OMG, I really did i!. Thanks Matt your video was great. I saved $116 by doing it myself. Repair guy would have gladly come over for $49.95 service all plus $80 for repair. for a total of $130. I told him on the phone that I wanted to try it myself first. I bet he said "dang" under his breath, "those DIYers, I just can't fool 'em". I just had to buy an extension for my socket and the part from a local store for my agit dogs (didn't need kit) and I was good to go. My husband has been calling me the "Maytag Repairman" (even though it was a Whirlpool). THANKS AGAIN MATT!
Excellent! Thank you. You turned what would have been days of unnecessary work, expensive spend and frustration into a simple and enjoyable task. I gladly buy you the parts this time and will come back next time one of my appliances breaks down. Congratulations for a work very well done.
You folks are the greatest, to see the repair completed along with the explaination is just too good. Or SIMPLY BRILLIANT as the Brits would say. Please carry on. B.J. Ackley
The video was great. Very informative and easy to follow. We discovered the "dogs" were broken and had the problem fixed in no time. Thanks so much for posting this!
Thank you for a thorough and detailed video. Unknowingly, I removed the base tabs per the installation instructions for the Thrust Washer Kit 285587 that was in the Agitator Repair Kit for 285811. grrrrr!! When I contacted Whirlpool they put the incorrect instructions in the 285811 kit, they would not assist and told me to look on TH-cam for how to reinstall the auger to the agitator. Since you mentioned this detail to install the agitator and auger separately, you have save me considerable hours of frustration thinking I did something wrong. Thanks for your video!!!
On Thursday Sept 12th I ordered the parts, on Friday Oct 13 the parts arrived at my home and just now we installed the pieces!!! OMG you and your company are GREAT seriously the BEST!!! thank you so much!!!
Three observations: First, these videos are outstanding. You can save a lot of money by watching and following along as Matt describes each step. Second, I'm introducing these videos as part of a new drinking game. It's simple: Every time Matt says "go ahead," everybody takes a drink. ;) Third, I'm naming the new band "Agitator Dogs."
Thanks for this great video, can the agitator make the machine shake alot like its off balance? When its spinning, the machine whats to walk around and if I hold the agitator while its spinning its all good
Most times if the washer wont spin it is the lid switch, it acts like a safety switch that stops the washer from spinning if the lid is open. If it is failing or damaged it may be working intermittently.
Check the pump and drain lines for any obstructions that would stop the machine from draining. You could also have a bad clutch/brakes that could cause the drum not to spin up to full speed, which would make the clothes come out wet. You can go to our forum and do a search for " Replacing direct drive washer brake shoes" this will give you the thread that gives all the info about the brakes and clutch.
Marco Myre, I cannot respond as you have the reply feature off. I would start with checking to be sure all the feet are level. Then check the springs and the support structure. The agitator should not really cause an off balance issue but make sure you check it for damage or wear.
Most washers are off level because their feet are not adjusted to the floor. On this type of washer the rear legs are self adjusting and the fronts need to be adjusted with a wrench. To adjust the rear feet you have to tilt the washer forward so the rear feet are off the ground this lets the rear feet drop down, then lower the washer, they lock in place as they touch the floor. Make sure the rubber pads on the feet are ok. If the legs check out it could be a more serious suspension issue.
Thank you so much for this informative video. You made it look so easy. I purchased the repair kit from your website and installed the parts in less than 15 mins. I'll take the cost of the parts over an expensive repairman any day. Do me a favor though, don't tell my wife that it was this easy.
That's great! Subscribe to our channel to stay up to date as we post new videos. We also have playlists for our washer repairs and our dryer repairs, if you want to keep up with those in particular. :)
Hi, My Kenmore top loader washer works fine but at the end of spinning cycle it makes a radling, banging sound this started after I fixed a waterleak in the plastic tub, I did replace one of the springs because of rust. Any suggestions? Thanks Bart
Replaced the dogs with a repair kit and I'm still not getting any agitation. The top auger engages the bottom agitator now that the dogs are replaced, but the latter has worn splines. Would that keep it from functioning? I already ordered a new bottom agitator, but is there something else I'm missing? The machine makes all the right noises like it's working, but if I crack the lid and peak in, nothing is happening.
I love DIY repair videos, and these are very good. My Whirlpool (Kenmore 110.20912991) actually has a significant difference in disassembling, as there is a plastic retainer that must be removed (using a 1/2" socket drive) before gaining access to the 7/16" bolt. Also, I'm wondering why not just replace the agitator dogs (for about $3), versus the entire agitator cam repair kit (about $17-$25, depending on your model)?
I hope you are still reading the comments. My two agitator parts are already separated so how do I put them back together so the top is bolted to the bottom? I must be missing something that connects the two because I can take out the bolt out without going down the top part of the agitator. I have the items you show excluding the dust cover. Do I need to order that? I just can't figure out why my two agitator sections are already apart. The previous owner must of and that's why it felt like it was flopping around and not snug. If you read this I would greatly appreciate your help! Thanks!
I'm pretty sure I'll be able to fix my agitator now...thanks! Question: is white grease the same as white lithium grease? I (google) searched for white grease and all I'm seeing is white lithium grease.
Thank you - I see that you do also have a video for just replacing the agitator dogs, in case the other agitator components are still good. Guess I need to figure out how to search better. Good on ya!
I bought the repair kit and replaced the dawgs and it seams to work properly. When I wash a load the dawgs are still slipping. The teeth on the upper adgitator are not broke or worn out as far as I can tell. I used vasoline instead of adgitator grease. Any suggestions ?
I have an older g.e. washer that leaks terribly underneath. I have reached under it, and found that the "boot" that seals the bottom of the tub is not in place. Looking back over the years, I seem to remember fixing this problem on another washer, but I cant even get the agitator off of this one. I can see that it is on a spline shaft, because the tip of the agitator is broken off which would indicate to me that it comes straight up. I tried straps, and a 7 foot 2x4 lever, but it won't budge.
Those boot seals have been discontinued by G.E. but are available aftermarket, here is the part number to enter on our site: AP5183580. As far as getting the agitator off that's another story, they used to make a water bladder that you could put under it to get it off but I don't think you will find one, as these machines haven't been made for about 20 years. I would say let some penetrating oil sink in and try the straps again.
i have a maytag hav2360aww model how can i move the body to check if the motor is burnt my washing machine stop from working on the last cicle and smell like rubber burning . need some help i don't have a clue if is the motor or the belt any help i will appreciate. thanks
My washer wont agitate but will spin. I have a maytag centennial commercial technology and I have checked the dogs which are fine, I have checked the motor cuplets and the clutch assembly is just fine I don't know what the problem is. Is there anything you can tell me to check next. Just the machine wont agitate and everything else is fine. I don't spin as fast but it will spin.
This video is for a Whirlpool style washer. The GE agitators are sold all as one piece. You can go to our web site and enter your model number to see the parts breakdown.
I have the same problem. My dust cap doesn't have a handle to grab and lift. i am sure that if I could get it off , my problem would be solved. I need help! I have a GE model wwse5240g1ww
Ryan Marquis They can get stuck together pretty good. As long as it is the type in the video you should be able to pull it apart. There are ones do not come apart so double check!
+Jack Wagner You can try putting some warm water in there to try and get the gunk to let go. Also try a small screwdriver in between the cap and the side of the upper agitator, to try and break it free.
IF I HAVE A WASHING MACHINE OFF BALANCE WHAT CAN I DO TO FIX IT AND STOP THE THE LOUD NOISE! I WANT TO MAKE MY WASHER QUITE AGAIN!!!! PLEASE ADVISE ME ON WHAT SHOULD I DO!!! PLEASE OR WHERE I COULD GO TO HAVE SOMEONE FIX IT!!
I can wash a load a clothes it sometimes it will wash, drain and spin with no problem, Then sometimes I'll wash a load it will wash, drain then it won't spin. What could be causing it? Thanks..
sugar baby This repair is for the upper agitator. If yours fell off it could just be the bolt came loose. If not check the lower half for any wear or damage especially the splines where it connects to the transmission shaft.
babe ruth There are a few designs they have used over the years. You can go to our site and enter your model number to view the parts breakdown. You can also post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem.
my washer doesnt drain the load completely... clothes were still soakin wet but it spins after the rinsing cycle... whats wrong with my washer pls??? HELP!!!
Wanda Vazquez You can post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. You can also go to our site and enter your appliances model number to view the parts breakdown, to see how it comes apart.
Ahmad Shanniek You should only have to grease the thrust washer. If you greased the whole thing there is a chance you could get grease on your clothes. A lot of grease may also interfere with the dogs swinging in and out.
+Davida Watkins If you need repair help it is best to post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
AppliancePartsPros I just found out mine is a 1991 model and doesn't have a collar or ring.. The dogs are just sitting in the gear. Working fine so thank you very, very much.
I replaced the agitator only at the top and it still wont spin what I'm I doing wrong? Does the volt have to be tighten more or should I also do the button
thanks so much for the video , I been trying like hell to find a great video that explains how to do this , my problem though is I need to know the part number I have called everyone including sears and thoe customer care people don't know jack. they doing the same thing I was doing looking on their site and giving me the wrong part number , one guy actually gave me the number for the upper agitator ,when I asked him the number for the kit , I didn't realize his mistake until I looked up the part on there site , just ridiculous. so I wonder can you please help me . I have a Kenmore 800 .. the model number is 110.28847700 . I need to replace the kit , like you just did in the video, and that part looks exactly like the one I took out my machine. I just need to know the correct part number for that kit so I can order and get back to using my machine again . thanks for your help it would really really be appreciated a whole bunch
We're glad to help, Ray! This is the correct agitator kit for your machine: www.appliancepartspros.com/whirlpool-auger-agitator-asm-wp8578210-ap6013533.html
Morning I try to register to put my question in it is hard to register all I need to know is to pull the transmission of the the tub I get the nut loose but transmission would not come loose please help ge stackable washer and dryer model number gtun275em2ww or gtun275em1ww serial number afo10155c I need your help please the washer is leaking badly I try to register it didn't go through thank you in advance
We are limited on what when can do here, we have a limited amount of response space. If you need more in depth help you should register with the repair forum. Here is a picture if a transmission used in those styles of washers, as you listed 3 different model numbers in your 2 questions I do not know if it is the correct one for yours. It looks like it comes as the whole support assembly, it is mounted with a lot of bolts from the bottom. www.appliancepartspros.com/ge-supports-assy-wh16x10186-ap5788202.html www.appliancepartspros.com/motor-drive-assembly-parts-for-ge-gtup270em0ww.html
morning I have a new ge stackable washer and dryer my tub a leak I need to no how to pull apart the tub and the transmission thanks in advance model number gtup275emoww
That is way more than we can cover here. I would suggest posting the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
OMG, I really did i!. Thanks Matt your video was great. I saved $116 by doing it myself. Repair guy would have gladly come over for $49.95 service all plus $80 for repair. for a total of $130. I told him on the phone that I wanted to try it myself first. I bet he said "dang" under his breath, "those DIYers, I just can't fool 'em". I just had to buy an extension for my socket and the part from a local store for my agit dogs (didn't need kit) and I was good to go. My husband has been calling me the "Maytag Repairman" (even though it was a Whirlpool). THANKS AGAIN MATT!
+Tammy OConnell Awesome, Glad the video helped you get the washer fixed and save some money!
WOW 2024 and this video just saved my butt. Got the proper parts and used the video as a guide. I owe you guys a round of coffee!!
Glad you were able to fix your issue! If there is anything we can help you with in the future please let us know.
Excellent! Thank you. You turned what would have been days of unnecessary work, expensive spend and frustration into a simple and enjoyable task. I gladly buy you the parts this time and will come back next time one of my appliances breaks down.
Congratulations for a work very well done.
You folks are the greatest, to see the repair completed along with the explaination is just too good. Or SIMPLY BRILLIANT as the Brits would say. Please carry on.
B.J. Ackley
The video was great. Very informative and easy to follow. We discovered the "dogs" were broken and had the problem fixed in no time. Thanks so much for posting this!
Thank you for a thorough and detailed video. Unknowingly, I removed the base tabs per the installation instructions for the Thrust Washer Kit 285587 that was in the Agitator Repair Kit for 285811. grrrrr!! When I contacted Whirlpool they put the incorrect instructions in the 285811 kit, they would not assist and told me to look on TH-cam for how to reinstall the auger to the agitator. Since you mentioned this detail to install the agitator and auger separately, you have save me considerable hours of frustration thinking I did something wrong. Thanks for your video!!!
I watched 10 of these video's and you are the only person that mentions grease and where to put it. Great detail, thanks.
mrrglo1 Glad they video helped you get the agitator kit installed!
On Thursday Sept 12th I ordered the parts, on Friday Oct 13 the parts arrived at my home and just now we installed the pieces!!! OMG you and your company are GREAT seriously the BEST!!! thank you so much!!!
Worked like a charm. Great video! Took me longer to gather the tools than it did to do the job.
You are awesome! I ordered the parts from your store, they were delivered on the second day, 10 minutes later I'm washing laundry! Thank you so much!
+Cheryl Poll Thanks for the order and glad the video helped you out!
Three observations:
First, these videos are outstanding. You can save a lot of money by watching and following along as Matt describes each step.
Second, I'm introducing these videos as part of a new drinking game. It's simple: Every time Matt says "go ahead," everybody takes a drink. ;)
Third, I'm naming the new band "Agitator Dogs."
Thanks for this great video, can the agitator make the machine shake alot like its off balance? When its spinning, the machine whats to walk around and if I hold the agitator while its spinning its all good
Most times if the washer wont spin it is the lid switch, it acts like a safety switch that stops the washer from spinning if the lid is open. If it is failing or damaged it may be working intermittently.
Check the pump and drain lines for any obstructions that would stop the machine from draining. You could also have a bad clutch/brakes that could cause the drum not to spin up to full speed, which would make the clothes come out wet. You can go to our forum and do a search for " Replacing direct drive washer brake shoes" this will give you the thread that gives all the info about the brakes and clutch.
Marco Myre, I cannot respond as you have the reply feature off. I would start with checking to be sure all the feet are level. Then check the springs and the support structure. The agitator should not really cause an off balance issue but make sure you check it for damage or wear.
This video was very helpful. I give it 5+ stars. My washer is back to agitating. Thanks so much.
Most washers are off level because their feet are not adjusted to the floor. On this type of washer the rear legs are self adjusting and the fronts need to be adjusted with a wrench. To adjust the rear feet you have to tilt the washer forward so the rear feet are off the ground this lets the rear feet drop down, then lower the washer, they lock in place as they touch the floor. Make sure the rubber pads on the feet are ok. If the legs check out it could be a more serious suspension issue.
This guy is the Bob Ross of appliance repair. I love it.
Matthias Happy little agitator cams!
Thank you so much for doing these videos!!!
You're welcome!
Thank you so much for this informative video. You made it look so easy. I purchased the repair kit from your website and installed the parts in less than 15 mins. I'll take the cost of the parts over an expensive repairman any day. Do me a favor though, don't tell my wife that it was this easy.
Instructions done right! Step by step
Great video. Thank you. You just saved me a lot of money. I was going to buy a new washer. I just ordered the complete kit for under $20. :)
I love washers and dryers and this is interesting to watch I get that feeling
That's great! Subscribe to our channel to stay up to date as we post new videos. We also have playlists for our washer repairs and our dryer repairs, if you want to keep up with those in particular. :)
Hi, My Kenmore top loader washer works fine but at the end of spinning cycle it makes a radling, banging sound
this started after I fixed a waterleak in the plastic tub, I did replace one of the springs because of rust.
Any suggestions?
Thanks Bart
Replaced the dogs with a repair kit and I'm still not getting any agitation. The top auger engages the bottom agitator now that the dogs are replaced, but the latter has worn splines. Would that keep it from functioning? I already ordered a new bottom agitator, but is there something else I'm missing? The machine makes all the right noises like it's working, but if I crack the lid and peak in, nothing is happening.
This was awesome! I had my washing machine back up and running properly in no time :D
Because of you I save 150$ thanks a lot !!!
You're welcome!
I love DIY repair videos, and these are very good. My Whirlpool (Kenmore 110.20912991) actually has a significant difference in disassembling, as there is a plastic retainer that must be removed (using a 1/2" socket drive) before gaining access to the 7/16" bolt. Also, I'm wondering why not just replace the agitator dogs (for about $3), versus the entire agitator cam repair kit (about $17-$25, depending on your model)?
I hope you are still reading the comments. My two agitator parts are already separated so how do I put them back together so the top is bolted to the bottom? I must be missing something that connects the two because I can take out the bolt out without going down the top part of the agitator. I have the items you show excluding the dust cover. Do I need to order that? I just can't figure out why my two agitator sections are already apart. The previous owner must of and that's why it felt like it was flopping around and not snug. If you read this I would greatly appreciate your help! Thanks!
What is your model number of your washer?
I'm pretty sure I'll be able to fix my agitator now...thanks! Question: is white grease the same as white lithium grease? I (google) searched for white grease and all I'm seeing is white lithium grease.
"Dogs" is short for Directional Cogs.
Love the video.
Thank you - I see that you do also have a video for just replacing the agitator dogs, in case the other agitator components are still good. Guess I need to figure out how to search better. Good on ya!
gah! I forgot to order grease. Would silicone spray work?
Is there a layer of grease that goes onto the metal bolt/onto the metal of the hub that holds the agitator?
I bought the repair kit and replaced the dawgs and it seams to work properly. When I wash a load the dawgs are still slipping. The teeth on the upper adgitator are not broke or worn out as far as I can tell. I used vasoline instead of adgitator grease. Any suggestions ?
Have you taken a look at the clutch?
@@appliancepartspros no not yet. I tried running it without the agitator and it runs properly but I didn’t have it under a load.
Very helpful! My husband fixed my washer in about 25 minutes for less than $20! Our "dogs" were not grabbing...
Glad the video helped you get the washer fixed!
I have an older g.e. washer that leaks terribly underneath. I have reached under it, and found that the "boot" that seals the bottom of the tub is not in place. Looking back over the years, I seem to remember fixing this problem on another washer, but I cant even get the agitator off of this one. I can see that it is on a spline shaft, because the tip of the agitator is broken off which would indicate to me that it comes straight up. I tried straps, and a 7 foot 2x4 lever, but it won't budge.
Excellent video very helpful. Great Job
TECHTUBE45 Gkad the video helped you get the washer fixed!
The lid switch is a safety switch and shouldn't be removed. I would replace it and see if that takes care of the problem.
great someone actualy knows what a dog is kinda funny even some of the (mechanics) on you tube seem perplexed by the name. Thanks for a great how too!
+jeff young Glad the video helped you get the agitator fixed!
AppliancePartsPros nj
Look for one with four bolts under the first cap? Any leads
Thank you sir for this very helpful video. Was finally able to fix my grandparents washer. :-D
Awesome, glad you got the washer fixed!
I took the lid switch off a couple months ago it worked fine until 2 weeks ago. Could it be the Agitator?
Former fitness instructor turned Maytag man
Yes, lithium grease will work great!
Thanks for your video, very helpful!
Those boot seals have been discontinued by G.E. but are available aftermarket, here is the part number to enter on our site: AP5183580. As far as getting the agitator off that's another story, they used to make a water bladder that you could put under it to get it off but I don't think you will find one, as these machines haven't been made for about 20 years. I would say let some penetrating oil sink in and try the straps again.
Thank you. Ended up repairing my machine by just replacing the dogs. $6.00 !! :)
Awesome, glad you got the washer fixed!
Thank you for your video it helped me a lot!
Nice job on the video. Thank you.
You are welcome! Glad the video helped you get the washer fixed.
Do these parts also come in a metal alloy? Plastic makes no sense because it strips too easy when washing heavy loads.
At this time the manufacturer only makes them in plastic.
Thank you for the video. It helped alot.
caddys83 Glad the video helped you get the washer fixed!
i have a maytag hav2360aww model how can i move the body to check if the motor is burnt my washing machine stop from working on the last cicle and smell like rubber burning . need some help i don't have a clue if is the motor or the belt any help i will appreciate. thanks
You guys are awesome! Thanks for posting this!
My agitator seems to be stuck. Am I forgetting something??? The bolt has been removed. LOTS of upward force, but nothing.
My washer wont agitate but will spin. I have a maytag centennial commercial technology and I have checked the dogs which are fine, I have checked the motor cuplets and the clutch assembly is just fine I don't know what the problem is. Is there anything you can tell me to check next. Just the machine wont agitate and everything else is fine. I don't spin as fast but it will spin.
I have removed the agitator but can not remove the dust cap or separate the top from the bottom. I have a GE Mod GLWN2800DOW. Any suggestions?
This video is for a Whirlpool style washer. The GE agitators are sold all as one piece. You can go to our web site and enter your model number to see the parts breakdown.
I have the same problem. My dust cap doesn't have a handle to grab and lift. i am sure that if I could get it off , my problem would be solved. I need help! I have a GE model wwse5240g1ww
AppliancePartsPros
Bought the kit but all I needed were the agitator dogs and rubber gasket. everything else was reusable . thank you
Glad you got the agitator working!
Dude! Thanks! 🤘
I can't get my agitator apart every video they pull apart so easy. Any thoughts of what's happening here?
Ryan Marquis They can get stuck together pretty good. As long as it is the type in the video you should be able to pull it apart. There are ones do not come apart so double check!
If I opened the water on it, it would come down from the bottom, so how can I keep it?
The dust cap will not come out. I tried using pliers but fear damaging the cap. How can I get it out without damaging the cap?
+Jack Wagner You can try putting some warm water in there to try and get the gunk to let go. Also try a small screwdriver in between the cap and the side of the upper agitator, to try and break it free.
IF I HAVE A WASHING MACHINE OFF BALANCE WHAT CAN I DO TO FIX IT AND STOP THE THE LOUD NOISE! I WANT TO MAKE MY WASHER QUITE AGAIN!!!! PLEASE ADVISE ME ON WHAT SHOULD I DO!!! PLEASE OR WHERE I COULD GO TO HAVE SOMEONE FIX IT!!
I have tried taking the bolt off the agitator but it will not come off i tried holding do the agitator and still wont un screw.. any idea why?
I can wash a load a clothes it sometimes it will wash, drain and spin with no problem, Then sometimes I'll wash a load it will wash, drain then it won't spin.
What could be causing it?
Thanks..
¡muy bueno! ¡Grasias!
De nada. Me alegro de poder ayudarte.
Thank u
Thanks, SOCOACH50! We've been waiting for someone to call Matt out on it :) You're first!
how do you fix the washer tub if it's not lining up after a move?
On this style of washer you would have to take the cabinet off and inspect the suspension.
needs new counterbalance springs
What if the agitator fell off. Do I fix it the same way?
sugar baby This repair is for the upper agitator. If yours fell off it could just be the bolt came loose. If not check the lower half for any wear or damage especially the splines where it connects to the transmission shaft.
i have an ammana and there no nut,just a spindle,how do i get it out??
babe ruth There are a few designs they have used over the years. You can go to our site and enter your model number to view the parts breakdown. You can also post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem.
Did you find a solution to your problem? Your issue sounds the same as mine. These vids are great but they seem to cover everything except my problem.
my washer doesnt drain the load completely... clothes were still soakin wet but it spins after the rinsing cycle... whats wrong with my washer pls??? HELP!!!
7-16 spin socket you said? My washer has the same problem
It may be a different size depending on your model number. Our videos are just to help give you a general idea on how to do a repair.
@@appliancepartspros hey, your video was so helpful I fixed my washer yesterday
Glad you were able to fix your washer. If there is anything we can help you with in the future please let us know.
@@appliancepartspros I will definitely do
Thanks
Where is Matt? I like him as the pitchman for this channel!
If you go to our website and enter part number AP3094544 you will see that kit and the video on how to change it.
I need to remove agitera out to clean the filter .is a small washer.
Wanda Vazquez You can post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. You can also go to our site and enter your appliances model number to view the parts breakdown, to see how it comes apart.
Okay tx u
do you work on lawn mower s repair clinic does 💓 your hard work too
In fact, we have started selling lawn equipment parts recently! We haven't yet started doing repair videos for them though.
I greased the whole thing. Is that bad?
Ahmad Shanniek You should only have to grease the thrust washer. If you greased the whole thing there is a chance you could get grease on your clothes. A lot of grease may also interfere with the dogs swinging in and out.
After replacing my clutch, I thought I was home free, then the agitator came apart into 15 pieces ... thanks !
how do you ask questions on this site
+Davida Watkins If you need repair help it is best to post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
I cant get the ring to hold the dogs!! Can you help please
joe joe All you should have to do is push it down to snap it into place.
AppliancePartsPros I just found out mine is a 1991 model and doesn't have a collar or ring.. The dogs are just sitting in the gear. Working fine so thank you very, very much.
I replaced the agitator only at the top and it still wont spin what I'm I doing wrong? Does the volt have to be tighten more or should I also do the button
Hey, it's Richard Simmons. What's going on Rich??
😂
My washing machine is extremely slow and usually takes around 1-2 hours just to wash a small load of clothes.
These can kits do not work on my 17 year old Whirlpool washers the only part that I could use was the dogs
Agitator grease is over $30. Why so expensive?
thanks so much for the video , I been trying like hell to find a great video that explains how to do this , my problem though is I need to know the part number I have called everyone including sears and thoe customer care people don't know jack. they doing the same thing I was doing looking on their site and giving me the wrong part number , one guy actually gave me the number for the upper agitator ,when I asked him the number for the kit , I didn't realize his mistake until I looked up the part on there site , just ridiculous. so I wonder can you please help me . I have a Kenmore 800 .. the model number is 110.28847700 . I need to replace the kit , like you just did in the video, and that part looks exactly like the one I took out my machine. I just need to know the correct part number for that kit so I can order and get back to using my machine again . thanks for your help it would really really be appreciated a whole bunch
We're glad to help, Ray! This is the correct agitator kit for your machine: www.appliancepartspros.com/whirlpool-auger-agitator-asm-wp8578210-ap6013533.html
Bring Matt back!
Morning I try to register to put my question in it is hard to register all I need to know is to pull the transmission of the the tub I get the nut loose but transmission would not come loose please help ge stackable washer and dryer model number gtun275em2ww or gtun275em1ww serial number afo10155c I need your help please the washer is leaking badly I try to register it didn't go through thank you in advance
We are limited on what when can do here, we have a limited amount of response space. If you need more in depth help you should register with the repair forum. Here is a picture if a transmission used in those styles of washers, as you listed 3 different model numbers in your 2 questions I do not know if it is the correct one for yours. It looks like it comes as the whole support assembly, it is mounted with a lot of bolts from the bottom. www.appliancepartspros.com/ge-supports-assy-wh16x10186-ap5788202.html www.appliancepartspros.com/motor-drive-assembly-parts-for-ge-gtup270em0ww.html
Yes it has lots of screw
morning I have a new ge stackable washer and dryer my tub a leak I need to no how to pull apart the tub and the transmission thanks in advance model number gtup275emoww
That is way more than we can cover here. I would suggest posting the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
AppliancePartsPros
We the people that
No
Lavadoraautmatic501548 22kilos heñ
+Erick Mullen I do not know what this means but I hope the video helped you fix your washer!