I had an issue on my 2010 Compass (same platform) where it wouldn't start, but then when it, the red lightning bolt came on. It wasn't the throttle body, instead being caused by corrosion in the relay box, located in the driver fender, and then the car worked normally after rewiring that.
My sister inlaws car is a 2012 jeep patriot. Itd have trouble getting up to speed and didnt feel like itd wabt to shift so obviously limp mode well two shops recommended a trans swap so we did and now the car went into limp mode again except this time it can go 65mph and you can press on the gas and speed will stay and rpms will rise or you can drive totally like normal. Is just super intermittent wether its limp mode or not. The check engine light is on. The furst shop claimed they replaced the throttle body before diagnosing it as the transmission. Thabk you for the tip on the codes i will try that tomorrow. And ideas on what it could be?
Hi Sam. It's Mrs Wrenching. Post your issue on the Facebook page Wrenching with Kenny & Backyard Mechanics (be sure to answer all the questions for Backyard Mechanics). Your post has to include any codes the vehicle has & what driveability issues you're having. Thanks for watching! Meg
Mine also had a bad throttle body. I did the relearn and it would fix it temporarily. It made it to 180k and now has the code p0777 p0730. It revs but doesn't move much and then the throttle goes unresponsive completely (assuming some kind of limp mode). I finally threw a throttle body in it hoping it would fix it but no luck.
The counter in the ECU needs to be reset to get it out of limp mode. Either the fluid got lowand burnt, Or a sensor failed And cause the ECU to put the Jeep in limp mode. Only a Chrysler code reader can reset the ECU properly.
The jeep 4 cylinders line up engines are European, German I think. My 2014 conpass was 120k and I had to swap my throttle body. It would switch to low power for a mass air vacuum leak and some other code. Haven't had an issue since. Took about a 6 pack and I was done and back on the road. Throttle no longer runs off a cable so the chip set was going out so mine wouldn't close, jeep felt like the transmission was slipping or hard shifting too. Sometimes it would accelerate hard on its own.
Love jeeps hate everything else from them. Great video but you should include the fix if not the last result or have a commentary in the end explaining exactly what fixed it
Just thinking you're well spoken easy to understand & just need to do complete video's. Keep up the good work & consider what I said. Some ppl click & skip to the end. You'll widen your audience getting more views
I just did the same thing and it didn't work at all maybe it's pending but I have 4x4 light Trac control and abs light come on and then I can only drive 10 mph for like a couple minutes but she'll kick out of that and go back to normal after
I'm getting P097E Shift Solenoid E Control Circuit/Open on my 2016 - I tried the key trick and it never gave me any codes. I had to buy a code reader to pull it. The dashboard would just tell me ------ and then done. I replaced the throttle body this week thinking that's what it might have been since I'm at 76k, sadly, that wasn't it :(
my 2010 compass have a tranny code p167a, but it will not clear the code because for some reason my scanner reads rpm at 3488 but engine is off? since the conditions are not met (the scanner thinks engine is running but is not). what can cause the scanner to read 3488 rpm when engine is off?
my 2011 jeep compass has the low tire pressure sign that goes on and off, then the check engine light goes on and off randomly then tonight it went into limp mode with traction control off light on and was accelerating slowly like super slowly i pulled over turned it off started back up it went off and then came back on and went back into limp mode, any ideas?
There's many reasons it could be a repeat repair . First , why was it replaced a few months ago? What were the codes? What's it doing now? What are the codes now? Limp mode, where the throttle body won't work, doesn't necessarily mean the throttle body is no good. It could be a pedal issue, a wiring issue, transmission issue, ABS issue, engine issue. It has to be diagnosed to figure out what's going on
@@WrenchingWithKenny the little lightning bolt came up on the dashboard I took it to the mechanic shop and I said yeah you have a bad throttle body they replaced it it worked fine then it just started acting up again every morning before I start it it makes a loud noise like like air coming out after I start it then the idle is kind of shaky when it's warming up it looks like he wants to die I've had the vehicle for 10 years I've never changed the spark plugs and never had a tune-up I'm thinking about doing that next when I got it I only had 80,000 miles now I have 190,000 it's a 2010 Patriot my airbag light has been on for like 6 months I took it to Jeep they said there was a recall on the sensor for the airbag they replaced it but they couldn't get the light off the dashboard and I always have a low tire sensor seems like it's common for these Jeeps to have the same issues I'm thinking about selling it I have an offer for $2,000
@@louismfrancojr2462 just got this December and it's like this too.I die out on the road to the next residential place.Not even paid off yet and giving me problems.
Everyone knocks the cvt trannies my 2012 Jeep Patriot has 341k miles on it and the only major issue I've had is it overheated and blew a head gasket about 240k because one of the thermostats failed.
You cannot read the codes after the Jeep is in limp mode. ECU is causing all these faults. The original code before it went into lip mode. Like speed sensor. Oxygen sensor. Low tranny fluid. Needs oil changed. These are what caused the ECU to go into length mode. Is counter in the ECU must be reset. Then you can fix the problem. I bet money it's as simple as a wheel speed sensor. But there ain't a mechanic out there that's gonna say that they're all gonna say your transmission is shot.
I got a 2015 compass, lightning bolt is on and flashing. I cleaned the throttle body, my battery works, my oil is fine, but the car is stuck in limp mode, engine light is on and the codes I have are U1424, U1407 and P161B (i think). I’m just so confused and annoyed with it, I’m not sure if it’s the throttle body or the transmission control module.
@@queertube8153Thanks man, it was the throttle body. I spent about $75 on the part searched up how to do it online and fixed it. Definitely better than spending $550 to get the car checked out and fixed.
That does not have a CVT in it. It has a ZF9 speed transmission in it not a CVT. Definitely not a Nissan transmission Nissan don’t make transmissions. Come on now.
My dodge went into limp mode then wouldn't start again, no compression in 4 cylinders can limp mode cause that i know it can mess with timing ? Pkease help😮
You probably have the multiair engine. If it's not started for a while, you'll lose oil pressure on the valve tappets and it won't start. Just keep cranking it for what seems like a dick-year and it'll regain pressure and fire.
It wasn't a jeep, but that happened to my 05 Vibe. 5 speed manual, wouldn't go over 2500 or so in any gear, couldn't go over 40mph. It was the throttle body position sensor. Replaced the throttle body. $50 and a couple of bolts. I imagine if that sensor goes out the vehicle goes into limp mode.
I had an issue on my 2010 Compass (same platform) where it wouldn't start, but then when it, the red lightning bolt came on. It wasn't the throttle body, instead being caused by corrosion in the relay box, located in the driver fender, and then the car worked normally after rewiring that.
My sister inlaws car is a 2012 jeep patriot. Itd have trouble getting up to speed and didnt feel like itd wabt to shift so obviously limp mode well two shops recommended a trans swap so we did and now the car went into limp mode again except this time it can go 65mph and you can press on the gas and speed will stay and rpms will rise or you can drive totally like normal. Is just super intermittent wether its limp mode or not. The check engine light is on. The furst shop claimed they replaced the throttle body before diagnosing it as the transmission. Thabk you for the tip on the codes i will try that tomorrow. And ideas on what it could be?
Hi Sam. It's Mrs Wrenching. Post your issue on the Facebook page Wrenching with Kenny & Backyard Mechanics (be sure to answer all the questions for Backyard Mechanics). Your post has to include any codes the vehicle has & what driveability issues you're having. Thanks for watching! Meg
Great tip to get codes is awesome
Same thing happened to my wifes compass and the map sensor went out. $30 dollar part and five minutes to swap
Mine also had a bad throttle body. I did the relearn and it would fix it temporarily. It made it to 180k and now has the code p0777 p0730. It revs but doesn't move much and then the throttle goes unresponsive completely (assuming some kind of limp mode). I finally threw a throttle body in it hoping it would fix it but no luck.
The counter in the ECU needs to be reset to get it out of limp mode. Either the fluid got lowand burnt, Or a sensor failed And cause the ECU to put the Jeep in limp mode. Only a Chrysler code reader can reset the ECU properly.
The jeep 4 cylinders line up engines are European, German I think. My 2014 conpass was 120k and I had to swap my throttle body. It would switch to low power for a mass air vacuum leak and some other code. Haven't had an issue since. Took about a 6 pack and I was done and back on the road. Throttle no longer runs off a cable so the chip set was going out so mine wouldn't close, jeep felt like the transmission was slipping or hard shifting too. Sometimes it would accelerate hard on its own.
Love jeeps hate everything else from them. Great video but you should include the fix if not the last result or have a commentary in the end explaining exactly what fixed it
Just thinking you're well spoken easy to understand & just need to do complete video's. Keep up the good work & consider what I said. Some ppl click & skip to the end. You'll widen your audience getting more views
Believe it or not the brake switch and sensor since it's a JATCO CVT ...
English? Do you speak it?
@@w.e.s. Perfectly. I also speak French!
My 2015 patriot has 250k on it still going strong
Oh it will! Just wait!
CVT or the six speed ? Have you changed the trans oil?
@@gdelfinowhat does changing Trans fluid do?
My friend has a 2014 Patriot and it's been nothing but problems! She called me this morning, needing a ride to work. It wouldn't shift into reverse.
Tell her to park accordingly
I just did the same thing and it didn't work at all maybe it's pending but I have 4x4 light Trac control and abs light come on and then I can only drive 10 mph for like a couple minutes but she'll kick out of that and go back to normal after
Abs sensor
Ever figure out this issue? I’m dealing with it now
For those lights I change the abs sensors and it was fixed. On mine the sensors were faulty
Hey Kenny I just bought one of these bad boys is there any way to make that transmission last any longer
I'm getting P097E Shift Solenoid E Control Circuit/Open on my 2016 - I tried the key trick and it never gave me any codes. I had to buy a code reader to pull it. The dashboard would just tell me ------ and then done. I replaced the throttle body this week thinking that's what it might have been since I'm at 76k, sadly, that wasn't it :(
Check that sensor before you fight with the throttle body.
Please what sensor are you talking about. my jeep has unresponsive throttle when the engine is hot
my 2010 compass have a tranny code p167a, but it will not clear the code because for some reason my scanner reads rpm at 3488 but engine is off? since the conditions are not met (the scanner thinks engine is running but is not). what can cause the scanner to read 3488 rpm when engine is off?
my 2011 jeep compass has the low tire pressure sign that goes on and off, then the check engine light goes on and off randomly then tonight it went into limp mode with traction control off light on and was accelerating slowly like super slowly i pulled over turned it off started back up it went off and then came back on and went back into limp mode, any ideas?
Bad grounds
I have a 2007 jeep compass doing the same
My 2015 compass is doing the exact same
Were any of you guys able to fix it?
2018 compass same thing any luck?
My 2012 patriot has 160,000 miles on the original cvt and runs strong
2 months later and now it’s whining lol.. I guess I’m doing the filters and fluid change!
@@MoloneLabe Good luck! my CVT on my 2011 Patriot just went out at 192K miles
@@VehVeloMedia the fluid and filters fixed my issue!
@@MoloneLabe Nice. Hopefully it fix mines
@@VehVeloMedia is yours whining and feeling sluggish? That’s what mine was like and now she feels alive!
I had my throttle body changed and a few months later the issues came back? Why
There's many reasons it could be a repeat repair . First , why was it replaced a few months ago? What were the codes? What's it doing now? What are the codes now?
Limp mode, where the throttle body won't work, doesn't necessarily mean the throttle body is no good.
It could be a pedal issue, a wiring issue, transmission issue, ABS issue, engine issue. It has to be diagnosed to figure out what's going on
@@WrenchingWithKenny the little lightning bolt came up on the dashboard I took it to the mechanic shop and I said yeah you have a bad throttle body they replaced it it worked fine then it just started acting up again every morning before I start it it makes a loud noise like like air coming out after I start it then the idle is kind of shaky when it's warming up it looks like he wants to die I've had the vehicle for 10 years I've never changed the spark plugs and never had a tune-up I'm thinking about doing that next when I got it I only had 80,000 miles now I have 190,000 it's a 2010 Patriot my airbag light has been on for like 6 months I took it to Jeep they said there was a recall on the sensor for the airbag they replaced it but they couldn't get the light off the dashboard and I always have a low tire sensor seems like it's common for these Jeeps to have the same issues I'm thinking about selling it I have an offer for $2,000
@@louismfrancojr2462 with that kind of mileage, $2K is not a bad offer
@@louismfrancojr2462 just got this December and it's like this too.I die out on the road to the next residential place.Not even paid off yet and giving me problems.
@@Redmeatsteak I changed my Spark plugs and went away runs good now try that...
Was it fixed after replacing the throttle body?
It was my intake manifold gasket failure after I changed throttle body same code
Everyone knocks the cvt trannies my 2012 Jeep Patriot has 341k miles on it and the only major issue I've had is it overheated and blew a head gasket about 240k because one of the thermostats failed.
@Brad.W That's great news. Thanks for sharing. Keep wrenching! Kenny
Jeep Compass and Jeep Patriot are known for bad grounds. I believe these vehicles were built by Fiat
Benz not fiat, maybe not these.
F.I.A.T = Fix It Again Tony
You cannot read the codes after the Jeep is in limp mode. ECU is causing all these faults. The original code before it went into lip mode. Like speed sensor. Oxygen sensor. Low tranny fluid. Needs oil changed. These are what caused the ECU to go into length mode. Is counter in the ECU must be reset. Then you can fix the problem. I bet money it's as simple as a wheel speed sensor. But there ain't a mechanic out there that's gonna say that they're all gonna say your transmission is shot.
I got a 2015 compass, lightning bolt is on and flashing. I cleaned the throttle body, my battery works, my oil is fine, but the car is stuck in limp mode, engine light is on and the codes I have are U1424, U1407 and P161B (i think). I’m just so confused and annoyed with it, I’m not sure if it’s the throttle body or the transmission control module.
I had the same. I just ordered a throttle body from amazon and replaced myself and it solved the problem.
@@queertube8153 I’m about to try that myself to see if it’s the throttle body
@@queertube8153Thanks man, it was the throttle body. I spent about $75 on the part searched up how to do it online and fixed it. Definitely better than spending $550 to get the car checked out and fixed.
That does not have a CVT in it. It has a ZF9 speed transmission in it not a CVT. Definitely not a Nissan transmission Nissan don’t make transmissions. Come on now.
My 2008 jeep liberty suddenly lost speed and couldn't accelerate i had to pull over and the car off and turn it again to get normal speed again
Sounds like it went into a limp mode for some reason
Spark plugs?
Mine did the same thing had to turn it off then wait and turn it back on and works fine
Mine does the same thing but throws a small evap leak code every once in a blue … yesterday I tried the restart and it wouldn’t start back up😢
U ever find out why? My liberty did the same.
My dodge went into limp mode then wouldn't start again, no compression in 4 cylinders can limp mode cause that i know it can mess with timing ? Pkease help😮
You probably have the multiair engine. If it's not started for a while, you'll lose oil pressure on the valve tappets and it won't start. Just keep cranking it for what seems like a dick-year and it'll regain pressure and fire.
I have my 2014 compass having forced maximum 2 rpm issue.. how can i fix it?
It wasn't a jeep, but that happened to my 05 Vibe. 5 speed manual, wouldn't go over 2500 or so in any gear, couldn't go over 40mph. It was the throttle body position sensor. Replaced the throttle body. $50 and a couple of bolts. I imagine if that sensor goes out the vehicle goes into limp mode.
@@tekwerk Thanka Mate…
Speed limit 11 to 15 miles an hour
Electronic throttle control is bad. Replace the throttle body and the car will drive better than ever
Bad REPS, not Raps. Reps is short for reputation
1 year later first time seeing March 8 2023
1:45
Tell me the problem not your life story
How rude
What was the problem
Hahaha!
Lol😂
Your the problem .
You don't MAKE ANY SENCE
Chrysler makes trash. Imagine endorsing Chrysler products but saying you don't like the only half way decent thing they've made in decades.