Nice drill. I'd love to play with that for just one week. Hilti is pricey but they sure make some quality equipment. I think a lot of the time the guys that bitch about the cost of their products are really just jealous maybe. I'm one of them I can honestly say. I can still remember the first time I used a 480v drill. It was the pentruder model. I drilled an 8" dia. 12" deep.....45 seconds. I thought I was dreaming. Nice job man.
I know this the DD500 but have you heard that a DD350 was used to break into a vault in London? Media is currently estimating the theft could be as much as £200 million but they aren't sure yet, as it was a 'safe' deposit. Yours is the most detailed video I've found that could be used as a DIY guide....wonder if they used your video?? The wall was 2m thick....can you get extensions for these? Or do you think they had to make their own?
Yes, you can core drill almost any depth, all manufacturers sell extensions, sometimes long barrel core bits are made up or ordered for thick drilling.
RA30st08 The HILTI could do it, through concrete, same bit more extension. But apparently the 'heist' was 2m through reinforced concrete rebar, and you'd have to be 4yo small to get through a 350mm, 2m long tunnel. Imagine a 30cm ruler held out infront of you.
I think they must have drilled a series of holes to create an opening, i'm guessing at least 600 mm in diameter. that would require around 19 holes at 100 mm, looking at 45 per hole.
Elizabete geraldina silva Meu nome é Elizabete trabalho com Desentupimento e Hidráulica na Empresa SDB e quero saber se ela trabalha também caixas visita na hidráulica? quanto custa e forma de pagamento,se é a diesel,e quanto tempo trabalha por litro e posso trabalhar onde existem pontos com pedras.
I noticed all tools have close resemblances the color and name brand are the two differences, the wanker using the tool is what really matters. SAFETY FIRST MATES👷 cheerio
Bertie Blue You have to drill to the full depth of the barrel and then use a wedge to snap the core and pull it out.Add an extension to the bit and drill again, repeat until through the wall.
"Some people would kill for an ass like this." lol
Nice drill. I'd love to play with that for just one week. Hilti is pricey but they sure make some quality equipment. I think a lot of the time the guys that bitch about the cost of their products are really just jealous maybe. I'm one of them I can honestly say. I can still remember the first time I used a 480v drill. It was the pentruder model. I drilled an 8" dia. 12" deep.....45 seconds. I thought I was dreaming. Nice job man.
Hatton Garden Heist brought me here ;)
Every bank robber in the world is watching this video ;P
My god, what a buzz that must have been, crawling out of the hole inside the vault.
I know this the DD500 but have you heard that a DD350 was used to break into a vault in London? Media is currently estimating the theft could be as much as £200 million but they aren't sure yet, as it was a 'safe' deposit.
Yours is the most detailed video I've found that could be used as a DIY guide....wonder if they used your video?? The wall was 2m thick....can you get extensions for these? Or do you think they had to make their own?
Yes, you can core drill almost any depth, all manufacturers sell extensions, sometimes long barrel core bits are made up or ordered for thick drilling.
That's why I'm here I wanted to see how could this drill get through the safe
RA30st08 The HILTI could do it, through concrete, same bit more extension. But apparently the 'heist' was 2m through reinforced concrete rebar, and you'd have to be 4yo small to get through a 350mm, 2m long tunnel. Imagine a 30cm ruler held out infront of you.
I think they must have drilled a series of holes to create an opening, i'm guessing at least 600 mm in diameter. that would require around 19 holes at 100 mm, looking at 45 per hole.
kollenberg74 Wonder if they got a kid or dwarf in on it....just like Bad Santa lol
Rob, this happens all the time.
the wall is 20 some years old.
we are drilling the holes for equipment upgrades.
This drill must draw quite a bit of power under load. If you tried making a hole in an Italian bank vault you would end up tripping the whole street.
Brilliant, hope they don't get caught.
Very good !!
It is Hilti Co. The poor operator should be sitting under an umbrella branded with Hilti logo.
Do they go around in tangerine colored vehicles? They do here in the Philippines
So this is probably the video the robbers used....lol.
***** hmmm i should get a cut
Elizabete geraldina silva
Meu nome é Elizabete trabalho com Desentupimento e Hidráulica na Empresa SDB e quero saber se ela trabalha também caixas visita na hidráulica? quanto custa e forma de pagamento,se é a diesel,e quanto tempo trabalha por litro e posso trabalhar onde existem pontos com pedras.
Milwaukee is coming out with an M18 version.
no chance of robbing it now, the owner has installed high tec alarm systems including heat and vibration systems.
Nice drill nice setup...but on big holes just use hydraulics.....check out....core drilling a 43
Wspaniała maszyna.
I noticed all tools have close resemblances the color and name brand are the two differences, the wanker using the tool is what really matters. SAFETY FIRST MATES👷 cheerio
I'm curious if anyone needs a used one of these? I've got one going cheap, only used to drill 3 times. Thx.
How much did you sell it for
Did the concrete guys forget to lay the formwork for this hole or what?
O na sucho może się zatrzeć, jak mawiała pewna dziewczyna 😜
How much cost this hole ?
How much per our? Or for hole
во во и щас на такой машине еду бетоны просто тема советую
crack that vault
3 year experience Concrete cutting machine operator .I need a job
this video doesnt tell which bank to target
Рабочая лошадка
This might b a stupid question, but how do you get the material out after?
whyexactly Ha you didn't watch to the end :)..... drill until almost through then snap the core and pull it out.
Gut
We have the core drill bit for HITLI
how does the "concrete plug" come out?
Bertie Blue You have to drill to the full depth of the barrel and then use a wedge to snap the core and pull it out.Add an extension to the bit and drill again, repeat until through the wall.
kollenberg74 Thanks mate, do you know anything about safe deposit boxes? haha
NICE VID!
Арматура была в бетоне????????????
Came here from imgur like if you did the same
3X 20" holes at 16"
Arrival on site 7:30 packed up at 11:30
thats great time
wtf! what NM torque?
DD 200?
на кой там ключ? патрон от руки должен закручиваться!
он ключиком держит чтобы не вращался патрон
Патрон с такой коронкой провернуть тяжело.
Обычно вставляется коронка в патрон, и гайка накручивается от руки.
обычно-это когда коронка обычная, а тут елдень
E La Madonna !!!
IT MUST BE 380V NOT 480
No it’s 480 Volt
Перфоратор 80 лвл
hilti is the guvnor.hehe
Scott L howmuch
nice video....check out mine.....core drilling a 43"