my doesn’t have the sensor you show at the beginning it’s just a hole 😅 but I have the control with the symbol , I ready check the rest and they fine and I try to search it but I can’t find it any suggestions sr ?
Double check that hole to make sure the sensor didn't fall through into the cavity. If none of my tips helped then a scanner that can read the Body Control Module (BCM) is your next step. Everyone should have their own scanner amzn.to/42aC28y especially if your car is no longer under warranty.
Will the dash display if my hood is open or unlatched? I have both of those sensors I just can’t tell if they’re working or not when I press remote start it locks and lights flash but never starts. This is on a 2014 dodge challenger SXT
Get a decent ODB2 scanner on Amazon, one that can read body control module codes (BCM) and see if there are any errors being thrown. This will make short work of troubleshooting. This is a good scanner amzn.to/48QzfVW for a good price that can do it all! You will save hours and headache and skip the high mechanic costs!
Your wiring is shorted, or the connectors need to be unplugged and plugged back in to ensure proper connectivity. dot.report/dtc/U0416 You need a wiring diagram to determine the wiring location and pathway
Remote start on a manual requires a neutral position sensor to ensure the car is actually in neutral before attempting the start. Sometimes, this can be accomplished by fooling the computer to think that the clutch is pushed in, when it's really not. They likely sell kits for this, might require a custom ECU mod or flash. If you have any warranty then don't flash because they voids and they have a flash tracking logger.
There are two hood sensors, one at the latch, and one at the back left near the hydraulic arm. Inspect them for damage, misalignment, corrosion, connectivity.
If not the battery in the fob check your fuse box in your trunk there’s one that deals with all of the wireless stuff like that just look at a diagram online to see which one
When you remote start, you cannot unlock the door or trunk using the remote, if you use the remote the car will turn off. This is to prevent accidental unlock when you're not near the car. If you open the door by hand and then it shuts off, this is not normal. Simple solutions first, replace the battery in your remote and try. Disconnect battery for 30 mins, try again. Get a scanner from Amazon that supports BCM (body control module) code reading and reset. See what codes the BCM is throwing. Keep the scanner or return it, your call. The fix could be simple. Also try to open passenger door and see what behavior that produces.
@TrickMasterPC thank you for the quick response. Both batteries are new, car and remote. I forgot to mention, when I bought the car, the delar sent someone to install LoJack. Since then, I believe the problem had started.
Yeah, it will do that as long as the check engine light is on. Get a scanner and determine the problem. Usually, the issues are easy and cheap to fix. Or take it to the dealer if you want.
@@TrickMasterPC what’s weird is that the first time it threw the light, it cleared off by itself in like 2 days. Now it came back again after a couple of Months and the light hasn’t shut off for about 2 weeks now. And thanks for the help 💪🏾
Absolutely no freaking help , the battery? Or not enough gas really , then I started to read the comments ,oh now I get there all dumbass so you can show a nice car and talk nonsense while walking around gas gossler (by the way is my favorite car my wife will not let me drive hers) and you look cool unfortunately,my wife knows I’m not cool and she won’t go for me walking around her car asking her stuff like, Do you have it on the correct radio channel, Not knocking you it’s good work if you can get ,I’m just jealous lol
Get a good scanner. Scan the body control module codes. If the hood, trunk, door, or window sensors are throwing open or errors, then that will also prevent remote start. If your BCM has a lost comm or connection to ECU error logged, then check the cable connections. Sometimes, intermittent connection drops also cause the issue.
Muchas gracias. Excelente explicación.
my doesn’t have the sensor you show at the beginning it’s just a hole 😅 but I have the control with the symbol , I ready check the rest and they fine and I try to search it but I can’t find it any suggestions sr ?
Double check that hole to make sure the sensor didn't fall through into the cavity. If none of my tips helped then a scanner that can read the Body Control Module (BCM) is your next step. Everyone should have their own scanner amzn.to/42aC28y
especially if your car is no longer under warranty.
Did you ever find your sensor that’s supposed to be under the hood ?
Why do my car lights blink six times when I try to remote start it? It says nothing on the dash at all im just not sure why it blinks six times?
Will the dash display if my hood is open or unlatched? I have both of those sensors I just can’t tell if they’re working or not when I press remote start it locks and lights flash but never starts. This is on a 2014 dodge challenger SXT
Get a decent ODB2 scanner on Amazon, one that can read body control module codes (BCM) and see if there are any errors being thrown. This will make short work of troubleshooting. This is a good scanner amzn.to/48QzfVW for a good price that can do it all! You will save hours and headache and skip the high mechanic costs!
Should I be concerned about the battery? The Harman Kardon system....in the long run
So far I've had zero issues. The dealer disconnected and reconnected all cables and that solved the issue.
I’m having a U0416 code and my guy can’t install the aftermarket remote start it’s 6speed as well any advice would be appreciated highly
Your wiring is shorted, or the connectors need to be unplugged and plugged back in to ensure proper connectivity. dot.report/dtc/U0416
You need a wiring diagram to determine the wiring location and pathway
Remote start on a manual requires a neutral position sensor to ensure the car is actually in neutral before attempting the start. Sometimes, this can be accomplished by fooling the computer to think that the clutch is pushed in, when it's really not. They likely sell kits for this, might require a custom ECU mod or flash. If you have any warranty then don't flash because they voids and they have a flash tracking logger.
Does the Chrysler 300 have both sensors for hood open code ? I can’t seem to find the one Next to the cabin filter @trickmaster
I think it is in the latch on 300s
Mine start and shut down then shows on the dash. Remote start cancelled hood open. but its not any suggestion
There are two hood sensors, one at the latch, and one at the back left near the hydraulic arm. Inspect them for damage, misalignment, corrosion, connectivity.
Ty bro
What do I do if my key fob does not work at all, not the lock button, unlock button, or remote start
new battery's for the key fob
If not the battery in the fob check your fuse box in your trunk there’s one that deals with all of the wireless stuff like that just look at a diagram online to see which one
So, my car remote start works but it shuts off right when I open the door. Is that normal?
Also, I used to be able to open the door without the car shutting off
2016 Dodge Charger
When you remote start, you cannot unlock the door or trunk using the remote, if you use the remote the car will turn off. This is to prevent accidental unlock when you're not near the car. If you open the door by hand and then it shuts off, this is not normal. Simple solutions first, replace the battery in your remote and try. Disconnect battery for 30 mins, try again. Get a scanner from Amazon that supports BCM (body control module) code reading and reset. See what codes the BCM is throwing. Keep the scanner or return it, your call. The fix could be simple. Also try to open passenger door and see what behavior that produces.
@TrickMasterPC thank you for the quick response. Both batteries are new, car and remote. I forgot to mention, when I bought the car, the delar sent someone to install LoJack. Since then, I believe the problem had started.
I got 2022 charger RT
Check engine light is on and remote start works for few seconds then turned off
Yeah, it will do that as long as the check engine light is on. Get a scanner and determine the problem. Usually, the issues are easy and cheap to fix. Or take it to the dealer if you want.
Yeah i got the same problem. Update if you have got your issues fixed
@minimumday get a decent scanner off amazon. Check your DTC engine codes to see whats faulty. Fix the fault then clear the codes.
@minimumday check all hoses, electrical connectors, gas cap etc. Simple things that could throw an engine code. Otherwise you'll need a scanner
@@TrickMasterPC what’s weird is that the first time it threw the light, it cleared off by itself in like 2 days. Now it came back again after a couple of Months and the light hasn’t shut off for about 2 weeks now. And thanks for the help 💪🏾
But it works when my car is on
Is it possible you have one of ur spare remotes in the car somewhere?
No I only have 1 remote
The battery is fresh? Take apart the remote and clean it. Sometimes lint, dirt, moisture gets inside. Simple solutions first
@@TrickMasterPC yessir the battery is brand new, I’ll try to clean and see what happen
Absolutely no freaking help , the battery? Or not enough gas really , then I started to read the comments ,oh now I get there all dumbass so you can show a nice car and talk nonsense while walking around gas gossler (by the way is my favorite car my wife will not let me drive hers) and you look cool unfortunately,my wife knows I’m not cool and she won’t go for me walking around her car asking her stuff like, Do you have it on the correct radio channel,
Not knocking you it’s good work if you can get ,I’m just jealous lol
Get a good scanner. Scan the body control module codes. If the hood, trunk, door, or window sensors are throwing open or errors, then that will also prevent remote start. If your BCM has a lost comm or connection to ECU error logged, then check the cable connections. Sometimes, intermittent connection drops also cause the issue.