkkiä ne on? Niihin ilmeisesti sopii ne alkuperäiset korkeudensäätömoottorit? Onko mitään xenon hyväksyntämerkkejä präntätty umpion "lasiin" / kuoreen?

    • @Tyykiluoto
      @Tyykiluoto  8 ปีที่แล้ว

      spareto.com. Nämä umpiot ovat merkiltään TYC, eli halvat ja huonot :). Valokuvio näissä umpioissa oli ennen modausta ihmeellinen (kirkkaita pisteitä ja pimeitä kohtia kuviossa) ja valoteho paljon heikompi kuin alkuperäisissä, lisäksi toisen umpion korkeussäädön säätövara loppui kesken, suosittelen siis kokeilemaan jotain muuta merkkiä :). Alkuperäiset korkeudensäätömoottorit sopivat suoraan kiinni. Hyväksyntämerkinnät ovat umpion mustassa runko-osassa, "lasissa" ei ole mitään merkintöjä. Hyväksynnät löytyy vain halogeeni-polttimoille.

  • @2WheelDerness
    @2WheelDerness 8 ปีที่แล้ว

    i have a question..I want to put on my bike 2 Bi-xenon projectors... my bike have 1 headlight H7 for low beam and one H7 for hi beam. if i put those projectors that use H1, how do i power the both projectors? where it suppose to connect the harness that came with the projectors? it`s ok if i power both H1 bulbs with low beam harness and the projector (actuator/solenoid ) with hi beam harness? (I also want to put H1 LED instead of HID. it will work??

    • @Tyykiluoto
      @Tyykiluoto  8 ปีที่แล้ว +1

      Correct, wire both of the H1 bulbs to low beam, and the projector actuators to the high beam. Only thing you have to check/test is that can the original wiring and fuse of the low beam take the increased current of the two lights. If it doesn't you will just have to do little more wiring and ad a relay to power the lights.
      Leds will work. However, all the cheap led kits (H4, H7, H1, etc.) are useless in light power and beam shape, so be careful when choosing witch one to get.

  • @jcalmar74
    @jcalmar74 5 ปีที่แล้ว

    Do u have the ebay link please!
    Can be installed on any car or suv?
    Thank 4 u video!

  • @Spoolie
    @Spoolie 6 ปีที่แล้ว

    What sealant did you use to seal these? Also i've just done a retrofit with ebay parts, but find they have virtually no distance, very bright to look at and in the foreground but can't see far

    • @Tyykiluoto
      @Tyykiluoto  6 ปีที่แล้ว +1

      Some butyl-based glue if I remember correct. I had the same problem with the beam distance and had to modify the projector and the light housing to get the beam pointing high enough.

    • @Spoolie
      @Spoolie 6 ปีที่แล้ว

      Mine seems to be fine height wise, i aligned it against a wall, it just seems that the light itself drops off after a certain distance and provides basically no illumination :(

  • @marcinp9589
    @marcinp9589 6 ปีที่แล้ว

    Hi. How did you plug h1 bulbs? I have halogen h7 in my mondy

  • @tonypotter5589
    @tonypotter5589 6 ปีที่แล้ว

    Can you provide a link for the projector please

    • @Tyykiluoto
      @Tyykiluoto  6 ปีที่แล้ว

      Do a search on ebay for "bi-xenon projector"

  • @t5jerry
    @t5jerry 8 ปีที่แล้ว +7

    good video, SHAME about the music !!!!

    • @Tyykiluoto
      @Tyykiluoto  8 ปีที่แล้ว +1

      Thanks for commenting

  • @RobH.
    @RobH. 4 ปีที่แล้ว

    MOT failure if Xenon fitted without headlamp washers!

    • @curtisj2165
      @curtisj2165 4 ปีที่แล้ว

      True, and you also need self levelling suspension to pass am MOT

  • @laurentiugherman508
    @laurentiugherman508 8 ปีที่แล้ว

    lens is 3 inch or 2.5 inch?

  • @lorencezjosealfredo1611
    @lorencezjosealfredo1611 7 ปีที่แล้ว

    A question ...... they can sell me 1 pair .... I have a 2006 mondeo

    • @Tyykiluoto
      @Tyykiluoto  7 ปีที่แล้ว

      What is your question? :)

    • @lorencezjosealfredo1611
      @lorencezjosealfredo1611 7 ปีที่แล้ว

      Tyykiluoto Engineering Do you have shipments to Mexico ??

    • @Tyykiluoto
      @Tyykiluoto  7 ปีที่แล้ว

      No, I don´t sell these, sorry. You can order the parts from ebay and do it yourself.

  • @richardholler8595
    @richardholler8595 6 ปีที่แล้ว

    cena??

  • @Nicusor95
    @Nicusor95 8 ปีที่แล้ว

    35w or 55w ???

    • @Tyykiluoto
      @Tyykiluoto  8 ปีที่แล้ว +1

      This has 35w, but you could use 55w as well

  • @duned3736
    @duned3736 7 ปีที่แล้ว

    great project! must have...F*ck i live in Germoney

  • @gadori
    @gadori 7 ปีที่แล้ว

    Well done, thx, I gonna follow you. But the music.........

  • @radekmamcarz
    @radekmamcarz 5 ปีที่แล้ว

    Muzyka rozdupca

  • @BoroDa8735
    @BoroDa8735 2 ปีที่แล้ว

    Better to buy one original

  • @michaniemiec7084
    @michaniemiec7084 6 ปีที่แล้ว

    Big shit 😔😭🤕

  • @anonymousjohnsmith2798
    @anonymousjohnsmith2798 6 ปีที่แล้ว

    This is great Job but this is still illegal...

    • @Tyykiluoto
      @Tyykiluoto  6 ปีที่แล้ว

      Yes, we know... :)

  • @mickborthwick3814
    @mickborthwick3814 3 ปีที่แล้ว

    Still shite HIDs