Thank you so much for making this video !!! Been trying to reverse thrust my new RC Jet since last night reading the paperwork. I did it immediately after watching your video. Thanks again
You have created an excellent video on how to Program and ESC via the Transmitter. This can be a confusing task to someone that has not performed this procedure before. I think you have removed a lot of the confusion regarding this process. Well done! See you in the Air!
Thank you, I had been looking for these instructions for 2 days, this manual is 100 % compatible with Volantex ESC for Model ASW 28 RC Plane. I have now successfully programmed !! Thanks a lot !!
GGGRreat !!! Thanks for the concise and clear presentation!!! Explaining the “Morse-code” really, really took the arbitrary mystery out of the action. I will have to go over this several times but see it can be understood not some rote rot to memorization...beep,beep,dot, daa! dumb,dot,dot,dot.......
I got here searching for a way to activate motor breaks for my new Bixler 3. The B3 comes with HK 20A ESC (no "UBEC" on the label) but the ABCD sounds and melodies are entirely different. However I figured out that only the sounds are different, but the order of functions behind the melodies is the same. So e.g. just wait for the second melody to activate/deactivate the break; wait for the 8th melody to trigger a factory reset. At least for these two functions it turned out fine for me.
Hello, When I try to put my ESC (REDBRICK 100A with BEC) into programming mode the ESC doesn't respond. I put throttle to max position, then turn the model on (it has a flight controller matek-H743 v3 with ardupilot. The BEC red wire is cut off, and only signal and ground is plugged into the FC, that is because the servos already have power through the FC and so does manufacturer disclose that I shouldn't put BEC wire to the throttle servo pins), the ESC then beeps once (in this video I haven't found a single sound that would be remotely close to the one I'm hearing, except for the last two short beeps) then it beeps with the same sound 8 times in a row, then pause, and then 2 short beeps. I'm also using li-po 4S battery. I tried putting throttle into different positions, but still no other response than the one I described. Even if I plug in the battery when the throttle is in the lowest position, the beeping is in the same order as in the max position. Could you help?
What I don't see here in TX accessible menu is motor timing that it is accessible from programing card, but I'm not sure if it is needed for max efficiency airplane..?
I had the same effect when I powered up the model for the first time. Then I performed the first step of the programming procedure (= throttle) and now it works. Did you try this?
Thank you so much for making this video !!! Been trying to reverse thrust my new RC Jet since last night reading the paperwork. I did it immediately after watching your video. Thanks again
Thanks alot guy, lol I been at this all morning. I even have hk program card and I can't figure that dam card out, but ur video done the trick!!! 😂
You have created an excellent video on how to Program and ESC via the Transmitter. This can be a confusing task to someone that has not performed this procedure before. I think you have removed a lot of the confusion regarding this process. Well done! See you in the Air!
... even for someone who has performed it before. You are not alone.
Thanks a lot for taking the time to make this video.
Thank you, I had been looking for these instructions for 2 days, this manual is 100 % compatible with Volantex ESC for Model ASW 28 RC Plane.
I have now successfully programmed !! Thanks a lot !!
Like all the rest, thanks for posting finally understand how to program my old 60 amp esc . Great clear instructions that l can comprehend. 👍
Glad it helped
Thank You for making this video! Seriously, Thank you. I couldn't figure this out without your help!
GGGRreat !!! Thanks for the concise and clear presentation!!! Explaining the “Morse-code” really, really took the arbitrary mystery out of the action.
I will have to go over this several times but see it can be understood not some rote rot to memorization...beep,beep,dot, daa! dumb,dot,dot,dot.......
I have to review this video every time I chane settings on the ESC. Thank your for your kind remarks.
I got here searching for a way to activate motor breaks for my new Bixler 3. The B3 comes with HK 20A ESC (no "UBEC" on the label) but the ABCD sounds and melodies are entirely different. However I figured out that only the sounds are different, but the order of functions behind the melodies is the same. So e.g. just wait for the second melody to activate/deactivate the break; wait for the 8th melody to trigger a factory reset. At least for these two functions it turned out fine for me.
Great video. Thank you..
Hello,
When I try to put my ESC (REDBRICK 100A with BEC) into programming mode the ESC doesn't respond. I put throttle to max position, then turn the model on (it has a flight controller matek-H743 v3 with ardupilot. The BEC red wire is cut off, and only signal and ground is plugged into the FC, that is because the servos already have power through the FC and so does manufacturer disclose that I shouldn't put BEC wire to the throttle servo pins), the ESC then beeps once (in this video I haven't found a single sound that would be remotely close to the one I'm hearing, except for the last two short beeps) then it beeps with the same sound 8 times in a row, then pause, and then 2 short beeps. I'm also using li-po 4S battery. I tried putting throttle into different positions, but still no other response than the one I described. Even if I plug in the battery when the throttle is in the lowest position, the beeping is in the same order as in the max position. Could you help?
Please see if this helps : atorie-m-m.main.jp/redbrick50~200A%20manual.pdf
Ty so much ✌🏼
Thanks for the video! Can you post a file for the chart? Thanks!
I'll dig it up. thanks for the suggestion.
Dear friend. I have the document but don't know how to post it. Do you have any suggestions?
@@bensonfilmworks7595 Not sure. Can you post a link to it for Google Drive or some other storage location?
@@bensonfilmworks7595 If you are willing and able, you could email it to me at contact@lenze-enterprises.com
THANKS!
What I don't see here in TX accessible menu is motor timing that it is accessible from programing card, but I'm not sure if it is needed for max efficiency airplane..?
I believe "angle of entrance" is the same as "timing"
Timing is different for inrunners, sometimes ESC goes up in smoke at start up.
❤❤❤
help,my motor won't come on until 50% throttle position
I had the same effect when I powered up the model for the first time.
Then I performed the first step of the programming procedure (= throttle) and now it works.
Did you try this?
@@martinpi11 finally got it going,thank you
thank you
thank you