Thanks for the video, I’ve got everything work, but for some reason, the current/amps only reports 0? This is even under prop load. Amps/current is ticketed in the telemetry, and it also appears to not show when down loading the logs too, any ideas? Phoenix Edge 80HV
I don't have FASSTest System yet, but my Su-31 is equipped with an Edge 75, I was just seeing what the telemetry was capable of. I will upgrade to a 18SZA or 14SGA in the future, so it would be nice to get the telemetry link too. Would try to put them on a flat foamy with a Talon 15 too, its lighter than a voltage sensor for the battery.
Question? I have the 16sz and I order the castle telemetry sensor and I did the mode change on the receiver to mode 2 like you showed here I plug the wire from the sbus2 from the receiver to my Ikon unit and I am using an old Ikon unit not the newest so when I get the castle sensor where do I plug the white red and black cable on channel 8 sbus? I don’t run bec I use an 2s battery to power my receiver servos fbl etc completely separate is my prefer method. Thank you in advance.
great video. Im running the 160 and cgy750 as well. how did you run the Sbus wire? I have my Sbus wire from my 750 going into my R7008SB Rx Sbus slot. So how would I wire the telemetry when its being used to link my rx? thanks
under the castle TLO RPM sensor , i entered the motor magnetic pole and gear ratio but the castle creation telemetry is not convertion the motors RPM to head speed. it's displaying the motor rpm. can you help.i am using the futaba 18sz & R7003sb
Hi Chris, in CGY750, it use CH 8 for Governor on/off and CH9 for Gyro2 (Ail Gain), and Castle Telemetry Link use CH8-15. Is it necessary to switch Gyro2 to other Channel ? Thanks.
so, for the castle telemetry link you don't need to buy the Futaba External Voltage Input Cables , because it shows everything. look at the link below. www.towerhobbies.com/cgi-bin/wti0001p?&I=LXCFVY&P=ML
Just brought the telemetry link and watched the presentation again to install it. Spot on. Thanks.
Steve Kennett awesome, glad the video helped!
Thanks for making this video! It was a huge help with setting up the Castle Telemetry Link on my new Futaba 16IZ transmitter.
Awesome job man. This made setting things up so much easier. Thanks!
As usual.. Great job Chris!
Excellent one of the best... Thanks
Just what I needed to get the Castle Telemetry Link to work on my Futaba T18MZ. Recommended video by Joe at Castle Support.
Thanks for the video, I’ve got everything work, but for some reason, the current/amps only reports 0? This is even under prop load. Amps/current is ticketed in the telemetry, and it also appears to not show when down loading the logs too, any ideas? Phoenix Edge 80HV
I don't have FASSTest System yet, but my Su-31 is equipped with an Edge 75, I was just seeing what the telemetry was capable of.
I will upgrade to a 18SZA or 14SGA in the future, so it would be nice to get the telemetry link too. Would try to put them on a flat foamy with a Talon 15 too, its lighter than a voltage sensor for the battery.
Question? I have the 16sz and I order the castle telemetry sensor and I did the mode change on the receiver to mode 2 like you showed here I plug the wire from the sbus2 from the receiver to my Ikon unit and I am using an old Ikon unit not the newest so when I get the castle sensor where do I plug the white red and black cable on channel 8 sbus? I don’t run bec I use an 2s battery to power my receiver servos fbl etc completely separate is my prefer method. Thank you in advance.
great video. Im running the 160 and cgy750 as well. how did you run the Sbus wire? I have my Sbus wire from my 750 going into my R7008SB Rx Sbus slot. So how would I wire the telemetry when its being used to link my rx? thanks
The 7008 Rx had two sbus ports. You have to change the mode in the RX to turn the second one on. Check the manual. I haven’t don’t it in a while.
@@cdsexton1 thank you...all this time i didnt realize it had 2 sbus ports. thank you thank you
under the castle TLO RPM sensor , i entered the motor magnetic pole and gear ratio but the castle creation telemetry is not convertion the motors RPM to head speed. it's displaying the motor rpm. can you help.i am using the futaba 18sz & R7003sb
nivasyl strongman make sure the radio, TLO, and esc have current firmware. This was a problem in the early releases but was patched.
Hi Chris, in CGY750, it use CH 8 for Governor on/off and CH9 for Gyro2 (Ail Gain), and Castle Telemetry Link use CH8-15. Is it necessary to switch Gyro2 to other Channel ? Thanks.
Gary Lau sensor sockets don't conflict with RX channels. You're fine.
Can you also se mAh drawn like on jLog. So you know when its time to land ? :D
so, for the castle telemetry link you don't need to buy the Futaba External Voltage Input Cables , because it shows everything. look at the link below.
www.towerhobbies.com/cgi-bin/wti0001p?&I=LXCFVY&P=ML
lys avin nope
i am glad i watch you video. cause, i was about to buy one from tower Hobby. LOL
you speak to fast. you said your name is chris from team what?????????????????