For the flush cut trick, not every workshop will have veneer on hand, but everyone will have sandpaper. Using it backing side up should work perfectly.
Hi Colin, just small OT geo-political note, hope you don't mind. Your Narex chisels are probably still Made in Czechoslovakia but we've been split almost 20 years ago (political decision) ;-) But it's true that Czechoslovakia is still the "known brand" in US/Canada, esp. because of the ice hockey. While with Czechia and Slovakia, lots of people in US just "know" it's where the wars were (Chechnya and Slovenia). End of OT Thanks for your videos and have a nice weekend.
4:40 there not good chisels if you jab at them that means there dull or your just not useing them right ur suppose to use them like a saw kind of like a sliceing action not jabbing
We used very similar tape when I was in the Air Force back in the 1970's. It was orange, usually with a different color stripe in it. I still have some, and it works perfectly.
Tape to mark centres, to prevent marking the wood? Why would you bother about making marks on waste wood, that will be removed with the drill? Sorry about the crit's but I have one other. When flushing up proud dowels, I was taught to not to use the chisel like a hammer but more like a knife. Lay the chisel flat on the surface, slide the edge up to the dowel and move it slightly from side to side. It makes a cleaner cut without bruising the end grain.
Exactly, as a chippie for over 50 years I know a little and you do not do as vid, "instead pare the end grain" (left hand on flat of chisel and with right hand, kind of of stroke across right to left. Your Vid's are excellent Colin, BUT with end grain it is treated differently and a super sharp is a must to work end grain
That Silicone wrap is very similar to stuff we used in the Navy to wrap electrical harness, and wire braided cable. It came in black or red for high temp areas.
I love the tips. Learned a lot from your channel. However, when you were showing how to square a hole in a pipe etc. I could t help but think that it would be just as accurate to mark it with a speed square. Food for thought?
Curious about what yous said regarding the veneer having so many uses. Have you done or would it be worth doing a video that demo's various ways you use it around the shop? Thanks.
There are about 30 reasons to have a deck if cards in your shop. This trick. Leveling. Centering. Facing to stop impressions in softer wood. And many more! Look it up. I have 3-4 decks in mine. Usually use them at least 5-6x a week.
Great stuff, Colin. I would add that in a pinch, use a drywall screw for a center punch/ awl (wood drilling). The points are very sharp and the steel fairly stout. I have even used them for marking holes in aluminum.
Tip 1: Question: If the adventure tape sticks to itself, then why does it need to be wrapped on the ends? Logic says that if the sticking power isn't enough to hold itself together under tension, then it's not tape and simply a self-sticking rubber length (because rubber sticks to itself anyway until it's coated). Tip 2. Veneer is expensive. What I us?. Painter's tape. Cheaper, readily available, and adjustable to curved surfaces unlike veneer. Also, chiseling that dowel flat is a wasted step since you'll likely have to sand the whole thing anyway. Just sand it flat. Tip 3. Why have two different kinds of tape in your shop when you can use painter's tape for just about everything from clamping, to preventing tear-out, to holding multiple pieces together to cut them at the same size, to masking off finish when you have to pre-finish before gluing, for marking ... one tip ... Painter's tape. Yes, masking tape will work, but when it's on too long it leaves glue and bits behind that have to be sanded off. Painter's tape doesn't. At least, not in my experience. Tip 4. Turning a snapped screwdriver into an awl is a brilliant idea! Yeah, you can get them very, very cheap at garage sales or someplace like ReStore, which are stores set up by Habitat for Humanity. Or better yet, we all have a driver that's been stripped beyond being useful. Now, it can be useful with a little grinding. Brad point bits are awesome. Tip 5. Again, brilliant. I'd never have thought of that. Or I would have eventually after many, many mistakes. Great tip. I love your tips segments. I know it seems like I'm questioning a lot of things, but they're things to think about before spending a lot of money on something that's not going to work like you expect, or when there's a cheaper/easier option available. Glad you're here posting!
An old deck of cards has a lot of uses in the shop as adjustable shims. But for a spacer to cut against you can always use a piece of postcard-like material that you get in the mail as junk mail, or another thing I do is save old packaging when I buy a product that comes with cardboard on the back and clear plastic on the front. I cut out the flat part of the plastic and save it in my toolbox for future use. I really like using the tape to mark on things. When hanging pictures I use the wide blue tape and put pieces on the wall to mark on. Then I drive nails or picture hangers through the tape and then peel the tape off. A sharpened screwdriver? Lots of us have broken screwdrivers but even easier you can sharpen a big nail, or random piece of steel rod. Throw it in a corner of your toolbox so you know where it is when you need it. If you do metal work it is better to buy a proper hardened steel centerpunch so you can use it on metal, it will work real well on wood. For many years I've used normal metal working drill bits but recently I splurged on a good set of brad point bits because they work so much better for woodworking.
Or you could use a dowel saw , they allow you to cut a dowel off flush because the teeth are only raised on one side so you don’t mark or scuff the wood you are cutting against.
Question: Why don't folks typically glue the entire end of a board when doing dowel joints? I've seen quite a few videos of dowel use and normally only see them glue the dowel holes/dowel. Or am I just seeing a small percentage of folks who only do that?
Have you ever read instructions on how to properly tighten the drill bit? They state that tightening down on all three of the key locks will properly tighten and keep a drill bit in place. Almost no one does this and then they wonder why the drill bit may come loose.
If the tape is what I think it is, it's butyl rubber, was indespensible in both the electrical and plumbing industries to bind, insulator and waterproof cables and joins.
For the flush cut trick, not every workshop will have veneer on hand, but everyone will have sandpaper. Using it backing side up should work perfectly.
Read my mind
Colin your common sense approach is nicely delivered. Thanks
Hi Colin, just small OT geo-political note, hope you don't mind.
Your Narex chisels are probably still Made in Czechoslovakia but we've been split almost 20 years ago (political decision) ;-)
But it's true that Czechoslovakia is still the "known brand" in US/Canada, esp. because of the ice hockey. While with Czechia and Slovakia, lots of people in US just "know" it's where the wars were (Chechnya and Slovenia).
End of OT
Thanks for your videos and have a nice weekend.
narex today is a profitable part of festool family
I just wanted to write a similar comment, but luckily I noticed yours .
what was that link to those chisels? thanks
Colin yet another good\sensed informational video.
All your videos are interesting to watch it doesn't matter whatever you share I benefit from it just to let you know
4:40 there not good chisels if you jab at them that means there dull or your just not useing them right ur suppose to use them like a saw kind of like a sliceing action not jabbing
We used very similar tape when I was in the Air Force back in the 1970's. It was orange, usually with a different color stripe in it. I still have some, and it works perfectly.
Still used. The one I used was black with a green stripe. F4 tape
Tape to mark centres, to prevent marking the wood?
Why would you bother about making marks on waste wood, that will be removed with the drill?
Sorry about the crit's but I have one other. When flushing up proud dowels, I was taught to not to use the chisel like a hammer but more like a knife. Lay the chisel flat on the surface, slide the edge up to the dowel and move it slightly from side to side. It makes a cleaner cut without bruising the end grain.
Exactly, as a chippie for over 50 years I know a little and you do not do as vid, "instead pare the end grain" (left hand on flat of chisel and with right hand, kind of of stroke across right to left.
Your Vid's are excellent Colin, BUT with end grain it is treated differently and a super sharp is a must to work end grain
Variation on veneer shim for cutting the dowel.. would a dowel-sized notch in the veneer be useful?
That Silicone wrap is very similar to stuff we used in the Navy to wrap electrical harness, and wire braided cable. It came in black or red for high temp areas.
Thank you for your service!
I have not seen the pull saw card trick. I will use it.
Awesome tips, Colin! Thanks! 😃
Stay safe there with your family! 🖖😊
I love the tips. Learned a lot from your channel. However, when you were showing how to square a hole in a pipe etc. I could t help but think that it would be just as accurate to mark it with a speed square. Food for thought?
Curious about what yous said regarding the veneer having so many uses. Have you done or would it be worth doing a video that demo's various ways you use it around the shop? Thanks.
As usual, great tips & tricks Colin! Happy Holidays to you & your family! 👍👍
What is a good chisel? As you clearly demonstrated, a sharp one!
Great tips. Thanks for sharing. But I can't find the link to the to itself sticking tape. 😞
There are about 30 reasons to have a deck if cards in your shop. This trick. Leveling. Centering. Facing to stop impressions in softer wood. And many more! Look it up. I have 3-4 decks in mine. Usually use them at least 5-6x a week.
Great pipe drilling tip. That would never have occurred 2 me.
I put a 1/4" Hex Shank Keyless Drill Chuck Adapter in my drill press. For light duty drilling, it really speeds up bit changes.
Great video. I have a wood watch like yours. I really like it. I use the tape trick all the time. 👍❤..
Silicone wrap is the same as Adventure Tape, you can find it in the electrical section of any big box store, probably a smaller hardware store too.
Plumbing section as well, since you can use it for low pressure repairs.
Great stuff, Colin. I would add that in a pinch, use a drywall screw for a center punch/ awl (wood drilling). The points are very sharp and the steel fairly stout. I have even used them for marking holes in aluminum.
"When you find y-awl-selves in a punch pinch"
Good job 👏 Thanks
Czechoslovakia fell apart some 40 years ago lol, I can't remember the last time I heard someone mentioned it
On January 1st, 2023 it will be exactly 30 years.
I bought a few of the Dollar Tree screwdriver sets. When they break on me I turn them into awls.
Great tips thanks for sharing
Tip 1: Question: If the adventure tape sticks to itself, then why does it need to be wrapped on the ends? Logic says that if the sticking power isn't enough to hold itself together under tension, then it's not tape and simply a self-sticking rubber length (because rubber sticks to itself anyway until it's coated).
Tip 2. Veneer is expensive. What I us?. Painter's tape. Cheaper, readily available, and adjustable to curved surfaces unlike veneer. Also, chiseling that dowel flat is a wasted step since you'll likely have to sand the whole thing anyway. Just sand it flat.
Tip 3. Why have two different kinds of tape in your shop when you can use painter's tape for just about everything from clamping, to preventing tear-out, to holding multiple pieces together to cut them at the same size, to masking off finish when you have to pre-finish before gluing, for marking ... one tip ... Painter's tape. Yes, masking tape will work, but when it's on too long it leaves glue and bits behind that have to be sanded off. Painter's tape doesn't. At least, not in my experience.
Tip 4. Turning a snapped screwdriver into an awl is a brilliant idea! Yeah, you can get them very, very cheap at garage sales or someplace like ReStore, which are stores set up by Habitat for Humanity. Or better yet, we all have a driver that's been stripped beyond being useful. Now, it can be useful with a little grinding. Brad point bits are awesome.
Tip 5. Again, brilliant. I'd never have thought of that. Or I would have eventually after many, many mistakes. Great tip.
I love your tips segments. I know it seems like I'm questioning a lot of things, but they're things to think about before spending a lot of money on something that's not going to work like you expect, or when there's a cheaper/easier option available.
Glad you're here posting!
An old deck of cards has a lot of uses in the shop as adjustable shims. But for a spacer to cut against you can always use a piece of postcard-like material that you get in the mail as junk mail, or another thing I do is save old packaging when I buy a product that comes with cardboard on the back and clear plastic on the front. I cut out the flat part of the plastic and save it in my toolbox for future use.
I really like using the tape to mark on things. When hanging pictures I use the wide blue tape and put pieces on the wall to mark on. Then I drive nails or picture hangers through the tape and then peel the tape off.
A sharpened screwdriver? Lots of us have broken screwdrivers but even easier you can sharpen a big nail, or random piece of steel rod. Throw it in a corner of your toolbox so you know where it is when you need it. If you do metal work it is better to buy a proper hardened steel centerpunch so you can use it on metal, it will work real well on wood. For many years I've used normal metal working drill bits but recently I splurged on a good set of brad point bits because they work so much better for woodworking.
Or you could use a dowel saw , they allow you to cut a dowel off flush because the teeth are only raised on one side so you don’t mark or scuff the wood you are cutting against.
hey Colin, is screwdriver steel actually hard enough for an awl you find? now I'm thinking about hacking a broken screwdriver into a Birdcage awl
Also known as "rescue tape" -- available in a lot of hardware stores for about $10/roll. Never thought of using it for this purpose!
i m a pakistani but i love yours detailed videos
Bicycle tube could do the same as jour tape
I thought you were laying a sheet of sand paper face down instead of veneer. I guess there’s lots of things you could use
The sandpaper would work too.
Also known as friction tape. Used it when I was in the Air Force.
Question: Why don't folks typically glue the entire end of a board when doing dowel joints? I've seen quite a few videos of dowel use and normally only see them glue the dowel holes/dowel. Or am I just seeing a small percentage of folks who only do that?
For soft wood like pine if you want a threaded hole, I just drill undersized and force the screw in there, it makes it's own threads no problem
That tape looks useful, but you can do similar things with an old bike tube. Cut it to any width and length you need.
That tape has been used in auto industry for a while. Great for emergency repairs for hoses and even gas lines for temporary fix
Have you ever read instructions on how to properly tighten the drill bit? They state that tightening down on all three of the key locks will properly tighten and keep a drill bit in place. Almost no one does this and then they wonder why the drill bit may come loose.
Im pushing 80 and sometimes i.wish i.was younger because of these types of.videos
But.then i look at.the young CULTURE...they are so so lost.
That tape is called self amalgamating tape. Has many uses.
If the tape is what I think it is, it's butyl rubber, was indespensible in both the electrical and plumbing industries to bind, insulator and waterproof cables and joins.
This looks like what we call F4 tape. It was used in the Air Force.
Hate to be pedantic, but Czechoslovakia hasn't existed in over 75 years. Narex are made in the Czech Republic.
Thats self amalgamating tap
Yep, mainly used for sealing satellite connections to dish (wonderful stuff)
Sad, sad situation....why use the fence if you are not going to use it correctly?
Jill, John, Micheal and Suzy went to a store one day…..
Czech Republic, there is no Czechoslavkia
pls use proper terms when teaching - it was "Czechoslovakia" then, now the Czech Republic and Slovakia, both EU countries
Chisels are not very sharp!
🥸🥸🥸🥸🥸😭😭😭😭😭😭
That tape looks awful