How to install R.O. UV Filter with Flow switch.
ฝัง
- เผยแพร่เมื่อ 1 มิ.ย. 2024
- How to install an automatic start - stop flow switch / flow sensor to a UV filter
and how to install it to an existing Reverse Osmosis Water Filter System.
0:00 Introduction
0:58 INSTALLATION OF GLASS TUBE
2:11 WIRING CONNECTIONS
3:55 INSTALLATION OF FLOW SWITCH
4:46 U.V. LAMP INSTALLATION
6:19 INSTALLATION OF PRE-FILTER
6:51 INSTALLATION OF UV FILTER
9:28 Use of UVC Test Cards
Also included in the video, how to install a stainless steel mesh washable pre-filter.
If you have any questions, just leave it on the comments below.
If you liked this video, please don't forget to like and subscribe, and please hit that bell button.
Thanks for watching, till next time. :)
Please watch:
Reverse Osmosis water filter installation Tutorial.
• Easy DIY Guide: Settin...
Click here to subscribe:
/ @jongpenaranda
#uvsterilizer #reverseosmosis #flowswitch
Good day po sir, may water refilling station po ako at nag DIY ako ng vendo ko.. Issue nga Lang po is laging nk andar ang UV. Umiinit po sia, pag nilagyan ko po ng flow switch, dina po b iinit ang UV ko kahit parating Naka on ung switch ng UV?Salamat po
Does it shorten the lifespan of the bulb? Some folks said that turning on/off the bulb frequently shorten the lifespan of it. What is your experience about this? thanks!
Hi, have you tried using a dc flow switch with relay? The one you use po is made of brass, which leaches lead to your water...
No I haven't, I have to use this type of switch to match the voltage of my UV ballast.
With this small valve and small content of lead (if there is?) it wont matter....but anyway, most suppliers have a standard they follow regarding health and safety to pass product.
Very good tutorial but this will actually shorten the lifespan of your CCFL UV lamp..
You can actually do the same function using motorcycle horn relay, mas safe pang gamitin compare sa flow switch that is running on 220V AC.
"When the electrodes no longer emit sufficient electrons, the light burns out. As startup rapidly depletes the coating on the electrodes due to the high voltage required to get an arc going, frequent startups will shorten the life of the bulb."
Hi, thanks for the proactive input. That quote is applicable to larger UV systems which consumes higher wattage, but may also have less effect to home units since were using ''electronic ballasts'' nowadays. However, overheating of UV lamps also damages the coating due to continuous operation which is caused by less flow of water as cooling (in which has more disadvantages). If you have enough flow of water to cooldown your system or you're in colder areas, then this flow switch is not necessary. I myself in tropical area, using this design is more efficient when it comes to temperature issues and lesser electric consumption.
And for the flow switch itself, I have used in this video is a magnetic type switch. Which means the mechanical (water) side is totally isolated from the electrical side and the contacts are activated by a magnet, which means it is very safe even operating in 220V. Motorcycle horn relay is also a good idea but good luck with the complications with the voltage difference in your system. :)
@@jongpenaranda just match the voltage of your pump.. mine is in 12v so a motorcycle relay is perfect..
just turn ON the relay when the pump turns ON.. and your lamp will turn ON as well..
completely safe and economic.
@@garryboi15 Oh i see, i agree on that design is indeed more practical. But it can only sanitise water when pump is running only, meaning the UV lamp needs to be relocated before the water tank and not after. You just need to drain and clean your tank regularly though to lower risk of microorganisms that might grow in the system overtime since you cant efficiently place your uv on the final stage before faucet.
@@jongpenaranda you can place the UV lamp anywhere in the system, the pump is just the trigger.
as long as you did not add more air in your reservior.. it should match the pressure switch that the pump is set to operate.
it should turn on everytime you fetch water from the faucet.
Hi. Is it okay to use this flowswitch to 25Watts bulb? I saw the specs of the flow switch and it says 100watts. Thank you
Yes, you can use bulbs as long as it is below 100 watts.
Does it need to be series or parallel connection for the power is also ok?
The power should be in series connection with the main cable.
@@jongpenaranda ok thanks!
Good day sir, ur video was very informative, but would u have any insight regarding connecting a water pump to an automatic flow switch for a whole house for instant hot when the faucet is opened?
Hi thanks.
Technically you can apply this design with the flowswitch to your whole house (just connect to water heater outlet pipe and wire it to the pump) as long as you have enough water pressure to activate the flowswitch, if not then your pump wont start. If that's the case, I strongly suggest to use a pressure switch, it far more safe and efficient.
What model flow sensor is that? The first one I tried failed to turn off once activated, I think the system pressure was too high.
This model is a generic type so no specific brand. Try buying a sensor which has an adjustable sensitivity like on my video.
For those requesting for the product link, here it is:
Flowswitch:
Amazon US amzn.to/3QZwxWh
Lazada PH c.lazada.com.ph/t/c.YKnGsK
UV Lamp Filter
Amazon amzn.to/3CSGAqi
Lazada PH c.lazada.com.ph/t/c.YKq5wx
Thanks, couldn't find anywhere!
Sir ilang psi or gaano kalakas ang waterflow para mapagana ang switch? may nabili kasi ako na ganyan hindi po nagswiswitch kahit sa faucet ko na nilagay. sana masagot salamat
About 60-80 psi water preasure needed to activate. If you dont have enough pressure, positioning the switch vertical with the flow will help, but will have a risk that it will stay activated. Also try adjusting the sensitivity.
sir penge ng link kung saan nyo nabili yan flow switch? yung nabili ko kasi di nagtagal.
Not related to seller, but just sharing. Mine is 6 months old and still in good working condition. www.lazada.com.ph/products/ht-200-g12-g12-thread-220v-water-pump-flow-sensor-automatic-control-switch-i1127792144-s3911822482.html
where i can buy
You buy it online at Lazada.
www.lazada.com.ph/products/ht-200-g12-g12-thread-220v-water-pump-flow-sensor-automatic-control-switch-i1127792144-s3911822482.html
boss pwede ba tanggalin na lang yung tank? yung diretso na lang para di na magipon ng tubig. possible ba yun sa ganyan system
Di pwede boss kasi mahina lang pressure ng pump installed.
Double purpose kasi yung tank, it serves as storage and buffer/accumulator para magkapressure system mo.
If you remove the tank, it will take you approx 1 to 2 minutes to fill-up a 300ml cup.
boss isa pang question, anong brand ng water flow switch magandang bilhin? may mga nakita kasi ako sa shopee na pumutok agad.
@@raffy3304 Hi sorry i missed your other question. Buy the magnetic type flowswitch same model on my video. It is safe even running in 220V since the electical and mechanical sides are totally isolated. Mine is working for 5 months straight up to now woth no issues.
same lng ba yan sa waterpure na brand..
hola hice todo lo mismo que tu y se me queda el sensor activado
Hi, please adjust the sensitivity of the sensor and make sure that it is installed horizontally. If still activated, maybe it is deffective. To confirm function, move flap of flow switch with screw driver while electrical circuit is connected or use multimeter.
And lastly, make sure you reached the minimum line pressure of your flow switch. About 60 to 70 psi.
Di po b malakas ang kain s kuryente pag laging Naka on ang UV?Salamat po
it depends sa size ng uv lamp/s mo. Ok lang if 50-100 watts, pero i suggest for a flowswitch para di uminit masyado and maextend life ng UV lamp gas and coating. But if you have multiple UV lamps, then malakas yan sa kuryente.
S water refilling station po, ano pong dapat n variation, 100w or 260w? S lazada kc may dalawang variations?
Ne ho comprato uno preciso su amazon ma non funziona, in pratica appena apro l'acqua si accende ma dopo mon si spegne piu
Hi, idont really understand what you mean. But you need to adjust sensitivity of the flowswicth according to the pressure you have.
Why do you need a UV filter if the RO filters everything out including viruses and bacteria?
I added my UV filter as an extra precaution to get optimum removal of unwanted micro organisms. In addition, through time of use with your RO system, the efficiency drops and this may cause bacteria build up on the pressurized tank in which we cant clean regularly.
Nag iinstal pb kau??pede makuwa mobile number nio
Hi, sorry just DIY lang for the video. Installations are very easy to do, just follow the video step by step. Or I can answer some of your questions.
Boss, bakit tuloy-tuloy yung overflow ko?
@@chitoramos681 Could you pls elaborate. Do you mean you've got continuous waste water flow? It should only be flowing while the pump is running only.
a