LED bulb repair (DIY)

Don't throw away your old led yet it can be fixed. The leds are in series so if there is just one light that is broken the whole like will not turn on. What a waste just put a 600ohm resistor where the blown led is will fix the light.
I found a faster way to repair a broken led bulb, just solder over the broken led no need for the resistor.
Resistors (amzn.to/3ozLLkA)
Soldering iron (amzn.to/3j3Lkhw)
Led tester (amzn.to/3pz6ZR9)
#LEDbulbRepair
#NewsonsElectronics
#SaveMoney
tags
led bulb repair,fix led light,led light not working,how to repair an led light,simple led repair,how to repair led,how to repair led bulb,how to repair led light,how to repair energy saver bulb,led lamp,led bulb,repair energy saver bulb,repair energy saving light bulb,repair energy saver,newsons electronics,REPAIR YOUR OWN LED BULB,LED,DAMAGE LED BULB,LED BULB EASILT REPAIR

[@StrPtrn]

Good fix...!

[@georgeosborn3553]

Glad i watched , mine was flickering so i took it apart with a razor knife ( for a cleaner put together) and the bad led just plucked away with no problem , i used a soldering iron and put just a little solder onto make the connection , re-installed bulb to make sure it was repaired ( it was ) then took and superglued the plastic globe back on 👍

[@floogelhornzzz4770]

It snaps back on easy if you didn't damage it taking it off. You don't need glue.

[@georgeosborn3553]

@@floogelhornzzz4770 i damaged mine so yeah , had to reglue it 😔

[@ElectronicaVK]

You can make the led lamps immortal by making minor changes in the circuit immediately after purchasing them. I use this method, my lamps never explode. You can watch.

[@jaimeim18]

Why new leds are hard to find?

[@kabandajamir9844]

So nice thanks sir

[@Golliyo]

nice, thanks

[@pedroscruiser]

This is so Canadian.

[@floogelhornzzz4770]

Where on earth are people supposed to get resistors of a certain Ohms, or whatever? Most people do not understand electronics or the specifications of components or where to get them. And they wouldn't go to all the trouble and expense of getting all these things. They would just buy a new bulb. Other videos just say to scotch tape a piece of tin foil in its place.

[@Mrbobinge]

Without soldering-iron, just short-circuit each dud led with a Circlip (c-clip). Amazon $10 for box of assorted 400 clips. Mini C-clip pliers $10.
Why bother to solder bridging resistors? Onboard electronic chip, limits the current.

[@NewsonsElectronics]

good idea

[@mrbill6666]

Why even put the cover back on? it’s just going to hold the heat and make the remaining bulbs burn out quicker while absorbing some of the light, no?

[@floogelhornzzz4770]

Correct. Another instruction video said the exact same thing.

[@turkishwithemre]

What happens without Resistor if i use ?

[@NewsonsElectronics]

yah you don't need a resistor the light will be brighter but it will not last as long because the leds have more current through them so a simple fix is just short out the bad leds it work fine.

[@turkishwithemre]

@@NewsonsElectronics thank you for the answer.. my last question . how do you calculate the resistor to add there ?

[@NewsonsElectronics]

@@turkishwithemre Volts/Current = resistance
I think each led was 6V and 30ma should be fine to determine the value

[@ariewijaya1679]

Why not using solder for removing the bad led

[@MrNew-us1lg]

the leds would be hard to remove with solder you would need a heat gun as the are surface mount

[@kabandajamir9844]

So n

[@ashleykimlee460]

Buying a new one is much cheaper than repair and save a lot of time.

[@NewsonsElectronics]

that is not the point

[@floogelhornzzz4770]

How much is a new one? And people waste tons of time in their lives watching TV or playing video games or yakking on the phone or watching tiktok videos or taking selfies or sitting around drinking anyway. Might as well do something you feel proud of accomplishing.