I followed all your Voron videos, I must say these where more helpful than any other video on TH-cam, thank you very much, we need follow up videos on what you have been doing lately
Just finished my first 2.4 build, and I have to say this series of build videos is the best I have found, including build videos from well known Voron team members. Saved me a lot of time and grief in places where the printed manual was less clear. I also like that it is divided into manageable chapters, so it is easier to find what you are looking for without jumping around in a 6 hour marathon video. Thanks alot!
I don't comment on youtube videos all that often, but I really wanted to say thank you for this amazing resource. As my first time working with Klipper this made the process SO much easier.
Thank you so much for your wonderful series of videos on building a Voron 2.4. I finished building min last April and found your guides an invaluable resource. Keep up the good work!
your videos are so well made that even if i don't own a voron (yet) i'll still watch the entire build process to prepare myself for my future build. thank you for this great content, you should reach out to the voron guys and make this series a true build guide instead of the pdf manual!!! congrats man
Best series out there!! Thanks for all your work. My Voron 2.4r2 kit will be here in a week or so and I already have everything ready for Stealthburner except for your video! Let's go! 😀
Love your tutorials. They are the best videos on how to build a voron on TH-cam. No one comes close tbh. Because of you I've self sourced a V2.4 R2. Watching your videos almost daily for the past 6 months. One question though which screws did you use for the bed because the mandala rose one is thicker than the BOM
the best klicky probe manual! Thanks! probe accuracy results: maximum 2.732253, minimum 2.717253, range 0.015000, average 2.726253, median 2.727253, standard deviation 0.004359 a bit higher then yours
Great videos, I watched them to put my 2.4 together, but you were only up to the wiring stage at that point, so I came back to see where you are now. I see someone mentioned to you that you cable chains were backwards and it looks like you did tht for X and Y which fixed them. You should do the Z one as well, as I had the same on all of mine and although it is a pain, they look a lot better now.
I reversed my X and Y to look better. They do have issues this way though. If you don't get them just right they will lift the carriage right at the outer limits of travel or prevent the it from going all the way to the end. I almost think having them with the flexible end reversed may be a better solution. I'm not going to change them back though. I did find the spot where it doesn't lift and doesn't limit.
Thanks so much for your videos, I installed the klicky probe and macros and I'm having an issue as to when I home Z, the position thinks its 450mm from the bed and tries to dig into the bed, as such time I have to E-Stop. Discord forum said to wire the probe to the endstop for better results, but I don't know if that will help.
Thank you for this video. I tried doing TAP on my 350 but the resonance on Y is ridiculous. Going to try klicky to see if its better if if my problem is elsewhere.
HI Scott, cool vids. been following you for awhile now. I attached the klicky probe now. but suddenly i have a "BED_MESH_CALIBRATION" not found in gcode_macro. can you share wit me your BED MESH configuration. we have same build . 350mm. coz i am stuck now on this.. thanks in advance,
Awesome video! I'm looking at the MandalaRoseworks bed for my printer as well. Have you had any trouble with the magnets creating cold spots on the bed? I've seen thermal images of beds with magnets in them and the magnets are much colder than the rest of the bed. Also wondering what brand of flex plate you're using. Neither brand recommended by MR offers a textured plate option. Thanks!
Thank you! I've not had any issues with temperature with the bed. I do a 15 - 20 minute heat soak when I first start though. I'm unsure of uneven heating if you don't do a heat soak. The flex plate I'm currently using is a Fabreeko V2.4/trident Dual Sided PEI. It looks like it is sold out at the moment. The HoneyBadger single Sided black PEI Textured for voron V2.4 and Trident at Fabreeko would be about the same, but one sided and black. I have one of these, but I've not yet used it.
You need to put Variable_dockmove_x:40, Y:0, Z:0, and Variable_attachmove_x:0,y:30,z:0. I had the same issue and here onthis video Scott never mentioned hahaha
I've been working on a new video the last couple of evenings. It's slow at the moment because of my current workload. Hopefully soon. I don't think I have any commitments this weekend so far.
Scott great video I really appreciated your work back to shopping to buy Bed and Heather as you recommended this Voron is endless work and upgrade going to finish it up can you post a link where to buy the Heather and Magnetic Bed please Thank you
Awesome, thank you! kb-3d.com/store/voron/537-6678-mandala-rose-works-printer-bed-voron-v24-trident-ultraflat-magbed-1649814048366.html#/268-buildsizevrn-250mm/271-bedtype-ultraflat kb-3d.com/store/heated-bed-electronics/480-keenovo-silicone-heater-voron-fermio-340mm-750w-120v-1642958101997.html I buy a lot from KB-3D. He is a good guy.
I have so little spare time I would feel guilty taking memberships. I wouldn't be able to do anything extra for the members. l turned on super thanks last week but I'm unsure if it is showing up? Not that you would have to use it. lol
I am. I started a new job about the time I dropped off. It has taken up much of my time. The high heat we (and everyone) have been getting has been a hindrance also. When it is 100f it doesn't make me want to turn up a hot printer. lol I hope to get back to videos soon.
@@scottcorn I understand that it is also hot here, but air conditioning helps out. I started assembling 2.4 300 mm, I watch your videos, everything is just super, very nice to watch, everything is clear. I will wait for new videos
@@Константин-е2е5э Cool, I hope to get back to videos soon. It is cooling down to more normal this week here. Hopefully it will stay that way for the rest of the summer.
There was a version of mainsail maybe 18 months ago that had this problem is all that comes to mind. Have you refreshed the browser? Browsers tend to cache things. If the macro isn't in printer.cfg is the file included [include ] in printer.cfg? Sorry not being very helpful here. They should just show up.
@@scottcorn Thanks for the response. Yep, refreshed browser. The printer config file has the [include klicky_probe.cfg] command and the macros are referenced in that file. Frustrating.
Love the videos but the music selection man.. do you listen to these yourself or just for the videos? I can send over a playlist or two in the same style
Thank you. I don't listen to music much anymore so it's just for the videos. Yes you can send a list. If they are available as royalty free TH-cam safe I see about using them.
Thanks for all the video! I followed your video for the klicky install but it’s having issues homing since the z is out of range. I was going to try the virtual z to get unblocked but was just curious if the video is missing a step. Did you also do the Automatic Z Calibration ? I wasn’t sure if that’s optional or required. Thanks again!
I have not done the auto Z calibration. I started to and then I heard tap was close. As far as I can see I haven't skipped any steps. First thing is make sure you are getting the signal from the switch. If so maybe the safe starting Z height you entered in the config is too high? If not maybe your Z end stop maybe too high above the bed? (Shaft too long) Doesn't seem likely, but it's the only thing that comes to mind. The error seems to be that it didn't detect the click within the distance it thinks it should have.
Is there a voltage we trying to meet by magnet connection like 1.5v or it doesn’t matter? I followed same you but my probe in the machine tab wont change to trigger on switch click and hold.
I'm unsure of the voltage. Just make sure that there is continuity when connected to the wires. The continuity should stop when the microswitch is pressed. If no continuity check the continuity across just the magnets. If none there check across the pins of the switch. If none there the switch is bad.
Scott after following your Klicky configuration I get the error Klippy-stat: error Option 'mesh_min' in section 'bed_mesh' must be specified any idea what I di wrong Thanks
Sorry, was down and out with Covid this weekend. This usually is because there is an existing mesh in the config that isn't compatible. Go to your mesh screen and make sure any are deleted. When it is down to one mesh you have to reboot after deleting to get rid of it. Run the mesh again then and see if the error is gone.
I said the wrong screen. In Mainsail it is the heightmap screen. It is in the printer.cfg but it's in the do not edit area at the bottom under [bed_mesh default]. I would use the UI to delete it. It would be a good idea to see if you have an entry under [bed_mesh default] at the bottom though.
Great video as always! I just installed klicky and auto Z calibration macro as well - never have had better first layers, I'm very happy with it! :) Will you do auto Z as well?
Thank you. Yes, eventually I'll add the auto Z. I want to finish the printer in the next video. I'm going to add a revo in the video after that. The video after that will be the final (advanced) tuning. Then maybe the auto Z. Maybe should do the auto Z before the last tuning. lol I'm not sure right now.
@@scottcorn I would do it as quickly as possible. It's quite easy, just the switch offset calibration needs some time and work. And the benefit is huge IMHO.
I may do it and just document in a video later. Many are after me to finish the printer before modding it. lol This next video will finish the stock part of the printer. I do want to get the best print I can for the skirts. I know they aren't critical, but I don't want ugly.
I've been using and recommend the Panzer Observer. I used the OV5648 5MP USB Camera Module with it. I've not been real happy with it's video quality. The much cheaper HD version of the camera is worse though. github.com/Slidr666/VoronUsers/tree/18599db8c29c9a272f852d1dac9ad5d014d0a496/printer_mods/Slidr/PanzerObserver2.4
github.com/VoronDesign/VoronUsers/tree/master/printer_mods/JosAr/Klicky-Probe/Base_STL github.com/VoronDesign/VoronUsers/tree/master/printer_mods/JosAr/Klicky-Probe/Printers/v1.8_v2.4_Legacy_Trident/v1.8_v2.4_Legacy_Trident_STL The STL unfortunately aren't all in one URL.
I followed all your Voron videos, I must say these where more helpful than any other video on TH-cam, thank you very much, we need follow up videos on what you have been doing lately
Just finished my first 2.4 build, and I have to say this series of build videos is the best I have found, including build videos from well known Voron team members. Saved me a lot of time and grief in places where the printed manual was less clear. I also like that it is divided into manageable chapters, so it is easier to find what you are looking for without jumping around in a 6 hour marathon video.
Thanks alot!
No problem. Glad I was helpful.
I need to get back to creating the videos. Work and life has been keeping me overly busy.
I don't comment on youtube videos all that often, but I really wanted to say thank you for this amazing resource. As my first time working with Klipper this made the process SO much easier.
Wow, thank you!
Thank you so much for your wonderful series of videos on building a Voron 2.4. I finished building min last April and found your guides an invaluable resource. Keep up the good work!
Great to hear and thank you!
Thanks!
Your videos have helped me get my new Voron up and running and now Klicky working great!
Thank you! Your support is greatly appreciated!
Hi! Thank you! With proximity sensor I didn't even made first print and just finished klicky with your help! THANK YOU :)
You are welcome!
Luv the vids, and yes please do make vids on the modifications you are installing.
Thank you. I'll get back to videos soon.
Have a great weekend Scott. My Voron 2.4 350mm arrived today.
Thank you! Have fun with the build. I’m getting ready to head out and hopefully finish my first V0.2 build video.
your videos are so well made that even if i don't own a voron (yet) i'll still watch the entire build process to prepare myself for my future build.
thank you for this great content,
you should reach out to the voron guys and make this series a true build guide instead of the pdf manual!!! congrats man
Thank you. I need to get the skirt video done so I can say it is built. lol Life keeps getting in the way.
Built a voron 2.4 at the beginning of February and your videos were a huge help. I have doubts again and your video came to the rescue
again.
Thanks 😄
Very welcome!
Best series out there!! Thanks for all your work. My Voron 2.4r2 kit will be here in a week or so and I already have everything ready for Stealthburner except for your video! Let's go! 😀
Great to hear and thank you!
Great video. Really helpful on the config. Just set mine up with zero issues. Thanks for sharing
Thank you!
Thank you for putting in the time to document everything!
My pleasure! Thank you for your support!
great video, made getting a klicky probe set up on my trident super easy. Thanks!
Glad it helped! Thank you.
Best Clicky probe video EVER!!
Thank you!
Love your tutorials.
They are the best videos on how to build a voron on TH-cam. No one comes close tbh.
Because of you I've self sourced a V2.4 R2.
Watching your videos almost daily for the past 6 months.
One question though which screws did you use for the bed because the mandala rose one is thicker than the BOM
great video. Beats those never get to point "Hi Joe, Hi BobCat, thanks for the $5" livestreams
Glad you like them!
the best klicky probe manual! Thanks!
probe accuracy results: maximum 2.732253, minimum 2.717253, range 0.015000, average 2.726253, median 2.727253, standard deviation 0.004359
a bit higher then yours
Cool, I think that should work well for you.
Love these tutorials. Really helpful! Thank you!
You're very welcome!
Great videos, I watched them to put my 2.4 together, but you were only up to the wiring stage at that point, so I came back to see where you are now. I see someone mentioned to you that you cable chains were backwards and it looks like you did tht for X and Y which fixed them. You should do the Z one as well, as I had the same on all of mine and although it is a pain, they look a lot better now.
I reversed my X and Y to look better. They do have issues this way though. If you don't get them just right they will lift the carriage right at the outer limits of travel or prevent the it from going all the way to the end. I almost think having them with the flexible end reversed may be a better solution. I'm not going to change them back though. I did find the spot where it doesn't lift and doesn't limit.
I appreciate all your hard work I wish you had a link for me to buy you a coffee!!
Thank you. I have Super Thanks on here. Don't feel obligated just because I do. :)
Great job! Thanks to you, I will build my own voron. Can't wait for the next video :)
Thank you
That's so freaking cool!
Thank you!
Thanks so much for your videos, I installed the klicky probe and macros and I'm having an issue as to when I home Z, the position thinks its 450mm from the bed and tries to dig into the bed, as such time I have to E-Stop. Discord forum said to wire the probe to the endstop for better results, but I don't know if that will help.
Thank you for this video. I tried doing TAP on my 350 but the resonance on Y is ridiculous. Going to try klicky to see if its better if if my problem is elsewhere.
Good to know. I have the parts for tap, but just haven't had the time. I've got a v0.2 build series coming up so time doesn't get better. lol
Putting on the bed heater and wiring "see earlier videos". I went to your channel, I don't see them.
Any chance of you doing one of these EXCELLENT videos on TAP?
I have the stuff ordered to upgrade everything and plan on it. I just have to find the time.
Another great video ! getting my klicky soon
Thank you! Mine is still working well. I've been printing skirt parts all week.
How did you get the MCU and Pi temps in Mainsail please?
HI Scott, cool vids. been following you for awhile now. I attached the klicky probe now. but suddenly i have a "BED_MESH_CALIBRATION" not found in gcode_macro. can you share wit me your BED MESH configuration. we have same build . 350mm. coz i am stuck now on this.. thanks in advance,
you can see his mesh mesh in video 21
thank you man! i will have a look at it now.@@timtdp
thanks, your video helped me a lot
You are welcome!
Died you need an Klicky Probe, when you have an BL Toch instad of Inductive Sensor?
Nope, the Klicky Probe and BL Touch do the same job.
Awesome video! I'm looking at the MandalaRoseworks bed for my printer as well. Have you had any trouble with the magnets creating cold spots on the bed? I've seen thermal images of beds with magnets in them and the magnets are much colder than the rest of the bed. Also wondering what brand of flex plate you're using. Neither brand recommended by MR offers a textured plate option. Thanks!
Thank you!
I've not had any issues with temperature with the bed. I do a 15 - 20 minute heat soak when I first start though. I'm unsure of uneven heating if you don't do a heat soak.
The flex plate I'm currently using is a Fabreeko V2.4/trident Dual Sided PEI. It looks like it is sold out at the moment.
The HoneyBadger single Sided black PEI Textured for voron V2.4 and Trident at Fabreeko would be about the same, but one sided and black. I have one of these, but I've not yet used it.
@@scottcorn Thanks for the quick answers!
Nice video and music!
Thank you very much!
thank you so much for all your videos.. but i have a problem, if i try to home axes it show me ''move out of range'' do you have a solution for me?
Thank you.
What axis is it on when you get this error? XYZ?
You need to put Variable_dockmove_x:40, Y:0, Z:0, and Variable_attachmove_x:0,y:30,z:0. I had the same issue and here onthis video Scott never mentioned hahaha
When is the next vid, thas been 2 months
I've been working on a new video the last couple of evenings. It's slow at the moment because of my current workload. Hopefully soon. I don't think I have any commitments this weekend so far.
I get the error Existing command 'BED_MESH_CALIBRATE' not found in gcode_macro rename, any idea what this is?
you need to add bed mesh to your printer.cfg file
Scott great video I really appreciated your work back to shopping to buy Bed and Heather as you recommended this Voron is endless work and upgrade going to finish it up can you post a link where to buy the Heather and Magnetic Bed please Thank you
Awesome, thank you!
kb-3d.com/store/voron/537-6678-mandala-rose-works-printer-bed-voron-v24-trident-ultraflat-magbed-1649814048366.html#/268-buildsizevrn-250mm/271-bedtype-ultraflat
kb-3d.com/store/heated-bed-electronics/480-keenovo-silicone-heater-voron-fermio-340mm-750w-120v-1642958101997.html
I buy a lot from KB-3D. He is a good guy.
@@scottcorn Do you have plan to have Patreon on some sort of membership account so I can join
By the way I always buy it from him too currently he is out of the heather
I have so little spare time I would feel guilty taking memberships. I wouldn't be able to do anything extra for the members. l turned on super thanks last week but I'm unsure if it is showing up? Not that you would have to use it. lol
@@scottcorn I don’t see any super thanks anywhere understood short on time I bought my voron about 9 months ago and still don’t have time to finish it
Hello. I really like your videos, but there have not been new ones for a long time, are you all right?
I am. I started a new job about the time I dropped off. It has taken up much of my time. The high heat we (and everyone) have been getting has been a hindrance also. When it is 100f it doesn't make me want to turn up a hot printer. lol I hope to get back to videos soon.
@@scottcorn I understand that it is also hot here, but air conditioning helps out. I started assembling 2.4 300 mm, I watch your videos, everything is just super, very nice to watch, everything is clear. I will wait for new videos
@@Константин-е2е5э Cool, I hope to get back to videos soon. It is cooling down to more normal this week here. Hopefully it will stay that way for the rest of the summer.
@@scottcorn Yes, cold is better than hot :-). In winter, you can drink hot tea and warm yourself near the printer :-)))
Great vid. Wondering why my macros arent showing up on the dashboard? I have the proper cfg files uploadeded/installed/referenced.
There was a version of mainsail maybe 18 months ago that had this problem is all that comes to mind. Have you refreshed the browser? Browsers tend to cache things. If the macro isn't in printer.cfg is the file included [include ] in printer.cfg? Sorry not being very helpful here. They should just show up.
@@scottcorn Thanks for the response. Yep, refreshed browser. The printer config file has the [include klicky_probe.cfg] command and the macros are referenced in that file. Frustrating.
@@WeepingZeeGuitars That's strange. Can you manually enter the commands and it finds/executes them?
@@scottcorn No- Doesn't recognize commands.
Frustrating because the printer was working great before I decided to add the Klicky. If it aint broke, don't fix it!!!
When you connected the signal wire did you keep the diode or get rid of it?
I kept the diode. More just in case I use something in the future that requires it.
Love the videos but the music selection man.. do you listen to these yourself or just for the videos? I can send over a playlist or two in the same style
Thank you. I don't listen to music much anymore so it's just for the videos. Yes you can send a list. If they are available as royalty free TH-cam safe I see about using them.
Môžete mi poslať link na stl subory?
Great Videos! You help me a lot!
Glad to hear it! Thank you.
Thanks for all the video! I followed your video for the klicky install but it’s having issues homing since the z is out of range.
I was going to try the virtual z to get unblocked but was just curious if the video is missing a step. Did you also do the Automatic Z Calibration ? I wasn’t sure if that’s optional or required. Thanks again!
I have not done the auto Z calibration. I started to and then I heard tap was close. As far as I can see I haven't skipped any steps.
First thing is make sure you are getting the signal from the switch. If so maybe the safe starting Z height you entered in the config is too high? If not maybe your Z end stop maybe too high above the bed? (Shaft too long) Doesn't seem likely, but it's the only thing that comes to mind. The error seems to be that it didn't detect the click within the distance it thinks it should have.
@@scottcorn thanks for the fast reply. I figured it out. I was not able to home until i set variable_docklocation_x and variable_docklocation_y.
I see. You do need those. :) Glad you figured it out.
Is there a voltage we trying to meet by magnet connection like 1.5v or it doesn’t matter? I followed same you but my probe in the machine tab wont change to trigger on switch click and hold.
I'm unsure of the voltage. Just make sure that there is continuity when connected to the wires. The continuity should stop when the microswitch is pressed.
If no continuity check the continuity across just the magnets. If none there check across the pins of the switch. If none there the switch is bad.
@@scottcorn turns out it was the pin. I changed the plug from j40 to j34 and printer cfg for probe from ~PB7 to PB15. It started to work
@@deathgoku Cool, glad it worked out.
Scott after following your Klicky configuration I get the error Klippy-stat: error
Option 'mesh_min' in section 'bed_mesh' must be specified any idea what I di wrong Thanks
Sorry, was down and out with Covid this weekend.
This usually is because there is an existing mesh in the config that isn't compatible. Go to your mesh screen and make sure any are deleted. When it is down to one mesh
you have to reboot after deleting to get rid of it. Run the mesh again then and see if the error is gone.
@@scottcorn do you mean in printer.cft if so I just have
[bed_mesh]
speed: 300
horizontal_move_z: 10
I said the wrong screen. In Mainsail it is the heightmap screen.
It is in the printer.cfg but it's in the do not edit area at the bottom under [bed_mesh default]. I would use the UI to delete it.
It would be a good idea to see if you have an entry under [bed_mesh default] at the bottom though.
probe triggered prior to movement ，why?
Great video as always! I just installed klicky and auto Z calibration macro as well - never have had better first layers, I'm very happy with it! :) Will you do auto Z as well?
Thank you.
Yes, eventually I'll add the auto Z. I want to finish the printer in the next video. I'm going to add a revo in the video after that. The video after that will be the final (advanced) tuning. Then maybe the auto Z. Maybe should do the auto Z before the last tuning. lol I'm not sure right now.
@@scottcorn I would do it as quickly as possible. It's quite easy, just the switch offset calibration needs some time and work. And the benefit is huge IMHO.
I may do it and just document in a video later. Many are after me to finish the printer before modding it. lol This next video will finish the stock part of the printer. I do want to get the best print I can for the skirts. I know they aren't critical, but I don't want ugly.
great tutorial
Glad you think so!
Off topic here but what were your plans for the camera setup just curious lol
I've been using and recommend the Panzer Observer. I used the OV5648 5MP USB Camera Module with it. I've not been real happy with it's video quality.
The much cheaper HD version of the camera is worse though.
github.com/Slidr666/VoronUsers/tree/18599db8c29c9a272f852d1dac9ad5d014d0a496/printer_mods/Slidr/PanzerObserver2.4
Hello. what kind of bed do you have?
A Mandala Rose Ultraflat with magnets.
mandalaroseworks.com/products/voron-350-ultraflat-bed
why did change your probe for a Klicky?
The stock one wasn't consistent enough. Once I had removed it I could see it had started to melt and may have been the reason for this.
"Existing command 'BED_MESH_CALIBRATE' not found in gcode_macro rename" is what I'm getting hung up on after the steps at 27:00
I am getting this too
nice video. care to share your printer config files?
I don't mind sharing. I just need to figure out how to do that. lol
@@scottcorn thanks.
Thanks
Thank you!
When the next part ?
I'm hoping this weekend. Work has been all consuming the last couple of weeks. I'm away for work next week, so I'll try hard. lol
@@scottcorn Hi, how's the work situation? Do you have any plans for the next parts?
@@skmer4704 Yes, sorry work has been overwhelming. I'm hoping to get back to videoing this weekend.
Can you send me a link to stl files?
github.com/VoronDesign/VoronUsers/tree/master/printer_mods/JosAr/Klicky-Probe/Base_STL
github.com/VoronDesign/VoronUsers/tree/master/printer_mods/JosAr/Klicky-Probe/Printers/v1.8_v2.4_Legacy_Trident/v1.8_v2.4_Legacy_Trident_STL
The STL unfortunately aren't all in one URL.
@@scottcorn well thank you
i got a "Existing command 'BED_MESH_CALIBRATE' not found in gcode_macro rename error". Could you help with this?