This is a beautiful mockery of how to restore an old diesel motor. The level of detail is exquisitely painful, and the attention to safety is almost prehistoric. Well done...
You should learn valve lapping some time, it’s worth a fair bit of sealing power and it’s easier than you think, just make sure you can clean it up after
Interesting way to get the torque setting just right on those head bolts. Just pull until the vein in you arm stands proud and you get that first grunt.
No, he lined up the marks on the gears, to be fair to him. I agree otherwise, it pains me that he didn’t even hone the bore let alone measure it and see if it needed a re-bore.
Nice job, but dont paint internals by color. Oil can dissolve color. Pigments are abrasive and could damage bearings and piston rings. If internals of engine was painted originally it was special sealant color for cast iron to prevent oil contamination from cast iron by casting sand. Really NEVER point jet from injector on skin. Fuel can pierce skin.
These dudes are literally buying engines and motors at junk yards, burying them in dirty/mud, then digging them up to "repair" for youtube views. They aren't using these engines. It's entirely for youtube money.
I don't think these Southeast Asian 'restorers' are doing it to make 'serviceable' equipment. If it looks good and starts up and runs for a few minutes to get the 'views', that's good enough. Obviously with 1.5M it must be working! LoL
@@СтаниславФедотов-л8й ну а чё хотеть. Он видео снимает. Он же не поставит его на мотоблок и пахать не станет. Дураки такие же рукожопые скажут что работа проделана отлично, контент понимаешь, хороший
As I said before, there it apart, cleaned it up, put it back together and it runs. You can't ask for more than that. Nicely done gentleman, very nicely done indeed. Texas watches.
@@alanlake5220 Indirect injection does not work at high pressure, since the fuel mixes with the induction air. The latest range of Bosch common rail direct diesel injectors operate at 2,200 bar. (32,300,psi)
Me too , I know oh too well the pressure from an injector nozzle. And I see he replaced some gaskets, but what about the seals , I didn't see him replace any of those.
A wonderful job! An absolutely hideously made engine, no idea why anybody would want one of these. But you took the time and gave it the love it needed to have a working life again, well done :)
"рестовратора" с потрохами выдает покраска привалочных плоскостей, крышки бака. сдергивание коленвала вместе со шпонкой через сальник..хм..молодцы, что сказать.. сильны.
very interesting! those mechanics are extremely clever with all their low-tech tricks like the improvised piston ring compressor strips. that being said, not sure how good an idea it is to let paint get inside the engine, seems like that can dissolve and start wearing surfaces.
I was thinking the same thing. I believe I saw them spray primer and paint on the cylinder wall. I appreciate the new rings, but did they hone? No new main bearings. Then they painted the cylinder head surface.
Wow very amazing!! ,Next time you keep safe your face from cranking the engine it May accidentally smash by the crnking lever ,because of my viewingo on your effort ,it make me remember at my past with using this machine for farming ,so great thank for you
I’ve seen a lot of videos using these engines and it seems like they last forever if taken care of, it doesn’t look like they burn much diesel either! I’d love to have one and run a generator with it! Probably why they’re not sold here in the United States, don’t burn much fuel so that won’t help the fuel industry! lol 😂 just hand crank em and they’re going! Thanks for sharing this video my friend! Always educational to watch! 👌🏻👍🏻👍🏻
Yeah... NO. The only reason this engine doesn't burn much fuel is because most of it leaks past the valves, the cylinder, and the seals! It won't reach high enough RPM's to run a generator, unless you add a gearbox, to convert the torque to speed. Seriously, a modern riding lawn mower has more horse power than this old thing, and weighs less than the whole damned engine...
The best part is when he stuck his hand in the spray pattern when he was "pop testing" the fuel injector, nothing like diesel fuel in your blood stream
👉2:00 Fast bell sound ASMR.... Play that on a 5 hour loop. He doesn't seem too concerned with NOT getting debris into the various wide open components....
Not a good job...not assembled using techniques to extend life (copious oiling of parts like piston rings, painting the insides of the castings...the paint will come off and circulate in the bearings etc...not replacing visibly worn bearings and seals etc. etc.
This was a high tech engine: Plain bearings and 2 balancer shafts. Not sure if those shafts were aligned correctly....the engine seemed jumpy at the end.
This engine has new piston ring, new valves, new nuzzle.it will running good.I like this video!!!
Russian, Chinese, American...who cares. We would all have a blast together and fun times rebuilding old machinery
the video is so awesome. Nice to meet you
Thợ rất phục hồi chuyên nghiệp👍🌾🇻🇳
Wow amazing
I understood that the masters were of good quality because they tightened the bolts mutually. good job.
This is a beautiful mockery of how to restore an old diesel motor. The level of detail is exquisitely painful, and the attention to safety is almost prehistoric. Well done...
The painted gasketed surfaces are what's killing me.
There was absolutely nothing mechanically wrong with this machine. I use these all the time.
You should learn valve lapping some time, it’s worth a fair bit of sealing power and it’s easier than you think, just make sure you can clean it up after
th-cam.com/video/7CuP_8et5eg/w-d-xo.html
9
very dirty...... i like it 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
thank you
Interesting way to get the torque setting just right on those head bolts. Just pull until the vein in you arm stands proud and you get that first grunt.
Or your ring piece pops out.
Over here we tight this half turn before break and that's the torque.
Well, it's Chinese. That's prolly how they did it at the factory.
Yeah just line the gears up any which way it's not like the timing matters. Don't worry about replacing the crankshaft seal either just paint over it.
reuse the old main bearing, which is cooked, as is the surface of the crank journals
@@cheekyrick9529 bloody bush mechanics they are
No assembly lube on any bearing surface, no oil on piston rings; no sealant on those new gaskets...an absolute hack job....
@@cheekyrick9529 u
No, he lined up the marks on the gears, to be fair to him. I agree otherwise, it pains me that he didn’t even hone the bore let alone measure it and see if it needed a re-bore.
您真是天才，這個古老的柴油引擎，您們也可以把它修復，佩服、佩服，給您按鍵讚，100分。
其实发动机完好无损 就是有点脏
古老的东西就是耐用，
Thailand the best👍
คนไทยใหมครรับบ
My indonesia
filled with artificial cement
Nice job, but dont paint internals by color. Oil can dissolve color. Pigments are abrasive and could damage bearings and piston rings. If internals of engine was painted originally it was special sealant color for cast iron to prevent oil contamination from cast iron by casting sand. Really NEVER point jet from injector on skin. Fuel can pierce skin.
Lick đại biết chữ gì đâu
These dudes are literally buying engines and motors at junk yards, burying them in dirty/mud, then digging them up to "repair" for youtube views. They aren't using these engines. It's entirely for youtube money.
P
I don't think these Southeast Asian 'restorers' are doing it to make 'serviceable' equipment. If it looks good and starts up and runs for a few minutes to get the 'views', that's good enough. Obviously with 1.5M it must be working! LoL
th-cam.com/video/SYd4EHOzeDo/w-d-xo.html
I just hope some grease went in all the bearings
Mantap pokok e,, perlu di contoh, kreatif
Когда разбирают мотор с помощью гайковерта - это ещё ладно. Но когда собирают - это нечто! Вьетнамский ремонт называется
А покраска привалочных поверхностей, внутренностей и посадочных отверстий подшипников? Каково, а?)
@@il_magnificoОн только кольца поменял🤣🤣🤣, а сальники и подшибники еще походят🤣🤣🤣, мож еще и прокладки оставил-пускай тоже еще походят🤣🤣🤣
@@СтаниславФедотов-л8й ну а чё хотеть. Он видео снимает. Он же не поставит его на мотоблок и пахать не станет. Дураки такие же рукожопые скажут что работа проделана отлично, контент понимаешь, хороший
As I said before, there it apart, cleaned it up, put it back together and it runs. You can't ask for more than that. Nicely done gentleman, very nicely done indeed. Texas watches.
Considering it will run cooler and be less of a leaky mess, even if it ran before, it’s an improvement
As soon as I saw the Chinese steel-cap boots, and the surgically clean work area, I just knew that I would love this video. Well done guys.
thank you very muck
@@restoration-restore-repair жжж
Kmcka mehnizacij
Ll
.. Hu 8 i u8ii8fni.
.
... .......
Ljubezen podomaccc cc"" ccc
Semangat bang👍👍
Very good job
I've always thought that the hatchet is an undervalued restoation tool
Congratulations! Absolutely AMAZING work! 😳😳😳😁
진정한 재야의. 고수시내
Sehr Geil....gut gemacht .
Wow amazing video great work my friend keep it up good luck who enjoy ❤️ this video hit the like 👍
Похоже, если старый сальник покрасить, он проходит еще очень долго!
Назвать покраску и помывку реставрацией это ж на 700к просмотров) зачем ещё заморачиваться)
Как то внутрянка подозрительно нулевой выглядит
@@ruslanvorontsov7470 на вкладыше износ есть
Да походу очередное наебалово
Xxxun
Never put your hand over a injector to see if it is working
how come? just curious, I only know the basics about diesels
@@dansmith6990 Very high pressure and it will pierce your skin !!
@@alanlake5220 Indirect injection does not work at high pressure, since the fuel mixes with the induction air.
The latest range of Bosch common rail direct diesel injectors operate at
2,200 bar. (32,300,psi)
اللهم صل وسلم وبارك على سيدنا محمد وعلى اله وصحبه اجمعين عمل رائع لا يصدق
unbelievable wonderful work
Pp0
What pp0 ?
Otra excelente restauracion y reparacion lograda en este motor diesel D15, mis respetos y saludos desde Venezuela.
Gracias, buen dia
exellent job looks and sounds great another one back to life well done
Good Job Fellas
I cried inside when they painted it without taping off any gasket surfaces
If you use enough paint, you don't need gaskets.
I did it when they painted the cylinder
Painted seals are my favourite!
@@bobmarker6812 ا
@@bobmarker6812 qeoqrqo
Would love to get such an engine......but I'm in Australia.
Love from Pakistan bro
The second he held his hand in front of the injector I shouted “oh my god!”
Me too , I know oh too well the pressure from an injector nozzle. And I see he replaced some gaskets, but what about the seals , I didn't see him replace any of those.
So did I. NO, dont it will penetrait you skin. Not the doing of a trained mechanic, that knows the power of a diselinjector.
A wonderful job! An absolutely hideously made engine, no idea why anybody would want one of these. But you took the time and gave it the love it needed to have a working life again, well done :)
I like it during the coloring process 👍
Excellent
Once he started the painting process, I had to run to the comments 😅
Вундер машине !
Nah it was the paitning the valves for me
Nice video ☺️
thank you
It looks like archeology project at the beginning :)
Nice job for a low budget rebuild
"рестовратора" с потрохами выдает покраска привалочных плоскостей, крышки бака. сдергивание коленвала вместе со шпонкой через сальник..хм..молодцы, что сказать.. сильны.
Good job mr....
I like it
Mantaf bos👍👍👍
Cảm ơn em đã cho anh xem clip này
hi
Wow very nice
Nice work
Vietnam number1
very interesting! those mechanics are extremely clever with all their low-tech tricks like the improvised piston ring compressor strips. that being said, not sure how good an idea it is to let paint get inside the engine, seems like that can dissolve and start wearing surfaces.
I was thinking the same thing. I believe I saw them spray primer and paint on the cylinder wall. I appreciate the new rings, but did they hone? No new main bearings. Then they painted the cylinder head surface.
Wow very amazing!! ,Next time you keep safe your face from cranking the engine it May accidentally smash by the crnking lever ,because of my viewingo on your effort ,it make me remember at my past with using this machine for farming ,so great thank for you
Sao không phun cát vệ sinh lúc Sơn bền hơn bạn
Excellent video!
A great restoration 👍 but please never put your hand in front of a high pressure injector !
Jip, i think that hand is something of the past, poor bugger
You know its gonna be a good restoration video when theres roosters in the background
I’ve seen a lot of videos using these engines and it seems like they last forever if taken care of, it doesn’t look like they burn much diesel either! I’d love to have one and run a generator with it! Probably why they’re not sold here in the United States, don’t burn much fuel so that won’t help the fuel industry! lol 😂 just hand crank em and they’re going! Thanks for sharing this video my friend! Always educational to watch! 👌🏻👍🏻👍🏻
Yeah... NO. The only reason this engine doesn't burn much fuel is because most of it leaks past the valves, the cylinder, and the seals! It won't reach high enough RPM's to run a generator, unless you add a gearbox, to convert the torque to speed. Seriously, a modern riding lawn mower has more horse power than this old thing, and weighs less than the whole damned engine...
Ttf MN
@@FourDollaRacing He painted the cylinder
GREAT JOB, WELL DONE. I hope you hook it up to a generator. and make some electric.
Hello...i am from indonesian west borneo...good job...i like you channel.
Xixixi
Just another disasembling/cleaning/reassembling video!
If this is "fully restoration", i'am the chinese emperior!
The best part is when he stuck his hand in the spray pattern when he was "pop testing" the fuel injector, nothing like diesel fuel in your blood stream
These injectors are not CRDI. Will mechanical injector create so much pressur to create hypodermic injection?
@@Debraj1978Yes, Only several thousand PSI, depending on the engine make.
Good job bro 👏 👍 👌
nice job
Like anh nha
I like this video 👍👍
Superb. What an effort
Çok güzel oldu
Very patient and professional !!! Great job
Good video
когда ставили новые кольца, поршень надо было почистить от нагара в посадочных бороздах.
ㅡ.
@@방고고싱 ๗ฐ
Как только топор увидел ,все понял....
Of
Mantap, sukses trus buat channelnya
Iya, saya suka Dengan channel ini
@@mbalongchannel3409 เแ
@Subardi Sbd ตตาม
Mantap
Motor is not old,only dirt.😊
Mains looked a tad weary going back together....
th-cam.com/video/7CuP_8et5eg/w-d-xo.html
1，四道活塞环安装的时候应该错开裂口，90度一个，而不是随意位置。2，机油滤杯没打开，里面的滤芯还是脏的。3，既然活塞环都换了，但是轴瓦却没换，缸筒甚至都没拆下来，是我的话，拆成这样子肯定把缸筒随手换了。4，机油泵没看清，按说应该拆下来清洗一下，视频没交代。5，一般来说，曲轴轴瓦接触面，要用细砂纸稍微打磨一下，再上轴瓦。6，最后启动太沉，解决办法是在油泵后面加个垫子，调整供油时间，就会容易摇动了。
오 훌룡하네요 잘보고가요
Excelente,parabéns.
Excelente,pabens.
I wish these guys would restore a pair of shoes.
I'll do that
Hay lắm các anh
cảm ơn nhé. năm mới nhiều may mắn
I thought the head bolts needed a torque wrench to ensure the head seats correctly. Can you not afford it? Great restoration
Objective criticism is good and I've seen evidence that they take note. Such criticism should be given with respect however.
👉2:00 Fast bell sound ASMR.... Play that on a 5 hour loop. He doesn't seem too concerned with NOT getting debris into the various wide open components....
great job
Kerja yg bagus
Valve lapping and for the love of god some body filler on the red pieces!
th-cam.com/video/7CuP_8et5eg/w-d-xo.html
Great job fantastic o
That Samsung notification got me.
ini tuh mesin anti rusak, mau dimandiin lumpur aja gk bakal rusak. itu yg di video jg aslinya gk rusak, cmn kotor aja tp tetep nyala aslinya
Pistonnya aja masih mulus kok wkwkwkw video ngawur
Mój ojciec miał takiego ESIOKA w latrach 1960 - 1990, ciężko owtryski - pozdrawiam.
Paint everywhere, assembling some parts oiled that could be dry and other left dry when they should be oiled, what a laugh 😆
No mo hi
3:48 this is already going so much better than your other video that I’m upvoting already
3:00 PARABÉNS PELO SEU KKK KKK KKK KKK
anh thợ này giỏi quá
Deisel engine restoration using an axe! Who would have thought? He he... nice job.
Hatchet actually
Old machine, and good job
OIdmihne,andgoodjob
Not a good job...not assembled using techniques to extend life (copious oiling of parts like piston rings, painting the insides of the castings...the paint will come off and circulate in the bearings etc...not replacing visibly worn bearings and seals etc. etc.
Buen mecánico le admiro su talento y siga adelante
This good
Công nghệ cao đấy
This was a high tech engine: Plain bearings and 2 balancer shafts. Not sure if those shafts were aligned correctly....the engine seemed jumpy at the end.
Salam kenal dan salam sukses selalu bang