I had a great time watching at your. Video. A great help. Now if you can do a video on Wd90j6410as, on how to repair it's motherboard. It would really help. Thanks bro
I get the same error on my machine and I haven't seen anyone who takes a good video like you. My motor is turning. There is no problem in SP test mode either, but it stays somewhere while the program is running. I removed the motor and cleaned the area where the motor and the coal are, and since its efficiency is low, the tacho meter may act as if its efficiency and performance have decreased in the measurement.
Hello brother Sorry to hear that you are facing issues with your washing machine. But if your machine stops randomly during washing cycles, then its almost always the relays. Check for cracked solder joints underneath the relays. I wish you all the best brother
@@FixTronics Thank you for your knowledge. Yes, I did not remove the place where the relays are, but since I thought there was a contact problem, I tightened the relays that made them upside down without removing them and your solution worked. Thank you. The charity of intelligence is knowledge. Thank you for sharing.
@@ismail_aydemir_youtube Glad to hear you fixed it. Thank you so much brother for being here in my channel. I really appreciate it. I wish you all pleasant life to you and your family
Thank you so much brother I really appreciate your support The UC code turned out to be due to a high voltage at my house, its 250v where it should be 220 to 240v. Whan I used the variac at the end of the video and reduced the voltage to 230v, the code disappeared.
@@FixTronics Thank you, brother. I always enjoy your explanations. Can I request a favor? I have read a lot about op-amps but I still don't fully understand their uses and types. Could you please make a video explaining it with simple examples?
![Как создаются Микрочипы? Этапы производства процессоров [Branch Education на русском]](/img/n.gif)
I had a great time watching at your. Video. A great help. Now if you can do a video on Wd90j6410as, on how to repair it's motherboard. It would really help. Thanks bro
You welcome brother
I get the same error on my machine and I haven't seen anyone who takes a good video like you. My motor is turning. There is no problem in SP test mode either, but it stays somewhere while the program is running. I removed the motor and cleaned the area where the motor and the coal are, and since its efficiency is low, the tacho meter may act as if its efficiency and performance have decreased in the measurement.
Hello brother
Sorry to hear that you are facing issues with your washing machine.
But if your machine stops randomly during washing cycles, then its almost always the relays.
Check for cracked solder joints underneath the relays.
I wish you all the best brother
The machine is already working in the spin but I am thinking of checking the relay and triac system. Thank you
All the best brother
@@FixTronics Thank you for your knowledge. Yes, I did not remove the place where the relays are, but since I thought there was a contact problem, I tightened the relays that made them upside down without removing them and your solution worked. Thank you. The charity of intelligence is knowledge. Thank you for sharing.
@@ismail_aydemir_youtube Glad to hear you fixed it.
Thank you so much brother for being here in my channel.
I really appreciate it.
I wish you all pleasant life to you and your family
Amazing bro! I watched the video till the end. The first error code "uc" appears because of a voltage detector transistor or some other issue.?
Thank you so much brother
I really appreciate your support
The UC code turned out to be due to a high voltage at my house, its 250v where it should be 220 to 240v.
Whan I used the variac at the end of the video and reduced the voltage to 230v, the code disappeared.
@@FixTronics Thank you, brother. I always enjoy your explanations. Can I request a favor? I have read a lot about op-amps but I still don't fully understand their uses and types. Could you please make a video explaining it with simple examples?
Thank you a lot brother, because a have the same problems error code Uc and C3 and now I can solve my mistakes 😊😊😊