@@smaabaadsnyt-altomsmabadeo9300 Having a hard time putting the lower unit back on - seems to be the gear selector rod that's the problem. It would not locate if left on the lower unit, so we took it off and managed (after lots of fumbling) to mate it to the upper, but still having problems putting the lower unit back on. Was hoping for a bit more detail than the jump cut at @3:41 😉 Update: Turned out putting in the selector rod first was the problem - there was so much resistance mating it with the lower housing that it was impossible doing it while putting the lower housing back on. After pulling the rod out and having to use a hammer to put it back on to the lower housing spline, we did manage to get the lower housing back on without too much trouble.
Clean the shaft before sliding new impeller on. Do not grease the impeller housing. No need. That's what water is for. Grease and water.... do not mix. If you want to use something use a little WD-40 or a little dish soap... not grease. Just sayin:-) But for sure great the impeller shaft.
should at least talk about what his doing...most of us or me are first time at this and hearing music and him going thru the motions without eplaining it does not help one bit
@@highspeed3312 Obviously the guy is from Denmark, and probably doesn’t speak English, genius. So if he did speak, you’d be whining about how he didn’t speak ‘murican, so you could understand. A picture, or a video clearly demonstrating what he’s doing is worth a thousand words. If you don’t like his video, watch another one, or make your own, jackass..
Good video. The only thing I see you didn't show was hooking back up the speed o tube.
This was great, thank you!
Helpful video. What kind of grease do you use?
Hi - I think every marine grease will be ok
A good video but a narrated one would have been better,
Should I put the motor in gear before I do this or leave it in neutral. I know some older outboards need to be in gear to help align the splines
Hi - when I did it it was in neutral 🙂
@@smaabaadsnyt-altomsmabadeo9300 Having a hard time putting the lower unit back on - seems to be the gear selector rod that's the problem. It would not locate if left on the lower unit, so we took it off and managed (after lots of fumbling) to mate it to the upper, but still having problems putting the lower unit back on. Was hoping for a bit more detail than the jump cut at @3:41 😉
Update: Turned out putting in the selector rod first was the problem - there was so much resistance mating it with the lower housing that it was impossible doing it while putting the lower housing back on. After pulling the rod out and having to use a hammer to put it back on to the lower housing spline, we did manage to get the lower housing back on without too much trouble.
Non sviti il bullone sotto la pinna direzionale???
isn't there a clip ontop of the thiner shaft that needs removing thank you
As I remember it there isnt
Clean the shaft before sliding new impeller on. Do not grease the impeller housing. No need. That's what water is for. Grease and water.... do not mix. If you want to use something use a little WD-40 or a little dish soap... not grease. Just sayin:-) But for sure great the impeller shaft.
WD40 destroys rubber, silicone spray/grease is good
soap
..and small grease on bolt, the bolt hole is not open.
Graso is prohibited my friend....you have to read more
should at least talk about what his doing...most of us or me are first time at this and hearing music and him going thru the motions without eplaining it does not help one bit
music is too annoying to watch
That’s what your volume control is for. The guys not even talking - just showing. Turn your volume off. You’ll be okay, I promise.
@@AMylander is that what's it's for. Dang...thanks genius. Usually how to videos, you explain what you're doing ...jackass.
@@highspeed3312 Obviously the guy is from Denmark, and probably doesn’t speak English, genius. So if he did speak, you’d be whining about how he didn’t speak ‘murican, so you could understand. A picture, or a video clearly demonstrating what he’s doing is worth a thousand words. If you don’t like his video, watch another one, or make your own, jackass..