I have a Nikon D810 that has been to Nikon repair center 3 times for the same issue. They say they can't duplicate the problem even though it is the same every single time I check. I'm wondering if you have any idea.... When auto focusing I get a sharp image but the image in the optical viewfinder is not sharp. If I change to manual focus and achieve sharp focus in the ovf then my resulting image is out of focus. It is 100% not a diopter adjustment issue as I wouldn't be able to get a sharp image in the viewfinder when manually focusing. If I shoot somewhere between f/11 and higher then I can get an acceptable image. I'm not sure if it is front or back focusing but I think front. Is there a coupler somewhere internally that could be very slightly out of adjustment? Any ideas?
Hi there! Thanks for your helpfull video! I have a similar problem with a D5100, power reaches motherboard, but no life in camera.. What would really be helpfull if you could share more details on the Power-driver-chip you have replaced (specific location? foto? type-number of chip?, where did you get spare-part?). Would be great 🙂Thanks!
i have nicon 100D and after year of no use it just died . changed the batery and stiil dead . any ide of what might go bad ? and how do i test the power supply and main board ?
I had the following thing happen with my machine. I have a Nikon d5300 and all of a sudden it crashed at an event, it literally wouldn't turn on at all just the led flickered when I turned it on green. Two days later when I checked again the camera already turned it on but strangely when it was on the camera was actually off and when off then it was on. I once put it on off thinking they had turned off and after a few days when I wanted to use the machine it was completely discharged. After about a month again it wouldn't turn on. The battery I checked and there's no problem with it. I wonder what could be wrong with it?
there a problem on rhe mainboard.. first check the power supply section if thw a short circiits in there..common problem is the chip on power supply section of the mainboard
Hello, what would be your first opinion on a Nikon D7200 that does not give any sign of life? Battery and charger OK, Battery connector clean. Is there more chance that it is the DC/DC board (fuse?) or the motherboard on this model? I can't find much information on Google (and no repair manual).
check first the primary power supply of the camera near the battery ,check the fuse and if there is a supply output to mainboard..try to disconnect the that supply , if you measure a 7.4 volts then connect to the mainboard if voltage will drop is has a short circuits in the mainboard
@@copaindu49 try to find the short in the mainboard..supply 7.4 volt the mainboard then touch the components and find the component that are overheating ...sometimes you will see it burning if you supply the board a few minutes
JPARTNERS REENGINEERING CONSULTING 0 seconds ago please have a problem with my d5000, on the process of updating the firmware on my Nikon d5000 it went off without competing the process, since then the camera is off please to advise
Thanks for filming this and sharing with us! How do we find the short in the main board? What kind of test or tests can we do? Can we just buy a main board and just replace it? If so, where would I find it?
@@powerofknowledge7771 check first the supply from the battery and check the circuit in there if there no supply may be there a open fuse,see it in my video..
Hello techxian, Great instructions to open D5300 up. I followed your instruction on my D5300, and found there is no 7VDC power reaching the four pins (White-Orange-Blue-Grey). The max is b/w White - Red is 0.2V. Battery by itself looks good as it show 8.1VDC. The camera got water splash on it momentarily and has not powered up since then. What can recommend to check further or maybe a problem? Thank you!
sir saan kayo loc papaayos sana ako ng d5000 nikon ko, battery ito po error nya "This battery cannot be used. Choose battery designated for use in this camera"
Thanks for the video. Can you help me with information? I connected a higher voltage source to my camera, and since then it hasn’t turned on anymore. Would it be necessary to change the main board?
check first the circuit near the battery if there an open fuse and measure also the supply to the main board if there a supply 7.4 ...then its need to replace the mainboard because of over voltage
@@techxian Hello Friend. Thanks for the answer. I changed the PCB and the camera is running, but it doesn't display anything on the screen. The screen is lit but without information. Do you know what this problem could be?
Hello sir , i also have one fujifilm digital camera its also no turn on with battery but it power on with DC power supply of 5v , actual camera have 4 AA battery slot i also checked with new battery but not power on please any solution 🤝
check the contact of the control panel may be there are broken connection...use magnifier or miscrope to see the broken connection..usually it happen when not properly inserted to the socket or accidentally bend the contact
Sir my nikon d3300 flash is not working.. When flash is open camera does not click photo. When flash is closed camera clicks photo.. Should I change the main board? Plz help this camera is very imp for my masters degree.. I am stuck
@@ziaahmad8669 bring it sir to the trusted technician in your country..im in the Philippines that why i can repair you camere but in my experience in nikon camera the common problem with your camera is the flash module...replace the module to solve your problem sir
@@techxian i am from Srinagar j&k and in my state their is no technician. Now i opened my camera last night.. At the top there is a board.. Should i change that entire board?
My camera is working but there is no display and I saw through the viewfinder the err message is display .. please help me ..where is your shop .. please fix my Camera ..
Hindi na po nag t turn ON yung D3300 ko kahit fully charged na po yung battery nya. 3 years ago pa yon and ngayon ko lang nakita video mo. Kaya mo po ba yon maayos? If yes, how much po? Nasa bicol pala ako.
try first to reset the camera..you will find it in menu..if does not work there maybe a short button or open connection...is your camera splash with water or liquid? do you bring it near to the beach?
@@vinhofrancisco maybe the polarity of the dummy battery is been reverse and cause the camera not to powering on or the adapter if too high dc output, check it with voltmeter and double check the polarity
Hello, i hope mabasa nio po. I was taking a photo with this same model, and suddenly nag error ang SD Card so i took it out without turning it off, tas bigla nag nag shutdown tas hirap ko ng ma on, minsan nag o-on pero madalian lang tas patay ulit. 😭 Tas sa viewfinder parang nag grainy na greenish siya 😭 Ang sensitive pala ng mga dslr 😭 Diko alam kung paano, sa papa ko pa naman Thank u po
pwede may nagshort s slot ng card sir..free check up nman s shop nmin..kung madadala mo sir s sta cruz laguna..techxian camera repair service,yan din page ko s fb
thanks you sir for the correction...the problem that i encountered in that camera is the shorted driver ic at the power section.,i replace that driver ic ,it is more cheaper than to replace the whole mother board of the camera...
nice. you actually did not show how you repaired or replaced the broken part.
I have a Nikon D810 that has been to Nikon repair center 3 times for the same issue. They say they can't duplicate the problem even though it is the same every single time I check. I'm wondering if you have any idea....
When auto focusing I get a sharp image but the image in the optical viewfinder is not sharp. If I change to manual focus and achieve sharp focus in the ovf then my resulting image is out of focus. It is 100% not a diopter adjustment issue as I wouldn't be able to get a sharp image in the viewfinder when manually focusing. If I shoot somewhere between f/11 and higher then I can get an acceptable image. I'm not sure if it is front or back focusing but I think front.
Is there a coupler somewhere internally that could be very slightly out of adjustment?
Any ideas?
Hi there! Thanks for your helpfull video!
I have a similar problem with a D5100, power reaches motherboard, but no life in camera..
What would really be helpfull if you could share more details on the Power-driver-chip you have replaced (specific location? foto? type-number of chip?, where did you get spare-part?). Would be great 🙂Thanks!
Thanks for this useful video
i have nicon 100D and after year of no use it just died . changed the batery and stiil dead . any ide of what might go bad ? and how do i test the power supply and main board ?
If the main board of Nikon d3300 had short circuit due to aunt's. And the LCD was blinking when it is off and On . It can be Fix?
it isposibble to replace the mainboard if that is the problem of your camera sir..
I had the following thing happen with my machine. I have a Nikon d5300 and all of a sudden it crashed at an event, it literally wouldn't turn on at all just the led flickered when I turned it on green. Two days later when I checked again the camera already turned it on but strangely when it was on the camera was actually off and when off then it was on. I once put it on off thinking they had turned off and after a few days when I wanted to use the machine it was completely discharged. After about a month again it wouldn't turn on. The battery I checked and there's no problem with it. I wonder what could be wrong with it?
there a problem on rhe mainboard.. first check the power supply section if thw a short circiits in there..common problem is the chip on power supply section of the mainboard
@@techxian Can it be repaired and about how much would the repair cost me?
Hello, what would be your first opinion on a Nikon D7200 that does not give any sign of life?
Battery and charger OK, Battery connector clean.
Is there more chance that it is the DC/DC board (fuse?) or the motherboard on this model?
I can't find much information on Google (and no repair manual).
check first the primary power supply of the camera near the battery ,check the fuse and if there is a supply output to mainboard..try to disconnect the that supply , if you measure a 7.4 volts then connect to the mainboard if voltage will drop is has a short circuits in the mainboard
@@techxian Ok thank's :) If the mainboard have a short circuit, it's more simple to replace or investigate the short circuit ?
@@copaindu49 try to find the short in the mainboard..supply 7.4 volt the mainboard then touch the components and find the component that are overheating ...sometimes you will see it burning if you supply the board a few minutes
@@techxian Thank's for your informations !
JPARTNERS REENGINEERING CONSULTING
0 seconds ago
please have a problem with my d5000, on the process of updating the firmware on my Nikon d5000 it went off without competing the process, since then the camera is off please to advise
go to the nikon service center in your area for updating the firmware of your camera,maybe its been corrupted due to unfinished process of updating..
I have the same problem, which part was defective?
the chip in power supply section sir i find in this camera.m
@@techxian and what is the name of this chip? I haven't opened the camera yet.
that chip is at the back of the sd card slot ..i cannot recall the number..
Where is your store, I need to get my Nikon 3200d fixed shutter locked and power fluctuations
we are here in sta cruz laguna philippines sir
Plz aap bata skte hai nikon 5300 ka power drive ka cost kitna hoga agar replace kre to qki camera on nhi ho rha hai
Your shop location po? Tamron lens for cleaning required po.
Location kaha he
Thanks for filming this and sharing with us! How do we find the short in the main board? What kind of test or tests can we do? Can we just buy a main board and just replace it? If so, where would I find it?
I bought new batteries for my camera and it's not working. But the camera worked when I had put it away for a few years.
@@powerofknowledge7771 check first the supply from the battery and check the circuit in there if there no supply may be there a open fuse,see it in my video..
Hello techxian, Great instructions to open D5300 up. I followed your instruction on my D5300, and found there is no 7VDC power reaching the four pins (White-Orange-Blue-Grey). The max is b/w White - Red is 0.2V. Battery by itself looks good as it show 8.1VDC.
The camera got water splash on it momentarily and has not powered up since then. What can recommend to check further or maybe a problem? Thank you!
check the mainboard and powerboard if thera a corrosion if the corrosion reach at the mcu replace the mainboard..
sem problem of my camera.lastnyt i remove the lense i forget to off cam on off.tel now not wrking battery is ok..
Sir app kaha se he please bataea mera 3100d kharab hogaya repair karni he😢
Sir my dssler camera is not getting light in the display what could be the problem 🙏🙏🙏
is there a display on the eye piece sir?
@@techxian sir ji everything is ok... photo tu utha rha ha but display light show nahi ho rhe ha(photo show nahi ho rha ha display pr) plx help me
Wetar damage camera 5600 thik hoga Kiya
U from
its 50/50 chance to repair that sir..if the mainboard has a corrosion and the other parts i think its worth to repair the camera
Bahii mara jo nekon camra ha .us ma jb card lagata ha wo lagta nahii ha
Both card try keya
Thanks for the “how to”🍺🍺
sir saan kayo loc papaayos sana ako ng d5000 nikon ko, battery ito po error nya "This battery cannot be used. Choose battery designated for use in this camera"
Bro I have this problem now what should I do I want to contact you how to do it😢😢😢😢
what the problem of your camera sir?
Can you show how to fix the back wheel?! THX!!!
Magkano po bayad sa labor Sir & ma'am...
Thanks for the video.
Can you help me with information?
I connected a higher voltage source to my camera, and since then it hasn’t turned on anymore.
Would it be necessary to change the main board?
check first the circuit near the battery if there an open fuse and measure also the supply to the main board if there a supply 7.4 ...then its need to replace the mainboard because of over voltage
@@techxian Hello Friend. Thanks for the answer.
I changed the PCB and the camera is running, but it doesn't display anything on the screen. The screen is lit but without information.
Do you know what this problem could be?
@@Klysman08 check the contact of the lcd using microcope or manifying glass may be there a open connection now
Disply ic perobalm sir
How much it cost to repair the display of my nikond5300 is not working.. it was stocked during covid
lets check first the camera maam..free estimate nman kami
Hello sir , i also have one fujifilm digital camera its also no turn on with battery but it power on with DC power supply of 5v , actual camera have 4 AA battery slot i also checked with new battery but not power on please any solution 🤝
check the battery terminal maybe its been loose connection try to clean the contacr of the terminal
El cable de video de mi nikon D5300 se rompió y no eh encontrado quien me consiga el repuesto y se lo cambie, me puedes aconsejar que puedo hacer?
sir saan po kayo sa manila? d3400 no power.. nag moist lcd from high temp.. nawala naman po ng onti ung moist from the LCD
s may sta cruz laguna n po ako sir wala po ako s manila...techxian camera repair service po kami..free check up nman po kami..
Sir mere cmare ki flash 1 photo m on hoti h or 1 photo m on nhi hoti kya prblm h
i cannot understand sir...you mean to say is the flash is the problem of your camera it only work at one photo shot?
how much does it cost for the repairs? my D5500 won't turn on even though the bettery is fine :(
im from the Philippines sir...the coast of repair of that model is 2500 pesos
@@techxian ah thank you, you guys are within hidalgo po diba? yung store niyo?
open po ba kayo ng Saturday?
@nuggerboi8278 sta cruz laguna n po ako sir..techxian camera repair service
@@techxian Copy that sir will be seeing you tomorrow
how much does it cost ??
in our shop we repair it at 2500 pesos
D 5200 Nicon camera ka motherboard kitne ka hoga
In mu nikon d5300 memory slot was damamged...i replace it successfully but when i turn on...showing only used designated battery
maybe there a open wiring or short part near the card slot ...
@@techxian Yes i got it..and resolve it already..thank you man 😍🙏
Nikon d 5300 menu,play, delete and others buttons not working .... please help
check the contact of the control panel may be there are broken connection...use magnifier or miscrope to see the broken connection..usually it happen when not properly inserted to the socket or accidentally bend the contact
Ok I'll check
And also... Metering malfunction problem
Same problem me faced Motherboard problem..
Sir my nikon d3300 flash is not working.. When flash is open camera does not click photo. When flash is closed camera clicks photo.. Should I change the main board? Plz help this camera is very imp for my masters degree.. I am stuck
there a problem in flash module, the flash capacitor is not charging that why the camera will take a photo when the built up flash is pop up..
@@techxian how can I get in touch with you.. Plz plz it's urgent for me.. My college is opening next week and my camera flash is not working
@@ziaahmad8669 bring it sir to the trusted technician in your country..im in the Philippines that why i can repair you camere but in my experience in nikon camera the common problem with your camera is the flash module...replace the module to solve your problem sir
@@techxian i am from Srinagar j&k and in my state their is no technician. Now i opened my camera last night.. At the top there is a board.. Should i change that entire board?
Btw thanks for replying.. You are so helpful. I will share yr channel to everybody i know.. Thanks a lot
I have a battery drain problem in my nikon d5600
Kaha so bhai
My camera is working but there is no display and I saw through the viewfinder the err message is display .. please help me ..where is your shop .. please fix my
Camera ..
I'm also facing the same issue...is your problem gets resolved? If yes..which component you've replaced?
Kitna pesa lag jayega
Same problem no on camera .solf plz
Good work
sir hm mag pagawa ng ganyan pero sony A6000 power din sira shorted din yung board
mga 3500 sir po ang gawa nun...kapag d po narepair palit n po ng mainboard
Hindi na po nag t turn ON yung D3300 ko kahit fully charged na po yung battery nya. 3 years ago pa yon and ngayon ko lang nakita video mo. Kaya mo po ba yon maayos? If yes, how much po? Nasa bicol pala ako.
try n lang nating sir gawin, no fix no charge nman kami..mga 2500 kung magagawa
@@techxian
Ah, any way na ma contact po kita and saan ko po i se send? :D
Whatcu need na ipa ship ko po aside sa camera body?
@sirwillemgaming9686 may pages po kami s fb sir techxian camera repair service.. yon address ko s sta cruz laguna po
How to fix metering error for Nikond D5300?
what metering error you mean sir? is there a display in the lcd screen?
@@techxian yes.. i cannot change to auto mode or others programme
try first to reset the camera..you will find it in menu..if does not work there maybe a short button or open connection...is your camera splash with water or liquid? do you bring it near to the beach?
Open the camera theres a metering cable inside disconnected it will work like q charm
@@shito4k open then?
Lovely
How much po repair po ng sensor ng D5200 ng nikon
wala po kami pamalit sir n image sensor pero pwede kayo magorder s aliexpress tapos pwede po kami maginstall
My Canon m100 won't turn on also
in some case of that model the flexwire of lcd monitor is been damage, check that first
I inserted a dummy battery then after a few moments it won't turn on anymore
@@vinhofrancisco is that dummy battery have a dc supply from ac adaptor?
Adapter from a huawei charger
@@vinhofrancisco maybe the polarity of the dummy battery is been reverse and cause the camera not to powering on or the adapter if too high dc output, check it with voltmeter and double check the polarity
Hello, i hope mabasa nio po.
I was taking a photo with this same model, and suddenly nag error ang SD Card so i took it out without turning it off, tas bigla nag nag shutdown tas hirap ko ng ma on, minsan nag o-on pero madalian lang tas patay ulit. 😭
Tas sa viewfinder parang nag grainy na greenish siya 😭
Ang sensitive pala ng mga dslr 😭
Diko alam kung paano, sa papa ko pa naman
Thank u po
pwede may nagshort s slot ng card sir..free check up nman s shop nmin..kung madadala mo sir s sta cruz laguna..techxian camera repair service,yan din page ko s fb
Apna no dena bhai
kuch aap ne aisa haraami pann kiya hai jo kuch samajh nahi aa raha hai
You really show us how to fix the power supply. All you showed us was how to take this camera apart. Delete this video.
thanks you sir for the correction...the problem that i encountered in that camera is the shorted driver ic at the power section.,i replace that driver ic ,it is more cheaper than to replace the whole mother board of the camera...
Hello brother my Nikon d5300 camera on nhi ho raha hai gir pada hai send your number help me
im from sta cruz laguna philippines sir..what the problem of your camera?