I had the same issue with the shoulder straps. There is another clamp at the top of the sprayer to allow you to remove the slack from the strap so the shoulder pads will sit on your shoulders.
Great review. I just upgraded from the 2 gallon version since the pump failed. When I get to the 1/2 gal point, I'll just either refill the tank or decant it into an empty jug for next time. To me it seems like more of a nuisance than a big con. Thanks
The issue when there is a half gallon left- don't use the sprayer with the inlet filter, and note which side of the sprayer the inlet is on. When you the tank is down to 1/2 gallon or so, you need to use your free hand to tilt the sprayer tank so all the fluid is flowing into the inlet. If you do that you'll have good pressure all the way to the end. The asymmetric inlet location is another bad design decision that was allowed for some reason. The filter just makes it worse. Also, take the time and use a measure cup to measure out your own 1 gallon marks. The Ryobi marks are totally off and also will make it hard to get correct mixing ratios.
I had the same issue now and again. I also toot the extra time to measure and mark sharpie lines on the tank to show me actual measurements. I stick my hand in the tank and rub the inlet filter to clean it off.
Great video Thankyou. I have everything I want in the Ryobi range & was thinking about getting this . But the fact that it has uncomfortable straps ,no padding behind your back & also the fact that it does not completely empty means I won’t buy it until they fix this atleast. I have multiple silvan sprayers & I think for now I’ll just stick with them. I hope Ryobi watches this & listens!!
Well I know more than I did about this sprayer I've only used the handhelds, I'm a big guy so I can see where one of the cons would bother me and I'm little concerned about price. I don't spray a lot but the thought was good. ✔💪
Works without the chest strap just figured if you pay for that should work too. Lol. I agree price is a concern especially if you’re on the field spraying any lost of product is a profit lost. 😞
I had the same issue. the strainer at the bottom of the tank is too tall and when the liquid starts getting below the top of the strainer it starts sucking air. the strainer is easy to remove jus t pull it out and you can work with it out of the tank. what I did is I used some duct tape to seal off the top half of the strainer and left the lower half open to let the liquid in. I have used mine twice now after i did this and it uses most of the liquid in the tank. alot better than before. I think the strainer should be redesigned at a lower profile.
I have the previous model with the frame looks great used once only to this day does not work! Turns on makes noise nothing comes out at all!! I set it aside to look at never did also when I bought it I did not open for long time any one out there know what it can be?
I’m surprised all the reviews I’ve seen and nobody talks about how slow you need to walk to properly distribute the correct amount of liquid per square foot. I feel you about the pressure changes and the inlet placement within the tank giving you unusable liquid at the end. Gotta do the “body tilt” technique to get the last out lol.
I agree. That tilt game is serious to get at least half of what was left out. I got rid of it can’t deal with it anymore. No way possible people have this good reviews with the issues it has. Whoever did must have received a payday.
I just got mine. When I turn the dial to lower PSI, it makes that Eeeeeeee sound non stop. Once I turn the PSI all the way up or to a certain point at a higher PSI, the Eeeeeee sound stops. Does yours do that or did I get me a lemon?
This is an out of the box experience review. If you need to make modifications to a spray tank to work for a regular homeowner who does not want to do this it is not worth it. Modifications can be made at at what cost/time versus buying a sprayer $40 more that works better.. just keep that in mind, i could have made a mod to this and made a mod video how to fix this the average person will not they want to load and go.
@@DanTheLawnMan it will take 2 minutes to do and cost you around 2 dollars if anything depending on what you have lying around in the garage. My 10 year old could do it so anybody could, it's just having the brain to see the issue and how to resolve it. Many people have bought these sprayers only to find out there is a problem when it's too late to return it, so finding a solution for those guys is a plus.
I said Anything else in a price range of $40-$60 more than the ryobi. I’ll keep the view you can your thumbs down. Next time just ask in the comment if you want me to link the backpack I use. Which I have in most of my other videos. 👎🏽
Awesome honest review!
Have to let the people know, and if ryobi ever watches this maybe they make adjustments in the future? 🤷🏽♂️
That is for sure 👍
Great review Dan appreciate the yays and nays . Thanks again.
Always feel the 🫶🏽 when you’re watching. I have something special for you soon my friend.
@@DanTheLawnMan always a pleasure Dan
Great, honest review Dan. Well done video!
That’s for dropping in and checking the video out 👊🏽
@TheLawnLover definitely great.
I had the same issue with the shoulder straps. There is another clamp at the top of the sprayer to allow you to remove the slack from the strap so the shoulder pads will sit on your shoulders.
Great Review Dan ❤
Appreciate you checking it out 🫶🏽 thanks bro
Great review. I just upgraded from the 2 gallon version since the pump failed. When I get to the 1/2 gal point, I'll just either refill the tank or decant it into an empty jug for next time. To me it seems like more of a nuisance than a big con. Thanks
The issue when there is a half gallon left- don't use the sprayer with the inlet filter, and note which side of the sprayer the inlet is on. When you the tank is down to 1/2 gallon or so, you need to use your free hand to tilt the sprayer tank so all the fluid is flowing into the inlet. If you do that you'll have good pressure all the way to the end.
The asymmetric inlet location is another bad design decision that was allowed for some reason. The filter just makes it worse.
Also, take the time and use a measure cup to measure out your own 1 gallon marks. The Ryobi marks are totally off and also will make it hard to get correct mixing ratios.
I can agree with this
I had the same issue now and again. I also toot the extra time to measure and mark sharpie lines on the tank to show me actual measurements.
I stick my hand in the tank and rub the inlet filter to clean it off.
Great video Thankyou. I have everything I want in the Ryobi range & was thinking about getting this . But the fact that it has uncomfortable straps ,no padding behind your back & also the fact that it does not completely empty means I won’t buy it until they fix this atleast. I have multiple silvan sprayers & I think for now I’ll just stick with them.
I hope Ryobi watches this & listens!!
Just save a few more bucks and get a better sprayer this one two thumbs down. 👎🏽 👎🏽
Thank you DanTheLawnMan!! great vid. I put a foam pad for my lower back, by the way.
That’s a great idea. The plastic definitely is a back killer I would put a shirt for extra cushion.
Well I know more than I did about this sprayer I've only used the handhelds, I'm a big guy so I can see where one of the cons would bother me and I'm little concerned about price. I don't spray a lot but the thought was good. ✔💪
Works without the chest strap just figured if you pay for that should work too. Lol. I agree price is a concern especially if you’re on the field spraying any lost of product is a profit lost. 😞
Appreciate the review. 👍🏽
My pleasure 😉
I had the same issue. the strainer at the bottom of the tank is too tall and when the liquid starts getting below the top of the strainer it starts sucking air. the strainer is easy to remove jus t pull it out and you can work with it out of the tank. what I did is I used some duct tape to seal off the top half of the strainer and left the lower half open to let the liquid in. I have used mine twice now after i did this and it uses most of the liquid in the tank. alot better than before. I think the strainer should be redesigned at a lower profile.
Good review honest!
Always 💯 on this channel
Thank You for sharing. Definitely saved me some funds
Happy to help not worth the hype other day it is on TH-cam. Two thumbs down 👎🏽 and I like ryobi tools but this just doesn’t cut it.
I have the previous model with the frame looks great used once only to this day does not work! Turns on makes noise nothing comes out at all!! I set it aside to look at never did also when I bought it I did not open for long time any one out there know what it can be?
good review thanks for posting !
You’re welcome thanks appreciate it!
I’m surprised all the reviews I’ve seen and nobody talks about how slow you need to walk to properly distribute the correct amount of liquid per square foot. I feel you about the pressure changes and the inlet placement within the tank giving you unusable liquid at the end. Gotta do the “body tilt” technique to get the last out lol.
I agree. That tilt game is serious to get at least half of what was left out. I got rid of it can’t deal with it anymore. No way possible people have this good reviews with the issues it has. Whoever did must have received a payday.
@@DanTheLawnMan what did you end up getting after?
@@hawaiiantimes7702 amzn.to/483TkIu
This ideal for pest control?
If you are willing to deal with the issues. Yes. The fan tip it comes with is good for it. I did a pest video with this same backpack sprayer.
I just got mine. When I turn the dial to lower PSI, it makes that Eeeeeeee sound non stop. Once I turn the PSI all the way up or to a certain point at a higher PSI, the Eeeeeee sound stops. Does yours do that or did I get me a lemon?
Sounds like a 🍋
Do you own a Ryobi Sprayer such as the one in this video? if so share your thoughts below ⬇
Ive come up with a solution to the problem of getting all of the liquid out of the tank, I'll upload a VT when I get a chance.
This is an out of the box experience review. If you need to make modifications to a spray tank to work for a regular homeowner who does not want to do this it is not worth it. Modifications can be made at at what cost/time versus buying a sprayer $40 more that works better.. just keep that in mind, i could have made a mod to this and made a mod video how to fix this the average person will not they want to load and go.
@@DanTheLawnMan it will take 2 minutes to do and cost you around 2 dollars if anything depending on what you have lying around in the garage.
My 10 year old could do it so anybody could, it's just having the brain to see the issue and how to resolve it.
Many people have bought these sprayers only to find out there is a problem when it's too late to return it, so finding a solution for those guys is a plus.
@@dannym670 sounds good 👍🏽 don’t take it the wrong way or read it the wrong way it’s all good. Post it here if u want 👍🏽.
@@dannym670 what's the fix?
@@thaddeusmontgomery7484 I've just uploaded a quick video showing the problem I had and how I solved it 👍
Ryobi 18v sprayer losing pressure fixed 🤞
What is your favorite sprayer?
Have not found one yet although I have been using one for sometime now that has not failed me and given me any problems yet and I really like.
18V Ryobi for sure 👍
@@DanTheLawnMantry the Flozone cyclone 3
@@DanTheLawnMan thanks for your honest review, so which one do you currently use?
I have a 2 hectares of farmland and need a good sprayer
Holy sh&t I thought that wand was gonna snap in two😮
Lol
I think You put the straps on upside down. The padded area goes on top.
I don't belive so because the straps to tighten and loosen are at the top for pull down access
@@DanTheLawnMan I wish I could show you a pic of mine.
Can you pray stain with it? I am looking to stain my deck.
With paint alone no way to thick of a application
I had one and hated it. Low quality, 1/2 gallon leftover, and leaky nozzle is a deal breaker. I returned mine to Home Depot.
I agree with you it’s that bad.
You should had name whats the better backpack for that you get Thumbs down 👎smh
I said Anything else in a price range of $40-$60 more than the ryobi. I’ll keep the view you can your thumbs down. Next time just ask in the comment if you want me to link the backpack I use. Which I have in most of my other videos. 👎🏽
@@DanTheLawnMan |Come on what is it then ?
Great review Dan " you are the man ". I don't have a big back but my cape definitely does get in the way lol. 👍💚🦸
🤣 Morning and afternoon known as Striperman, Night a cape crusader