My grandfather had a Cub back in the 50's, he flew it from Washington to Oregon to go on dates with my Grandma (he was way cooler than me:P). He also loved to and could build pretty much anything, seems like a fun project.
Im going to be honest here; i was expecting some barely flying plastic thing but im really surprised (in a good way) of the building quality and looks of this cute Piper Cub. Well done, hats off to you Sir!
What a fantastic video - thank you for answering a load of questions through making such a thorough job. You have fantastic attention to detail. Clear Skies!!
Beautiful hand painting work looks good I do same thing I hand paint with sign painting paint and brushes like old school sign lanterns for my pinstripes and designs on my 3d printed planes or sometimes I'll 3d print it in the main color then paint the design on to it saves time and few bucks in paint
Another masterpiece from this man,the only channel that i don't joke with it's upload notifications 😅 good job man💓 Hats off to you,i would bring my questions later after studying the video😍
Hey, thanks for the videos, when I installed the code I have a lot of files, but you in your video you are using just about 25 pieces.So do I have to print every single piece?
I'm having good luck printing the outer surfaces, but those little support tubes for the ailerons keep falling out on me. It's impressive how light the prints are though :)
HI i have question i might travel to turkey and wanted to fly rc airplanes there do u have any ideas what is required for license to get to fly there also the shops i can buy parts from if u can plz inform me also promodel donst have much of parts if u can tell me about more shops ty!!
Merhaba, bir sorum var, türkiye'ye seyahat edebilirim ve rc uçakları uçurmak istedim orada herhangi bir fikriniz var mı oraya uçmak için lisans için ne gerekiyor ayrıca parça satın alabileceğim dükkanlar eğer yapabilirseniz lütfen beni bilgilendirin ayrıca promodel çok fazla bir şey yok Bana daha fazla mağaza hakkında bilgi verebilirseniz, parçaların!
Hi, quite new to rc and doing this for a school club. How did you connect/pair the remote to the controller system? Is there a general guide to do so? thanks.
This is not the same for every brand, but in general matching the transmitter and receiver is a simple procedure. Search with the word "BINDING" for the brand and model you are using. You can find many resources.
Normal PLA kullanınca ağırlık artacağından dolayı daha farklı bir batarya kullanılabilir mi? Ne olabilir? When we use normal PLA instead of LW PLA, is it better to use different battery? What it could be?
Merhabalar yorumunuzda da bahsettiğiniz gibi normal pla ile uçağı basmayı denediyseniz biraz bilgi verebilir misiniz ? Uçağın kalkışta yaşadığı sorunlar oldu mu veya daha hafif hale getirebilmek için izlediğiniz yollar oldu mu oldu ise bahsedebilir misiniz ? Şimdiden teşekkürler.
@@MehmetEmirŞahin-1 Bu modeli normal pla ile basmadım. Mecbur kalmadıkça bu kadar küçük modeller için pla kullanılmamalı. LW-pla ya göre ağırlık dezavantajları önemli çünkü. 130-150cm kanat açıklığı olan modellerde normal pla kullanıyorum. Örneğin planeprint firmasının Tucano modeli gibi. Sorunsuz baskı ve güzel uçuş sağlıyor. Ama küçük modeller için ideal değil.
KendinYap great video, and thank you for sharing your 'skill'. Can you please explain why you choose to use diferent motor 2212 (recomended is 2830)? In 'coments' someone ask you if he can use 3s 1300mah battery, you say no, but in manual recomended battery is 3s 1300mah? I am guesing, but, this is why you must use 30g of 'ballast' to get a right cg.?
Thanks.. The recommended 2830 is the same motor as the 2212 I am using. Why? :) Motor manufacturers use two different standards. Some brands use the outer body diameter of the motor, some brands use the inner rotor diameter. The value 22 is the rotor diameter inside. The value of 28 is the outer casing diameter of the motor. The outer body diameter of 2212 is also 28. Most of the big and high quality brands identify with rotor dimensions. The most accurate description is the rotor dimensions. The other is misleading. The technical values of the Emax XA2212 I use and the recommended motor are similar. Why I used 1000mah battery. The problem is not about weight. Dimensions are a problem.. The nose area of this model is very small. It is impractical for me to insert and remove the 1300mah battery.
@@Kendin-Yap thank you for 'clearing' that out. Great. Thumb up ;) I really don't wanna to 'mess' with you, your choice, Emax XA2212 is the 'best' motor for Piper CUB? And in your 'raw' video of flight with Piper CUB your flight time was cca 4.30 min? That is max flight time on 1000mah 3s battery, or you just get bored ;) ?
Settings vary by machine. You should use the settings that the designer posted on his site to get started and find the appropriate settings for your particular machine with a bit of trial and error.
In general, I used the settings specified by 3Dlab. I made minor changes to the nozzle temperature and flow settings. You may need to adjust these two depending on the filament brand you use and your 3D printer.
Using PLA as a joint instead of carbon fiber seems like a decision that may come back to bite you later. It’s just not resistant to much force. Why not carbon fiber or steel rod?
You can’t print lw-pla without stringing which is why all these 3D printed plane companies use as little travel as possible. He probably just used the g-code that comes with it. I’m going to start printing this tomorrow and the only change I’m making for the ended 3 pro is the retraction in the g-code.
@@polar1991 I was able to get great results with PRUSA Slicer, worked much better than CURA, just one last question do you print this plane wall width with 0.4 or 0.8 wall width? 0.4 seems to thin for me.
@@arrie1978 I haven’t figured that out yet. There is a guy named Troy McMillan which has a channel that is all about 3D printed rc planes and he has a video on the best settings for lw pla planes. Hope this helps
Printed parts will be approximately 40% heavier. That's a little too much for a small plane. It does not prevent it from flying. But Stall speed will increase.
Being that I live in a 5th wheel, don't have space for 3d printer, do you sell the printed parts for people to build their own planes. I understand I will need to get al the extra stuff to make if fly
Ben de normal pla ile basıyorum. Yuzde kac dolgu ile bu agirliga ulasiyorsunuz? Eger ucarsa , agirligun hareket kabiliyeti ve havada kalma suresini etkileyecegini dusunuyorum.
@@ahmetinanc9534 Tasarımcının beyanı o şekilde olduğu için not olarak yazdım. Ama modeli orjinalde LW için tasarlamışlar. PLA ile basıldığında ekstra ağırlık modelin uçuşunu olumsuz etkiliyor. Minumum tutunma hızı artıyor. Uçuş süresi azalıyor vs. O yüzden ben tavsiye etmiyorum. Ama yine de siz bilirsiniz.
Tolles Video, sehr gut gemacht! Danke! Ist es möglich, dass Sie hier Ihre Druckparameter für das eSun LW/PLA zur Verfügung stellen? Das wäre großartig! Danke!
I have a Bambu Labs printer using Bambu Studio, which isn't recognizing the interior geometry of most of the parts. Just the external geometry. Fuselage #1 printed just fine. Everything after that has been a bust.
The bamboo silcer is very new. I don't think it has some of the print settings needed for airplanes. Designers will probably make improvements on this issue in the future. Prusa silicer also did not support this a few years ago.
My grandfather had a Cub back in the 50's, he flew it from Washington to Oregon to go on dates with my Grandma (he was way cooler than me:P). He also loved to and could build pretty much anything, seems like a fun project.
Im going to be honest here; i was expecting some barely flying plastic thing but im really surprised (in a good way) of the building quality and looks of this cute Piper Cub. Well done, hats off to you Sir!
Yes
I just buy a new 3D printer because of your kind contribution! Cheers !
I like that bit of cinematography where the shot is from inside the fuselage. Well done.
One of the best assembly vids ive seen. Well done
What a fantastic video - thank you for answering a load of questions through making such a thorough job. You have fantastic attention to detail. Clear Skies!!
To prevent the wings from sagging due to sunlight, we recommend 1mm carbon rods instead of filaments.
It's melted??
@@achmadiqbal80 pla easy to deform under heat
was super satisfying to watch
herzamanki gibi 10 numara 5 yıldz.. süper oldu.
WORLD CLASS bir kanalsınız. Maşallah. Gurur verici. Teşekkürler video için.
Brilliant... I love the filament hinges!!!
Teşekkür...!
Thanks for your updated session.
"Usta, zor olanı kolay gösterenmiş" Eline sağlık usta
Estos son los videos que animan a la gente a hacer cosas por uno mismo. Excelente material, gracias!
Beautiful hand painting work looks good I do same thing I hand paint with sign painting paint and brushes like old school sign lanterns for my pinstripes and designs on my 3d printed planes or sometimes I'll 3d print it in the main color then paint the design on to it saves time and few bucks in paint
Just started building that model. The holdup was getting a printer that could do a decent job of printing it (that being a Qidi X-Max3).
Wow your amazing with all your ideas you inspired me to build my own foamboard airplane. I'm going to maiden it this week. 😊
Thanks for your updated session. I'll watch your later. I'm in my work LOL - I need your tutorial soooo much
çok güzel uçak emeğine sağlık kolay gelsin 👍
Really well done. Great job
Nice plane! It has a lot of great design features.
I wouldn't recommend painting PLA black when you want to use it outside on a sunny day! ;)
Awesome build and footage though!
Pilotajında süper işçiliğine üstad tebrikler...
Another masterpiece from this man,the only channel that i don't joke with it's upload notifications 😅 good job man💓 Hats off to you,i would bring my questions later after studying the video😍
Güzel bir proje daha. 👍
Prodüksiyon gelişmiş elinize sağlık 😁
Sana helal olsun kardeşim
professional work, Thanks my friend ♥️♥️♥️♥️♥️♥️♥️
First like and first view...love from India ❤️
Nice video
this is awesomeeee, i might print this because ive got a 3d printer, some extra filament, and time. and i really want to start flying rc planes
okay i downloaded the files, what do i do now, i cant open tem in my slicer, so like how does this work
@@Evan-rq2ee Bro please share the downloaded file , i cant download it
Good stuff as always
hello.
it so beautifull...
can you add mpu6050 and oled to your handmade 6 channel arduino nano radio control?
mpu6050 is more important...
abi videoların çok güzel inşallah çok daha büyürsün emeğin in karşılığını alırsın
çok başarılı bir çalışma olmuş bu uçağı uçururken kuyruk kısmına renkli duman ekleseydiniz harika bir şov olurdu elinize sağlık
excellent work!
I love your videos! I would like to show you my project of DIY plane mixing 3D printing + foamboard!!!
Elinize sağlık yine süper olmuş.
Desde Argentina te felicito por lo simple y practico. Estoy armando uno, espero que me salga parecido al tuyo !
Harika olmuş
Hey, thanks for the videos, when I installed the code I have a lot of files, but you in your video you are using just about 25 pieces.So do I have to print every single piece?
Hello, I noticed that inside of parts there is almost no stringing. It's remarkable wit LW PLA. Could you please give some insight into settings?
There is a link below the video. There are details for the necessary settings on that website. I applied those settings.
I'm having good luck printing the outer surfaces, but those little support tubes for the ailerons keep falling out on me. It's impressive how light the prints are though :)
Ellerine sağlık yine efsane olmuş 🔥🔥🔥
que aeromodelo lindo....parabéns!!!!!
Can we use 3000 mah battery?
No you can't. it is very big and heavy.
Great video... I am in the process of building the same Piper Cub. What yellow paint did you use?
Use yellow filament
New sub! Liked 🙏🚀👍👍
En sevdiğim model
very nice !!! tank you !!!
how do you gut your pieces to snap together so cleanly? i been trying to make this plane for the past 2ish weeks with zero success
Where did you get the rudder and elevator push rod from? Can't find any long enough.
What happens if I print it with normal PLA? Will it work? As far as I understood it weights around 700g without electric.
With normal PLA, its weight will increase. And the flight time will be shorter. It will also be less stable. But it will still fly.
@@Kendin-Yap approximately can you jjust give us an insight of Flight Time using LW PLA and normal PLA
Great design man really cool 👍
HI i have question i might travel to turkey and wanted to fly rc airplanes there do u have any ideas what is required for license to get to fly there also the shops i can buy parts from if u can plz inform me also promodel donst have much of parts if u can tell me about more shops ty!!
Thumbs up!!!!
Can you share your printing profile or printing settings? it looks really good!!
I used the S3D (Simplify3D) settings shared by the designer. I just changed the stream value. Flow value for body parts: 53 , for wing parts 54
Didi you use the pre sliced Gcodes??
Merhaba, bir sorum var, türkiye'ye seyahat edebilirim ve rc uçakları uçurmak istedim orada herhangi bir fikriniz var mı oraya uçmak için lisans için ne gerekiyor ayrıca parça satın alabileceğim dükkanlar eğer yapabilirseniz lütfen beni bilgilendirin ayrıca promodel çok fazla bir şey yok Bana daha fazla mağaza hakkında bilgi verebilirseniz, parçaların!
perfect!
Hi, quite new to rc and doing this for a school club. How did you connect/pair the remote to the controller system? Is there a general guide to do so? thanks.
This is not the same for every brand, but in general matching the transmitter and receiver is a simple procedure. Search with the word "BINDING" for the brand and model you are using. You can find many resources.
Normal PLA kullanınca ağırlık artacağından dolayı daha farklı bir batarya kullanılabilir mi? Ne olabilir?
When we use normal PLA instead of LW PLA, is it better to use different battery? What it could be?
Daha düşük kapasiteli bir lipo olabilir. Normalde maksimum 1300mah kullanılabilir. 1000mah kullanabilirsiniz. Bir miktar da hafiftir.
Merhabalar yorumunuzda da bahsettiğiniz gibi normal pla ile uçağı basmayı denediyseniz biraz bilgi verebilir misiniz ? Uçağın kalkışta yaşadığı sorunlar oldu mu veya daha hafif hale getirebilmek için izlediğiniz yollar oldu mu oldu ise bahsedebilir misiniz ? Şimdiden teşekkürler.
@@MehmetEmirŞahin-1 Bu modeli normal pla ile basmadım. Mecbur kalmadıkça bu kadar küçük modeller için pla kullanılmamalı. LW-pla ya göre ağırlık dezavantajları önemli çünkü. 130-150cm kanat açıklığı olan modellerde normal pla kullanıyorum. Örneğin planeprint firmasının Tucano modeli gibi. Sorunsuz baskı ve güzel uçuş sağlıyor. Ama küçük modeller için ideal değil.
Mükemmel
KendinYap great video, and thank you for sharing your 'skill'.
Can you please explain why you choose to use diferent motor 2212 (recomended is 2830)?
In 'coments' someone ask you if he can use 3s 1300mah battery, you say no, but in manual recomended battery is 3s 1300mah?
I am guesing, but, this is why you must use 30g of 'ballast' to get a right cg.?
Thanks.. The recommended 2830 is the same motor as the 2212 I am using. Why? :)
Motor manufacturers use two different standards. Some brands use the outer body diameter of the motor, some brands use the inner rotor diameter. The value 22 is the rotor diameter inside. The value of 28 is the outer casing diameter of the motor. The outer body diameter of 2212 is also 28. Most of the big and high quality brands identify with rotor dimensions. The most accurate description is the rotor dimensions. The other is misleading. The technical values of the Emax XA2212 I use and the recommended motor are similar.
Why I used 1000mah battery. The problem is not about weight. Dimensions are a problem.. The nose area of this model is very small. It is impractical for me to insert and remove the 1300mah battery.
@@Kendin-Yap thank you for 'clearing' that out. Great. Thumb up ;)
I really don't wanna to 'mess' with you, your choice, Emax XA2212 is the 'best' motor for Piper CUB?
And in your 'raw' video of flight with Piper CUB your flight time was cca 4.30 min? That is max flight time on 1000mah 3s battery, or you just get bored ;) ?
can i print with normal pla?
If I print this plane of ABS will it fly??? The thing is my printer cannot print PLA.
Super job, please tell me what program you used to do g code. I see you have a Prusa printer. I am adding you to my favorite channels.
Thanks. I use Prusa slicer and Cura. But I mostly use Prusa slicer.
Yine harika bir proje 👍
What's your settings? I've also printed the model using eSun LW-PLA but the stringing is crazy.
Settings vary by machine. You should use the settings that the designer posted on his site to get started and find the appropriate settings for your particular machine with a bit of trial and error.
Hi great build! For the 1mm steel rod at 2:23, how long of a push-rod is needed? Is 300mm enough? Thanks!
Thanks.. About 520-540 mm
@@Kendin-Yap nooo! I just bought 500m rods :/
Awesome build! did you print the ESUN LW-PLA parts with the 3Dlabprint provided Gcodes or did you reslice for the ESUN filament? Thanks!
In general, I used the settings specified by 3Dlab. I made minor changes to the nozzle temperature and flow settings. You may need to adjust these two depending on the filament brand you use and your 3D printer.
@@Kendin-Yap hey can we use normal PLA instead of LW PLA
servonun ucundaki telin boyunu ayarlamak için kullandığunuz setiskurlu şeyin adı nedir nerden alabilirim
Using PLA as a joint instead of carbon fiber seems like a decision that may come back to bite you later. It’s just not resistant to much force. Why not carbon fiber or steel rod?
harika...
Bonjour et bravo pour cette vidéo très instructive peut tu me dire ou trouver la fermeture du capot merci d'avance Amicalement
Mantap om
What spray paint do you use???
Acrylic spray paint
@@Kendin-Yap thanks
Clever hinging...
Can you use a soldering iron to connect the parts together?
elinize kolunuza sağlık bu model uçağı satarmısınız kumanda hariç?
Great build, just how did you print this, can you share your printer settings, and how do you print without stringing? Thanks
You can’t print lw-pla without stringing which is why all these 3D printed plane companies use as little travel as possible. He probably just used the g-code that comes with it. I’m going to start printing this tomorrow and the only change I’m making for the ended 3 pro is the retraction in the g-code.
@@polar1991 I was able to get great results with PRUSA Slicer, worked much better than CURA, just one last question do you print this plane wall width with 0.4 or 0.8 wall width? 0.4 seems to thin for me.
@@arrie1978 I haven’t figured that out yet. There is a guy named Troy McMillan which has a channel that is all about 3D printed rc planes and he has a video on the best settings for lw pla planes. Hope this helps
would ender 3 be okay for that?
Definitely. Among the files there are ready-made G-code files. These files are for Ender 3.
Hallo, was hälts Du von dem Sender-Empfänger "Flysky i6x"? MfG Ronald
Would it be a problem printing this in Pla+, weightwise? I have some yellow Pla+ laying around you see🙂
Printed parts will be approximately 40% heavier. That's a little too much for a small plane. It does not prevent it from flying. But Stall speed will increase.
Abi iki ucu açık olacak şekilde nasıl baskı alıyorsun içindeki hazır g kodlarıyla da sağlıklı baskı almak mümkün değil
Being that I live in a 5th wheel, don't have space for 3d printer, do you sell the printed parts for people to build their own planes. I understand I will need to get al the extra stuff to make if fly
I'm not trading. There are companies that provide 3D printing services. You can research them.
Reis acaba ejderha tarzı bir uçak yapar mısın ?
kanatlarin nasil baglandigini gostermemeissiniz lastikli yeri
Bravo bro
Normal pla ile yaklaşık 700gr civarında bir ağırlık çıkıyor sizce sorun olur mu?
Ben de normal pla ile basıyorum. Yuzde kac dolgu ile bu agirliga ulasiyorsunuz? Eger ucarsa , agirligun hareket kabiliyeti ve havada kalma suresini etkileyecegini dusunuyorum.
What did you use to design it?
This model is not my design. But Fusion360 is generally used for model aircraft design. Some also use Onshape.
ok thanks@@Kendin-Yap
Merhaba projeniz çok hoşuma gitti bende yapmak istiyorum bir sorum olacak LW PLA yerine normal PLA kullansak bir sıkıntı olur mü?
Bu model LW-PLA için tasarlanmıştır. Normal PLA ile aşırı ağır olur
@@Kendin-Yap teşekkürler
@@Kendin-Yap Açıklama bölümüne normal PLA ile basılabilirsiniz demişsiniz
@@ahmetinanc9534 Tasarımcının beyanı o şekilde olduğu için not olarak yazdım. Ama modeli orjinalde LW için tasarlamışlar. PLA ile basıldığında ekstra ağırlık modelin uçuşunu olumsuz etkiliyor. Minumum tutunma hızı artıyor. Uçuş süresi azalıyor vs. O yüzden ben tavsiye etmiyorum. Ama yine de siz bilirsiniz.
@@Kendin-Yap o zaman LW PLA ile yapalım ilginiz için teşekkürler
Tolles Video, sehr gut gemacht! Danke! Ist es möglich, dass Sie hier Ihre Druckparameter für das eSun LW/PLA zur Verfügung stellen? Das wäre großartig! Danke!
That's the way you do it ...
merhaba , daha önceki kartondan yaptığınız uçakta motoru 3derece açı ile yapıştırmıştınız bu modelde de açı vermek gerekiyor mu
Tasarımında var aslında ama motor yatağını yapıştırırken yine de biraz dikkat edin. Esnediği için açı kaybolabiliyor. Açı olması gerek.
@@Kendin-Yap anladım, ozaman kanat uçlarından ve gövde den simetri alarak 3 dereceyi belirleyip öyle yapıştırayım. Cevabınız için teşekkürler.
Any rc plane require to check air directions .. please tell me
I have a Bambu Labs printer using Bambu Studio, which isn't recognizing the interior geometry of most of the parts. Just the external geometry. Fuselage #1 printed just fine. Everything after that has been a bust.
The bamboo silcer is very new. I don't think it has some of the print settings needed for airplanes. Designers will probably make improvements on this issue in the future. Prusa silicer also did not support this a few years ago.
how many minutes does the battery last?
about 8-12 minutes
What’s the size of your decal?
Did you print this in Vase mode or Normal?