Mr Bayne, I'm an amateur sawdust generator and just started back into woodworking after not being in it for over 50 years (high school). Just building for fun, not commercially. But your tip on how to apply Polyurethane by thinning it and wiping has worked WONDERFUULY! No brush marks, beautiful finish and very easy. It takes more time and coats but the results are amazing. Thank you!
Thanks for the informative video. I have been using a very similar technique for the last twenty-five years, also with excellent results. I start with a coat of gloss poly/thinner. If you add the second coat at around four hours, you don't have to sand. I start with three coats, then let it dry overnight. I lightly sand with 0000 Liberon steel wool then add another three coats of gloss poly/thinner. I let the project dry overnight, then lightly sand again. Finally, I add a topcoat of satin poly/thinner. I find I get better depth of clarity by just using the satin poly for the last coat.
Thanks for sharing your technique. If I understand correctly you also always use poly + thinner and not straight poly. Am I right? Also, will you please elaborate on the mixing ratios for poly + thinner? Or are they same as Roger's? Thanks - learning a lot from these videos and comments from experienced people like you and Roger.
@@ashokmoghe8035 You can cut the poly 50:50 with thinner (I like mineral spirits like Bayne does). You don’t have to change the ratio. The commercial wipe-on poly is just polyurethane diluted with thinner. I have also just brush coated with General Finishes Poly (undiluted) then rubbed it out fast to keep it from building up. That takes more skill, and you have to move fast. The bottom line is that poly is hard to keep from looking like you covered your masterpiece in plastic wrap if you don’t keep the layers very thin. Hope this helps.
Thanks so much for this video! I have always struggled with finish. I have a live edge project that I'm getting ready to finish, and I will try this method.
@@tomhill4003 Hello Tom, thank you for finding the video. I have had great success finishing live edge with this process. Have fun and let me know how it works out.
Just finished a kitchen table with a brush and wish I had seen your video sooner. Definitely going to try your technique next time as I do have some brush strokes in my final coat. Appreciate you taking time to share your tips.
@@BayneCustomWoodworking I couldn't stand it so I sanded down the table with 220 and used your technique and WOW...what a difference...EXACTLY what I was looking for. I don't think I'll ever pick up a brush again. Again thanks for taking time to share your experience with the rest of us.
Your video is worth every minute, thanks for taking your time to explain everything, I’ve used water polyurethane on most of my projects just because of how hard it is to get a smooth finish with oil polyurethane.
Nice tips... I'm going to give this a try. I like that the extra thinned coats get to absorb into the wood and adhere better than the standard non-thinned poly. Tx!
@@BayneCustomWoodworking Question... I know you probably exclusively use oil based poly, but I wonder if the same can be done with Polycrylic by adding water to it in the same way... knowing I might have a bit more sanding between coats due to the possible grain raise it may cause with those first couple coats.
@csimet I understand you can add water but I would check with the manufacturer. To avoid the grain pop, After sanding you can water pop it first by gently spraying water on it, let it dray and resend it. Water popping works well
What I had always wanted to learn, excellent video, no one had ever explained it better, my eyes opened, I always left marks with the brushes, now I will test your teaching, thank you very much, I hope many will see this video. since it only has few subscribers, but you. he is a very good teacher
Now this is the type of news I like to get. I am glad the process has worked out for you. Something that is not in the original post is that after the final coat has had time to dry, usually about 72 hours, I use a brown paper bag to lightly sand. It acts like 2000 grit sandpaper. give it a try
Finally. 🙌 Your suggestions have saved my project from h-e-double-hockey-sticks. 😭 I had actually made a wipe on poly (without realizing it) - but was using my very expensive, high quality finish brush to apply - and no matter what I did - my initially perfect finish would start to bubble (about 20 min after applying). I was stumped. I tried 4 different kinds of brushes. I tried the finish right out of the can, without thinning.. I tried everything... it was a nightmare! NOTHING produced a clean finish. I was taking all steps.. not missing a beat. So I went back to my thinned poly (using Varathane brand, which I'll likely never use again)... cut up an old cotton t-shirt... and wow... went on like a dream... and so far, it is drying bubble free - as well as brush mark free (wasn't having problems with brush marks, tho - just bubbling). I think I am finally done!!! Hallelujah :)
@@BayneCustomWoodworking thank you sir, I may try a lint free micro fibre on a coat , I'll let you know how it works , got a whole load of live edge wood this fall, I'm going to make some floating shelves and window ledges
Thank you for this video! I have always struggled with the streaks, bubbles, and tedious process in general. I want to try this on my current project. I don’t like the yellowing over time caused by regular polyurethane. Do you happen to know if this process will work just as well with water-based?
Oh, I just read through the comments and see that it is not possible to use water-based polyurethane with mineral spirits, but that water (instead of mineral spirits) would work to thin water-based poly. In my experience regular poly is more durable, but I’m using a white wash stain and really don’t want it to yellow over time.
Interesting dilemma- I can’t say that I have ever waited more than 24 hours between coats. But because it’s so easy to apply coats, when I used to work full time I would take 10 minutes to apply a coat before I left for work each day. Not sure if that is possible for you.
I followed the instructions to the lett and the results were absolutely fabulous. I now must refinish two table leaves in a similar fashion. How long can I keep the misture from the final four coats to be used on the leaves?
Fabulous, I have used this on multiple walnut projects. am using it on a walnut table project I just picked up. I do not stain walnut. I sand it up to 600 grit to bring out the grain and poly it.
So, have you ever added a stain to your mixture? Doing a wrought iron bench with wooden slats on the seat and a wood border on the back. Driving myself nuts with a brush that creates bubbles for a rough finish.
Thanks for the great video. I have a piece of stained wood with sanding scratches in it. I was too aggressive with my 150 grit and the stain didn't help hide the scratches. Will this poly solution help to fill in my scratches?
Unfortunately poly will not fill scratches. I have had this happen where I didn’t see the scratches until after staining. Normally I would sand up to 180 grit and that eliminates most scratches left by higher grit.
@@BayneCustomWoodworking Thanks so much for the fast reply. I just tried stepping up the grits, I went from 180 to 220 to 400. Maybe I shouldn't have skipped the 300 grit, because the scratches are a little better, but still there. What about wet-sanding? Can I do that on something that has oil stain? The stain is cured.
Usually between the last 3 coats. I have gone to using 400 or 600 grit. Then I have started to use brown paper after everything is dry. It works like 2000 grit sand paper and gives it a nice smooth finish.
Brilliant! I will try this. Where did you get your little supports for the table top? Why did Minwax tell me just two days ago that they don't recommend ever thinning their poly?
Have been going through the comments to find out the sanding process between coats. I noticed you have recently gone away from using 0000 wool. I agree with that move but are you using 400g or 600g now? Between which coats. Great video by the way, loved the info and straight to the point. Great value from this i had to subscribe
I appreciate you subscribing and for the compliment on the video. You are right that I have moved away from steel wool and into 400 or 600 grit. It really depends on the materials and how each previous coat went on. Another caveat that I can add is that when completely dry and before delivery to clients I am also using brown paper to give that final smoothness. It’s almost like using 2000 grit sand paper.
Thank you very much for your time Sr, you have a very generous heart, teaching us How to do things right, much appreciated, I have two dressers to finish, and I did not know what to decide, Water base or oil finish, my decision is to finish the drawers water base, the rest I will follow your videos to the letter, God Bless you always, best regards form Mexico
Thank you for this fabulous video. I've always struggled with brushing on a finish and this information really resonates with me in solving my problems. I was wondering however, how many coats would you put onto a bamboo countertop? Given it's use, would you put on more? Thanks again for the great video!
James, I am glad you found this video and thank you for the kind words. While I have never worked with bamboo, I would think that 6 coats would be sufficient. As I recommend with any table I finish, I would let it let it dry for a good 72 hours after the last coat to make sure it’s cured fully before using it.
@@BayneCustomWoodworking I just finished a test countertop for my bathroom using pine and I am over the top with just how well this works. Looks good! Feels great! Thanks again!
Thank you! This was so easy to do when I finished a floating shelf last year. I used an oil-based finish like you did in the video but now, on another project, I might need to use water based poly - would the same thinning ratios apply here with water? 1 part water-based poly: 2 parts water for the first couple of coats and then flip the ratio for the final few?
Would this method work well with red oak? Will increasing the number of coats applied correspondingly darken the hue of the oak? I’m a complete novice and looking for the best approach at finishing a new raw wood banister. Thanks for posting such an excellent easy to follow video.
This is a clear finish so it won’t really darken the hue. It will enhance it however. More coats might protect it a bit more but won’t change the color. If you are looking to darken the hue a bit consider staining it with minwax red oak oil stain first. I did this on a red oak table and it looks great.
Thank you. I have only used grain filler or sanding sealer prior to staining. I have never seen the need to use it prior to applying poly but it doesn’t mean it can’t be used.
Amateur here.... Will this process work the same with Spar Urethane ? The utility table I'd use it on won't stay outside but I may need it outdoors for a few hours once in awhile. Thanks
I have never tried this with spar finish, but have moved to using teak oil for anything that will be outside. One or two coats depending on the brand and you are done.
In my country (Cyprus) I cannot find minwax fast drying polyurethane... I can find two part clear polyurethane though... What do I do in that case to make wipe poly? Is it possible to use poly without hardener and mix with mineral spirit as the video?
Thank you so much for taking the time to do a detailed video that thoroughly covers this finishing method. You have made a believer out of me. I will soon be trying this method on a table I am currently building for my boat.
@@BayneCustomWoodworking I have had to alter the protocol a bit. My table had a cedar coloured stain (to match my boat) and the rag method began to lift the stain (probably due to the high solvent content). So I'm going the give the stain another day to dry and then brush the first sealer coat. Once that coat covers the stain, I can return to the rag method.
Great video, thank you for this method, looks so much better than brushing. I have a table top that goes in almost a sun ray grain and then a frame of grain going around the perimeter, very hard to describe but it's difficult to follow the wood grain, when wiping on, does it have to be applied with the wood grain? Since there's no brush marks, I'm hoping it's not as important and tedious.
Thank you -- No its not an issue because the mineral spirits work as a leveling agent. Go with the grain as much as possible, but don't sweat it if you can't -- Have fun and enjoy
Hi. I used this technique to finish a table and it turned out beautifully. I used semi-gloss polyurethane but find it a bit too shiny and harsh. My question is, can I use this same technique using satin finish over the semi gloss, using the 2-1 ratio of 2 parts mineral spirits to 1 part minwax and then following up with the 2 parts minwax to 1 part mineral spirits, or can I skip either the first or second mixture since the table has the minwax finish on already. After lightly sanding the existing semi-gloss finish with a fine grade sandpaper of course. I'm not sure if either mixture can be skipped. Your mixture is the best I've found for professional grade finishing. Thanks
I am glad you found this helpful and I appreciate the compliments at the end. There is no need to start over, just mix 1 part mineral spirits and 2 parts satin and apply 2 coats. That should take away the shine and not hurt anything.
Awesome video thanks! FYI minwax tech support recommends only 100% Spirts not the odorless kind. according to them it could make it more foggy. or affect clarity.
Thank you. I have never seen a cloudy or foggy look in 20 years. Now they do make another kind that is milky as you pour it. I would never use that. Thanks for the information
This is outstanding! I plan on using this method to restore an antique drop leaf dining table. I made the mistake of putting walrus oil on one of the legs (just starting finishing ), but then I saw your video. I would like to know if you can use your method over the top of the walrus oil, or how do it get the table leg ready for your process? Thanks for the formula though!!!
Thank you for the compliment. While I am A huge fan of Walrus oil, I would remove the oil before applying my poly solution. Now I say that because I have never put it over oil before. I might recommend that you email Walrus oil and ask them as well.
A good instructional video, thanks for posting this. I’m getting ready to finish a birch butcher block tabletop for use on a portable basement workbench. I was looking at using the wipeable oil based product, but decided now to mix my own using oil based polyurethane and mineral spirits with your application process. I’m new to wood finishing, and this project will also serve as a test run for finishing a future countertop on cabinets I will install along a wide hallway on my main floor. Question: I’m going unstained for this initial project, but in my hallway I’d like to do something that will show slightly more grain. I think it is going to be difficult (or very expensive) to find a hardwood countertop (˜112”) with good graining for the hallway countertop, but I can get birch butcher block up to 120” long from big box stores. Do you have any suggestions for staining birch butcher block to enhance the grain slightly, but not overly darken the wood? Most stain application videos I’ve reviewed seem darker than I’d prefer. I do have a couple foot section of extra butcher block left over from the current basement project that I can use for experimentation. Thanks again for the instruction on the poly application and any staining suggestions!
Thank you for watching and for the compliments. As for stain I only use Minwax oil stain. Good choices would be Special Oak, Golden Oak and Puritan Pine are nice light stains. If you don't mind a little red then Gun Stock and Red Oak are nice as well. I would also suggest that you use Minwax conditioner prior to staining to get an even stain.
Oh my goodness! I am so glad that I searched and found your channel! My daughters mistakenly wasted fingernail polish remover on my table!😢😢 I’ve successfully, due to this video, sanded, restained and added polyurethane to my table and it’s as good as new- thanks to you!!😅😅😊
YIKES! Having children and grandchildren I understand how these things happen. This is the type of success story I like to start the week with! I am glad it worked out for you.
Exactly in the same situation. I accidentally spilled nail polish remover on our new table and ruined the finish. I have hope now. What stain did you use? Thanks.
I’ve loved Minwax’s wipe on poly, I’ve used it exclusively for a decade. I always suspected it was merely a thinned version of their usual oil based poly. You’ve given a good recipe for a make your own version. Definitely cheaper than buying a wipe on poly.
@@BayneCustomWoodworking I’m finishing a piece of wooden wall art so durability isn’t a concern. I’m just looking for a finish that won’t have a strong odor (trapping the odor of the wood stain if possible) and will keep the wood in a natural/unfinished/satin look
@@anthonydiecidue7916 I have always found that stain has more of an odor than the poly that I make. I actually finish projects inside my house without an issue. But if you have concerns then water based is your best answer.
Sir; Thanks. will try this technique. Had to strip three time. Used Tung Oil Finish which cured very rough. First attempt was with Poly which developed bibbles. redoing my Coffee Table that we bought 25 years ago from Ethan Allen.
Binoy I am glad you found the post and hope you a able to use it to complete your project. Just make sure all the old finish is removed before applying.
What a great video. Thank you for these very useful explanations. I just had 30 years old pine kitchen cabinets repainted with Farrow and Ball modern eggshell emulsion (water-based). And the kitchen worktops will follow. Should or could I use solvent-based marine polyurethane on them or would standard polyurethane be sufficient. The house is shared with tenants and worktops take a hard beating and need to be easy to clean.
Thank you for the appreciation. Honestly I think you need to talk to counter top professionals before preceding. I know the finish I use will always hold up on table tops. But counter tops take quite a beating. I have used straight floor poly on desktops for soft wood and it’s held up well. But again, counter tops take a beating on a daily basis.
In spite of the video edits being faffed up, that's not the point of this video (or channel) and I'm liking your explanations and methods. I'm brand new to polyurethane and I'm practicing on a couple pine slabs. Pretty excited to keep learning more and getting better at it!
Any good cotton cloth will do. I just find that old white t-shirts work the best. I am actually looking at purchasing some cotton cleaning cloths to try.
Thank you for the video. Followed your advise and My table top finish turned out much better. However, I see some patches are showing up dull. Is there a quick fix so that I can get an even shine?
Mohib I am glad it worked out for you. I am not sure why you would have dull spots unless they were sanded differently. Was this fresh wood at the start or was this a refinish project?
Thank you so much for this demo. Does this mix work well over paint as well? Also is it possible with water based poly? I would prefer if the paint didn’t yellow. Thanks!
Because this is an oil base poly it will not work with water base. I have never put it over paint. Honestly when I need to protect paint I use a spray acrylic from lowes or home depot. I use this on all my grandchildrens toys that I make them when the finish is paint. The odor is quite harsh but after a couple of days it’s gone and some do their toys are years old and have held up well.
I see your Video too late. I used exact same polyurethane with a brush on first coat. If I sand, then apply your method on the next coats, two parts urethane and one part paint thinner with a rag, will this improve my next topcoats? Thanks for your video!!!
Leonard - Yes but if there are brush marks, try to sand them out but gently. The next coats should apply nicely. Just keep them thin is all. let me know how it comes out
No brush marks as I have been painting for years (@ 67) but not much experience in polyurethane on wood. There are however a ton of tiny bumps. I imagine they are tiny air bubbles that will sand out with a light sanding (320 grit). Thanks for your response. You are truly amazing ie; response, dedication to your gift. Thanks!
Bayne just wanted to follow up. I sanded down the original brush coat to get rid of pin head size bumps/bubbles? And used your wipe on method. Since I already had a coating I went with 50/50 twice to level everything out. Then I did your 2 to 1 , (urethane being 2, paint thinner 1)and it worked out perfect. Thanks for your expertise and excellent communication and integrity.
@@BayneCustomWoodworking its 1 1/2" tongue and groove pine that I sanded to 120 and whitewashed for a counter top. I want to seal it and protect it with something durable enough for everyday kitchen use.
James , I would look at butcher block oil from Walrus oil. It’s similar to the product that I use on all my cutting boards and protects the wood very well. It will certainly be safe for your pregnant wife as well. walrusoil.com/collections/wood-finishes They are very responsive to emails
Will this method work with minwax spar urethane? Or does it have to say "wiping urethane" on the container? I've never stained anything before this month and working on a raw birch pantry currently.
I only use spar finish for outside/exterior projects and never wipe that on. I am sure you could use this method but not sure why you would use spar finish on an interior project. That said this process is making wiping poly so the container will not say wiping polyurethane on it. I hope this helps
@@BayneCustomWoodworking thanks! What type of brush would you use then? I've seen so many different answers online when searching for info and that is the finish the person at Sherwin Williams recommended for a polyurethane when I asked and told them what it was for. Their color/stain match is amazing, but the people checking me out must have been new. One person had zero clue and the other acted more knowledgeable, but I think it was just a show 🙄 it's been frustrating to say the least, I can't wait until this is done. I will leave the large projects for the pros! 🤣 Might try smaller ones for fun.
@@BayneCustomWoodworking yes a kitchen pantry, which is right by a door to outside so that may be the reason they recommended this finish. It's minwax indoor/outdoor helmsman spar urethane that they recommended. And Zar interior oil base multi-surface stain. I was wanting to do a verethane poly+stain but couldn't find anything close enough to match colorwise.
I would buy the best soft bristle Purdy brush at Lowes or Home Depot. I normally wait 3 days to apply poly after staining, but I tend to be over protective of my projects. Apply light coats brushing with the grain as much as possible. I lightly sand with 400 or 600 grit sand paper between coats and make sure to brush off the residue before applying next coat. With spar finish you could probably get away with 3 coats. Let it dry a day or 2 and the use a brown paper bag to final sand. That works like 2000 grit sand paper and will remove any bumps the poly may leave. This will be great when you are finished. Take your time and enjoy the process.
Hello Roger, this is a very good, no-nonsense, full of information video. I watched it multiple times and saved it in my reference videos. One question - if I have water based polyurethane can I use same method by substituting water for mineral spirits? In California it is tougher to find regular polyurethane these days. Thanks and looking forward to more content from you.
@BayneCustomWoodworking l used your 2 to 1 ratio ( as for your polyurethane). Sticky 48hrs later, handled w/0000 steel wool. It's a pine carpenter's table from the hardware store. I don't know if this poor table will survive me!
@@NaNana-ey6jk I would sand it off and either use straight Tung oil applied lightly, let sit for 15-20 minutes and wipe it off. Then let it dry. Or re sand and start over with poly mix. You got this
Hello Roger. I was attempting my first stain project and was having difficulty applying a clean poly clear until I found this video. THANK YOU for saving my sanity! Beautiful solution for me. THANK YOU THANK YOU THANK YOU
I just looking for a video of me spraying some chairs and I am not sure we have ever created one. I will have to get one recorded soon. Are their questions I can answer for you?
We made a wipe on solution and wiped it on with a cotton rag to finish some red oak doors we stained. It seems to streak…. Like some parts were dull from the mineral spirits and then we had shiny streaks from the polyurethane. We stirred the solution often too. Does wiping it on with a circular motion alleviate these streaks?
Thank you for sharing this with us. Very informative. I have been trying to decide the best finish for a black walnut “waterfall” table which is 18” on one end and 27” on the crotch end. I initially considered epoxy, but that would make many runs on the waterfall end. Also, I’m leaving the bark on the live edge, albeit after sanding about 1/2 off so it doesn’t catch on pants legs, etc. This method should allow me to use this on the edges so it can “soak” in providing a smooth finish. Again, many thanks!!
I normally do not work with a water-based polyurethane but if I do I would use general finishes high performance water base. They state on their product that you can thin it with distilled water at about 5% up to about 10% I've never tried it but they look like they can. but I'm always a fan if I'm going to put water-based on I'm going to put it on with a good high quality roller or spray it or even a good high quality foam brush but again I don't use water base very often
Thanks. I actually used rub on gloss poly on a Tenor Ukelele I had built. I do wish I had seen this first because a 2 part thinner to 1 part poly as the first two coats where the thinner mix helps level is a great idea
@@BayneCustomWoodworking the project took 7 weeks of about 3 to 4 hours a day 5 to 6 days a week to get to the apply finish stage, but it was entirely scratch built including cutting the thin strips that were glued up to form the top and back plus all the jigs and molds needed. But it has been so much fun that I have another Tenor Uke a bit over 1/3 built in the works plus I ordered a guitar kit from Stewmac. Actually the guitar kit will be a lot easier because a lot of work has been done by the supplier. Until this, the biggest project I completed was a 15 by 20 foot summer Cabana that took 800 hours to complete. The first Uke will have about 200 hours into it, but considering square feet of build it easily is the longest project ever for me. I think any one that has a bandsaw and a way to achieve thickness sanding plus a bit of patience can build a stringed instrument. The kits can save a large amount of time. Stewmac is great for quality I've heard but pretty pricey unless like me you buy a once in a blue moon sale. Maderas Barber in Spain seems to have nice kits at very reasonable prices but if you have the two tools I indicated you spend very little especially if you buy rough cut and plane with even a small electric hand planer which is what I used. It is actually a favorite tool and only cost $45 at Harbor Freight. My thickness sanding could be easier but it works and I use a 6 by 48 belt sander attached to my Shopsmith. The bending I achieved with steam. Matthias Wandel used a rice cooker, others use a wallpaper steamer. I used an electric skillet with lid plus I would thoroughly wet the side piece and use a steam iron on it too. It worked really well. What is really cool is whether guitar or Ukelele you have an instrument that with a soundboard made of Red Spruce or Cedar or Redwood as I used and an all solid wood construction that will rival a Martin or Santa Cruz or Taylor instrument that can cost easily $10,000 for probably in the neighborhood of $100 and the difference in sound between your solid top and a laminate top is like Am transistor pocket radio to top notch stereo system. I really would encourage anyone to give building a stringed instrument a go. It's too much fun and too much reward to let it pass if you have tools that are sufficient for the job at hand. Take care, Like your channel, glad TH-cam recommended it to me...
Does this work with water base semi-gloss same brand, I restore vintage travel trailers mostly birtch 4'x8' panels brushes and rollers don't work well, spraying is better but dries in the gun to fast, thank you.
This video changed my life with using poly. Thanks a lot!
I am glad it help
Haven't went back to a brush/foam brush since wipe on in a few seconds to a few minutes time saving no drips or brush marks thank you
I am right there with you on that. Cheers!
Mr Bayne, I'm an amateur sawdust generator and just started back into woodworking after not being in it for over 50 years (high school). Just building for fun, not commercially. But your tip on how to apply Polyurethane by thinning it and wiping has worked WONDERFUULY! No brush marks, beautiful finish and very easy. It takes more time and coats but the results are amazing. Thank you!
Welcome back! I appreciate you finding my post and for working the solution.
I use a staining sponge, And three twenty grit sandpaper, I like the way you thin down the polly thank you for sharing.
By for now ken
I have been making my own linspeed and wiping varnishes for years but this regimen makes sense so I will follow your lead in the future. Thank you.
I hope it works out for you as it as for me.
Thanks for the informative video. I have been using a very similar technique for the last twenty-five years, also with excellent results. I start with a coat of gloss poly/thinner. If you add the second coat at around four hours, you don't have to sand. I start with three coats, then let it dry overnight. I lightly sand with 0000 Liberon steel wool then add another three coats of gloss poly/thinner. I let the project dry overnight, then lightly sand again. Finally, I add a topcoat of satin poly/thinner. I find I get better depth of clarity by just using the satin poly for the last coat.
Thank you for explaining your process. I will have to give this a try.
Thanks for sharing your technique. If I understand correctly you also always use poly + thinner and not straight poly. Am I right?
Also, will you please elaborate on the mixing ratios for poly + thinner? Or are they same as Roger's?
Thanks - learning a lot from these videos and comments from experienced people like you and Roger.
@@ashokmoghe8035 yes that is correct
@@ashokmoghe8035 You can cut the poly 50:50 with thinner (I like mineral spirits like Bayne does). You don’t have to change the ratio. The commercial wipe-on poly is just polyurethane diluted with thinner. I have also just brush coated with General Finishes Poly (undiluted) then rubbed it out fast to keep it from building up. That takes more skill, and you have to move fast. The bottom line is that poly is hard to keep from looking like you covered your masterpiece in plastic wrap if you don’t keep the layers very thin. Hope this helps.
Thanks so much for this video! I have always struggled with finish. I have a live edge project that I'm getting ready to finish, and I will try this method.
@@tomhill4003 Hello Tom, thank you for finding the video. I have had great success finishing live edge with this process. Have fun and let me know how it works out.
@@BayneCustomWoodworking Will do! It's Monterey pine, which is considered a trash wood, but I'm giving it my best!
@@BayneCustomWoodworking I will!
Just finished a kitchen table with a brush and wish I had seen your video sooner. Definitely going to try your technique next time as I do have some brush strokes in my final coat. Appreciate you taking time to share your tips.
I am sure your table.looks beautiful but am glad you found the video for future use
@@BayneCustomWoodworking I couldn't stand it so I sanded down the table with 220 and used your technique and WOW...what a difference...EXACTLY what I was looking for. I don't think I'll ever pick up a brush again. Again thanks for taking time to share your experience with the rest of us.
@@timc8913 perfect and you are welcome. Thank you
Your video is worth every minute, thanks for taking your time to explain everything, I’ve used water polyurethane on most of my projects just because of how hard it is to get a smooth finish with oil polyurethane.
You are very welcome. I am glad it helped
Nice tips... I'm going to give this a try. I like that the extra thinned coats get to absorb into the wood and adhere better than the standard non-thinned poly. Tx!
@@csimet Thanks
@@BayneCustomWoodworking Question... I know you probably exclusively use oil based poly, but I wonder if the same can be done with Polycrylic by adding water to it in the same way... knowing I might have a bit more sanding between coats due to the possible grain raise it may cause with those first couple coats.
@csimet I understand you can add water but I would check with the manufacturer. To avoid the grain pop, After sanding you can water pop it first by gently spraying water on it, let it dray and resend it. Water popping works well
What I had always wanted to learn, excellent video, no one had ever explained it better, my eyes opened, I always left marks with the brushes, now I will test your teaching, thank you very much, I hope many will see this video. since it only has few subscribers, but you. he is a very good teacher
Excellent- I am glad this will help. Credit goes to an old shop teacher/Carpenter who taught me years ago
I'm about to try this tomorrow. It's been very frustrating learning woodworking and then to hit a wall at the finish. Literally!
Only on the third coat, our bar already looks amazing!! Thank you!!
Now this is the type of news I like to get. I am glad the process has worked out for you. Something that is not in the original post is that after the final coat has had time to dry, usually about 72 hours, I use a brown paper bag to lightly sand. It acts like 2000 grit sandpaper. give it a try
Finally. 🙌 Your suggestions have saved my project from h-e-double-hockey-sticks. 😭 I had actually made a wipe on poly (without realizing it) - but was using my very expensive, high quality finish brush to apply - and no matter what I did - my initially perfect finish would start to bubble (about 20 min after applying). I was stumped. I tried 4 different kinds of brushes. I tried the finish right out of the can, without thinning.. I tried everything... it was a nightmare! NOTHING produced a clean finish. I was taking all steps.. not missing a beat. So I went back to my thinned poly (using Varathane brand, which I'll likely never use again)... cut up an old cotton t-shirt... and wow... went on like a dream... and so far, it is drying bubble free - as well as brush mark free (wasn't having problems with brush marks, tho - just bubbling). I think I am finally done!!! Hallelujah :)
I am glad you found the post and the process was able to help you safe the project. Nothing like an old cotton t-shirt to save the day.
Great finish, you helped me sir to achieve perfection , I wonder if those micro fibre rags might work good ?
Dale I am glad this worked and helped you achieve your goal. Not should about the micro fiber, have always used cotton
@@BayneCustomWoodworking thank you sir, I may try a lint free micro fibre on a coat , I'll let you know how it works , got a whole load of live edge wood this fall, I'm going to make some floating shelves and window ledges
do you change your rag in between mixtures?
Yes I do
Thank you for this video! I have always struggled with the streaks, bubbles, and tedious process in general. I want to try this on my current project.
I don’t like the yellowing over time caused by regular polyurethane. Do you happen to know if this process will work just as well with water-based?
Oh, I just read through the comments and see that it is not possible to use water-based polyurethane with mineral spirits, but that water (instead of mineral spirits) would work to thin water-based poly. In my experience regular poly is more durable, but I’m using a white wash stain and really don’t want it to yellow over time.
Can only work in shed on my monthly day off. Is it too long between layers?
Interesting dilemma- I can’t say that I have ever waited more than 24 hours between coats. But because it’s so easy to apply coats, when I used to work full time I would take 10 minutes to apply a coat before I left for work each day. Not sure if that is possible for you.
I followed the instructions to the lett and the results were absolutely fabulous. I now must refinish two table leaves in a similar fashion. How long can I keep the misture from the final four coats to be used on the leaves?
I find that after a couple of days the final mixture thickens too much to use.
There is no need to do this method on 2 nightstand tables, right?
That is entirely up to you. I want to protect my builds as much as possible so I do this process on every indoor build.
How do you think this would work on a walnut gun stock?
Fabulous, I have used this on multiple walnut projects. am using it on a walnut table project I just picked up. I do not stain walnut. I sand it up to 600 grit to bring out the grain and poly it.
So, have you ever added a stain to your mixture? Doing a wrought iron bench with wooden slats on the seat and a wood border on the back. Driving myself nuts with a brush that creates bubbles for a rough finish.
I have not. I feel your pain with the bubbles. I would love to see the end product
Thanks for the great video. I have a piece of stained wood with sanding scratches in it. I was too aggressive with my 150 grit and the stain didn't help hide the scratches. Will this poly solution help to fill in my scratches?
Unfortunately poly will not fill scratches. I have had this happen where I didn’t see the scratches until after staining. Normally I would sand up to 180 grit and that eliminates most scratches left by higher grit.
@@BayneCustomWoodworking Thanks so much for the fast reply. I just tried stepping up the grits, I went from 180 to 220 to 400. Maybe I shouldn't have skipped the 300 grit, because the scratches are a little better, but still there. What about wet-sanding? Can I do that on something that has oil stain? The stain is cured.
This is great. Can you do the same thing with Watergate polyurethane
I meant waterbase
I have heard it can be thinned with distilled water but I have never tried it
Do you same between coats?
Usually between the last 3 coats. I have gone to using 400 or 600 grit. Then I have started to use brown paper after everything is dry. It works like 2000 grit sand paper and gives it a nice smooth finish.
Can you stain first then do your system
@@gerryrutar310 Absolutely, I use this over stain on a regular basis. The only thing I do is let the stain fully dry for 3 days before applying poly.
Brilliant! I will try this. Where did you get your little supports for the table top? Why did Minwax tell me just two days ago that they don't recommend ever thinning their poly?
The painter tips I get at Lowes, but Amazon has them as well. In 30 years of doing this with Minwax oil based poly I have never had any issues.
Great video. Can I also do the same process with oil modified poly??
Thank you…The only poly I use is oil based
Looks great. Would this process work on a painted surface on furniture???
You know, I have never tried that. I am sure it would because it works on stain. But I always use spray enamel over paint
I like your technique excellent information thank you for sharing, God bless by for now, Ken
Thank you. I am glad it help. God bless you as well
Have been going through the comments to find out the sanding process between coats. I noticed you have recently gone away from using 0000 wool. I agree with that move but are you using 400g or 600g now? Between which coats. Great video by the way, loved the info and straight to the point. Great value from this i had to subscribe
I appreciate you subscribing and for the compliment on the video. You are right that I have moved away from steel wool and into 400 or 600 grit. It really depends on the materials and how each previous coat went on. Another caveat that I can add is that when completely dry and before delivery to clients I am also using brown paper to give that final smoothness. It’s almost like using 2000 grit sand paper.
Awesome video. I will definitely try your process on my next project. Thank you🤙🏾🤙🏾
@@wahinenuiloa Thank you ….Glad you found the video
Mr. Bayne does this finish self combus?t
Not in my 30 years of using it
Thank you very much for your time Sr, you have a very generous heart, teaching us
How to do things right, much appreciated, I have two dressers to finish, and I did not know what to decide, Water base or oil finish, my decision is to finish the drawers water base, the rest I will follow your videos to the letter, God Bless you always, best regards form Mexico
Thank you for the kind words. Please send me pictures when you are finished
Thank you for this fabulous video. I've always struggled with brushing on a finish and this information really resonates with me in solving my problems. I was wondering however, how many coats would you put onto a bamboo countertop? Given it's use, would you put on more? Thanks again for the great video!
James,
I am glad you found this video and thank you for the kind words. While I have never worked with bamboo, I would think that 6 coats would be sufficient. As I recommend with any table I finish, I would let it let it dry for a good 72 hours after the last coat to make sure it’s cured fully before using it.
@@BayneCustomWoodworking I just finished a test countertop for my bathroom using pine and I am over the top with just how well this works. Looks good! Feels great! Thanks again!
Thank you! This was so easy to do when I finished a floating shelf last year. I used an oil-based finish like you did in the video but now, on another project, I might need to use water based poly - would the same thinning ratios apply here with water? 1 part water-based poly: 2 parts water for the first couple of coats and then flip the ratio for the final few?
I am.glad the process helped on your shelf but I have never used the process on water based.
Thank you! I live in Mexico and haven't been able to find Wipe on poly so you saved my life!
I am glad I was able to help. Good luck
Would this method work well with red oak? Will increasing the number of coats applied correspondingly darken the hue of the oak? I’m a complete novice and looking for the best approach at finishing a new raw wood banister. Thanks for posting such an excellent easy to follow video.
This is a clear finish so it won’t really darken the hue. It will enhance it however. More coats might protect it a bit more but won’t change the color. If you are looking to darken the hue a bit consider staining it with minwax red oak oil stain first. I did this on a red oak table and it looks great.
What about course grain do you us a grain filler then wipe your finish on. Great video
Thank you. I have only used grain filler or sanding sealer prior to staining. I have never seen the need to use it prior to applying poly but it doesn’t mean it can’t be used.
Great explanation with right amount of details, just what I need at the moment. Thanks a ton sir.
Thank you. I am glad you found it.
Amateur here.... Will this process work the same with Spar Urethane ? The utility table I'd use it on won't stay outside but I may need it outdoors for a few hours once in awhile. Thanks
I have never tried this with spar finish, but have moved to using teak oil for anything that will be outside. One or two coats depending on the brand and you are done.
In my country (Cyprus) I cannot find minwax fast drying polyurethane... I can find two part clear polyurethane though... What do I do in that case to make wipe poly? Is it possible to use poly without hardener and mix with mineral spirit as the video?
What brand of poly can you purchase. I only use minwax because I prefer it. Any oil based poly would work
Thank you so much for taking the time to do a detailed video that thoroughly covers this finishing method. You have made a believer out of me. I will soon be trying this method on a table I am currently building for my boat.
Brian
Thank you for the kind words. please let me know how your table comes out
@@BayneCustomWoodworking I have had to alter the protocol a bit. My table had a cedar coloured stain (to match my boat) and the rag method began to lift the stain (probably due to the high solvent content). So I'm going the give the stain another day to dry and then brush the first sealer coat. Once that coat covers the stain, I can return to the rag method.
I have had to let the stain dry for about 72 hours to make sure it doesn’t lift too much stain off. That way I am certain it’s completely dry
Very informative. Thank you for the information.
Thank you
Can I use this to apply over paper pictures attached to the surface of the wood getting the same coat
I have no experience putting this on paper. My guess is that it would eat up the paper or ruin the picture
Great video, thank you for this method, looks so much better than brushing. I have a table top that goes in almost a sun ray grain and then a frame of grain going around the perimeter, very hard to describe but it's difficult to follow the wood grain, when wiping on, does it have to be applied with the wood grain? Since there's no brush marks, I'm hoping it's not as important and tedious.
Thank you -- No its not an issue because the mineral spirits work as a leveling agent. Go with the grain as much as possible, but don't sweat it if you can't -- Have fun and enjoy
@@BayneCustomWoodworking
Thank you
Thank you for all the wonderful information people should really listen to you.
Thank you and you are welcome
Hi. I used this technique to finish a table and it turned out beautifully. I used semi-gloss polyurethane but find it a bit too shiny and harsh. My question is, can I use this same technique using satin finish over the semi gloss, using the 2-1 ratio of 2 parts mineral spirits to 1 part minwax and then following up with the 2 parts minwax to 1 part mineral spirits, or can I skip either the first or second mixture since the table has the minwax finish on already. After lightly sanding the existing semi-gloss finish with a fine grade sandpaper of course. I'm not sure if either mixture can be skipped. Your mixture is the best I've found for professional grade finishing. Thanks
I am glad you found this helpful and I appreciate the compliments at the end. There is no need to start over, just mix 1 part mineral spirits and 2 parts satin and apply 2 coats. That should take away the shine and not hurt anything.
It would have been nice to see a close-up of the surfaces. Thanks for the video!
Awesome video thanks! FYI minwax tech support recommends only 100% Spirts not the odorless kind. according to them it could make it more foggy. or affect clarity.
Thank you. I have never seen a cloudy or foggy look in 20 years. Now they do make another kind that is milky as you pour it. I would never use that. Thanks for the information
This is outstanding! I plan on using this method to restore an antique drop leaf dining table. I made the mistake of putting walrus oil on one of the legs (just starting finishing ), but then I saw your video. I would like to know if you can use your method over the top of the walrus oil, or how do it get the table leg ready for your process? Thanks for the formula though!!!
Thank you for the compliment. While I am A huge fan of Walrus oil, I would remove the oil before applying my poly solution. Now I say that because I have never put it over oil before. I might recommend that you email Walrus oil and ask them as well.
Great video! I’ve been looking for a good wipe on Poly mix! I’ll be using this for sure!
Thank you. I greatly appreciate the reply
Thanks for sharing your knowledge and experience. Best wishes!
You are welcome and thank you
A good instructional video, thanks for posting this. I’m getting ready to finish a birch butcher block tabletop for use on a portable basement workbench. I was looking at using the wipeable oil based product, but decided now to mix my own using oil based polyurethane and mineral spirits with your application process. I’m new to wood finishing, and this project will also serve as a test run for finishing a future countertop on cabinets I will install along a wide hallway on my main floor.
Question: I’m going unstained for this initial project, but in my hallway I’d like to do something that will show slightly more grain. I think it is going to be difficult (or very expensive) to find a hardwood countertop (˜112”) with good graining for the hallway countertop, but I can get birch butcher block up to 120” long from big box stores. Do you have any suggestions for staining birch butcher block to enhance the grain slightly, but not overly darken the wood? Most stain application videos I’ve reviewed seem darker than I’d prefer. I do have a couple foot section of extra butcher block left over from the current basement project that I can use for experimentation. Thanks again for the instruction on the poly application and any staining suggestions!
Thank you for watching and for the compliments. As for stain I only use Minwax oil stain. Good choices would be Special Oak, Golden Oak and Puritan Pine are nice light stains. If you don't mind a little red then Gun Stock and Red Oak are nice as well. I would also suggest that you use Minwax conditioner prior to staining to get an even stain.
outstanding soon as the rain stops here I AM ON THIS...
Super. Let me know it works for you. Dries pretty fast
@@BayneCustomWoodworking I got rain for like 6 days
@@knsbbq1951 YIKES
@@BayneCustomWoodworking Project complete worked great. Thank you for your help
@@knsbbq1951 now that is a great way to start the day
Oh my goodness! I am so glad that I searched and found your channel! My daughters mistakenly wasted fingernail polish remover on my table!😢😢 I’ve successfully, due to this video, sanded, restained and added polyurethane to my table and it’s as good as new- thanks to you!!😅😅😊
YIKES! Having children and grandchildren I understand how these things happen. This is the type of success story I like to start the week with! I am glad it worked out for you.
Exactly in the same situation. I accidentally spilled nail polish remover on our new table and ruined the finish. I have hope now. What stain did you use? Thanks.
I’ve loved Minwax’s wipe on poly, I’ve used it exclusively for a decade. I always suspected it was merely a thinned version of their usual oil based poly. You’ve given a good recipe for a make your own version. Definitely cheaper than buying a wipe on poly.
I hope it works well for you as it has me.
Would this also work for Water based Poly and water (instead of mineral spirits)?
Not that I know of. Might be worth a try on a test piece with distilled water.
@@BayneCustomWoodworking would you recommend just using Minwax water based Wipe On Poly instead?
@@anthonydiecidue7916 I am not a fan of water based poly so I would not. Personally I feel that oil based is much more durable.
@@BayneCustomWoodworking I’m finishing a piece of wooden wall art so durability isn’t a concern. I’m just looking for a finish that won’t have a strong odor (trapping the odor of the wood stain if possible) and will keep the wood in a natural/unfinished/satin look
@@anthonydiecidue7916 I have always found that stain has more of an odor than the poly that I make. I actually finish projects inside my house without an issue. But if you have concerns then water based is your best answer.
great video, Im finishing a 8' R/C sail boat
Great video!
Do you use a water-based or oil-based polyurethane?
@@MBMB-sz1ye Thank you… oil base
Thank you for clarifying that.
Sir; Thanks. will try this technique. Had to strip three time. Used Tung Oil Finish which cured very rough. First attempt was with Poly which developed bibbles. redoing my Coffee Table that we bought 25 years ago from Ethan Allen.
Binoy I am glad you found the post and hope you a able to use it to complete your project. Just make sure all the old finish is removed before applying.
I am a newbie what about bubbles?
I do not get bubbles when applying with a rag. The mineral spirits work as a leveling agent
@@BayneCustomWoodworking can't wait to start tomorrow, Thank you
What a great video. Thank you for these very useful explanations. I just had 30 years old pine kitchen cabinets repainted with Farrow and Ball modern eggshell emulsion (water-based). And the kitchen worktops will follow. Should or could I use solvent-based marine polyurethane on them or would standard polyurethane be sufficient. The house is shared with tenants and worktops take a hard beating and need to be easy to clean.
Thank you for the appreciation. Honestly I think you need to talk to counter top professionals before preceding. I know the finish I use will always hold up on table tops. But counter tops take quite a beating. I have used straight floor poly on desktops for soft wood and it’s held up well. But again, counter tops take a beating on a daily basis.
@@BayneCustomWoodworking Thank you and all the best.
In spite of the video edits being faffed up, that's not the point of this video (or channel) and I'm liking your explanations and methods. I'm brand new to polyurethane and I'm practicing on a couple pine slabs. Pretty excited to keep learning more and getting better at it!
Sears or JC Penney for old T-shirts? Any other suggestions?
Any good cotton cloth will do. I just find that old white t-shirts work the best. I am actually looking at purchasing some cotton cleaning cloths to try.
Thank you for the video. Followed your advise and My table top finish turned out much better. However, I see some patches are showing up dull. Is there a quick fix so that I can get an even shine?
Mohib
I am glad it worked out for you. I am not sure why you would have dull spots unless they were sanded differently. Was this fresh wood at the start or was this a refinish project?
Thank you so much for this demo. Does this mix work well over paint as well?
Also is it possible with water based poly? I would prefer if the paint didn’t yellow. Thanks!
Because this is an oil base poly it will not work with water base. I have never put it over paint. Honestly when I need to protect paint I use a spray acrylic from lowes or home depot. I use this on all my grandchildrens toys that I make them when the finish is paint. The odor is quite harsh but after a couple of days it’s gone and some do their toys are years old and have held up well.
@@BayneCustomWoodworking Thank you for your quick response! Just nervous about top coating the paint. Haha, thanks again.
This is a great video and so glad I found it. I think turning off the autofocus on your camera might keep the image from throbbing
Thank you
I will be sanding and staining my fiberglass exterior door. Can this mixture be used on this type of project?
This finish is for interior projects and would not hold up on exterior conditions. I would use an exterior poly on the door
@@BayneCustomWoodworking thank you for replying.
I see your Video too late. I used exact same polyurethane with a brush on first coat. If I sand, then apply your method on the next coats, two parts urethane and one part paint thinner with a rag, will this improve my next topcoats? Thanks for your video!!!
Leonard - Yes but if there are brush marks, try to sand them out but gently. The next coats should apply nicely. Just keep them thin is all. let me know how it comes out
No brush marks as I have been painting for years (@ 67) but not much experience in polyurethane on wood. There are however a ton of tiny bumps. I imagine they are tiny air bubbles that will sand out with a light sanding (320 grit).
Thanks for your response. You are truly amazing ie; response, dedication to your gift. Thanks!
@@leonardbarr6211 no offense intended on the question :-) thank you for the kind words
Bayne just wanted to follow up. I sanded down the original brush coat to get rid of pin head size bumps/bubbles? And used your wipe on method. Since I already had a coating I went with 50/50 twice to level everything out. Then I did your 2 to 1 , (urethane being 2, paint thinner 1)and it worked out perfect. Thanks for your expertise and excellent communication and integrity.
@@leonardbarr6211 This is great news. I am very happy it worked out for you. Thank you for the kind words
Can lacquer thinner be used instead of mineral spirits?
I have not used it, but I am sure you could. However I would test it first
Would you have any recommendations for a white washed butcher block counter top?
James
Are you attempting to refinish and remove the whitewash or are you just trying to seal it? Is it new or old wood?
@@BayneCustomWoodworking its 1 1/2" tongue and groove pine that I sanded to 120 and whitewashed for a counter top. I want to seal it and protect it with something durable enough for everyday kitchen use.
@@BayneCustomWoodworking I also have a pregnant wife so I need to keep the fumes minimal
James ,
I would look at butcher block oil from Walrus oil. It’s similar to the product that I use on all my cutting boards and protects the wood very well. It will certainly be safe for your pregnant wife as well. walrusoil.com/collections/wood-finishes They are very responsive to emails
@@BayneCustomWoodworking thanks!
Will this method work with minwax spar urethane? Or does it have to say "wiping urethane" on the container? I've never stained anything before this month and working on a raw birch pantry currently.
I only use spar finish for outside/exterior projects and never wipe that on. I am sure you could use this method but not sure why you would use spar finish on an interior project. That said this process is making wiping poly so the container will not say wiping polyurethane on it. I hope this helps
@@BayneCustomWoodworking thanks! What type of brush would you use then? I've seen so many different answers online when searching for info and that is the finish the person at Sherwin Williams recommended for a polyurethane when I asked and told them what it was for. Their color/stain match is amazing, but the people checking me out must have been new. One person had zero clue and the other acted more knowledgeable, but I think it was just a show 🙄 it's been frustrating to say the least, I can't wait until this is done. I will leave the large projects for the pros! 🤣 Might try smaller ones for fun.
Help me understand your project. When you say pantry I think of a kitchen pantry for food. Is this what you are building?
@@BayneCustomWoodworking yes a kitchen pantry, which is right by a door to outside so that may be the reason they recommended this finish. It's minwax indoor/outdoor helmsman spar urethane that they recommended. And Zar interior oil base multi-surface stain. I was wanting to do a verethane poly+stain but couldn't find anything close enough to match colorwise.
I would buy the best soft bristle Purdy brush at Lowes or Home Depot. I normally wait 3 days to apply poly after staining, but I tend to be over protective of my projects. Apply light coats brushing with the grain as much as possible. I lightly sand with 400 or 600 grit sand paper between coats and make sure to brush off the residue before applying next coat. With spar finish you could probably get away with 3 coats. Let it dry a day or 2 and the use a brown paper bag to final sand. That works like 2000 grit sand paper and will remove any bumps the poly may leave. This will be great when you are finished. Take your time and enjoy the process.
Hello Roger, this is a very good, no-nonsense, full of information video. I watched it multiple times and saved it in my reference videos.
One question - if I have water based polyurethane can I use same method by substituting water for mineral spirits? In California it is tougher to find regular polyurethane these days.
Thanks and looking forward to more content from you.
I understand there is a process for thinning water based poly but you have to contact the mfg for the information- sorry
Can you add stain to the mix at 1 part poly and 2 parts of M. S, this way you get it all in one ?
A number of companies make stain mixed with poly. I am not a fan and would not make the mix myself.
Oh no! I used Tung oil instead of polyurethane!! Can this be fixed as is or do l need to start all over again with the 80, 120,320 sanding!?!
What are you building? Did you thin the tung oil?
@BayneCustomWoodworking l used your 2 to 1 ratio ( as for your polyurethane). Sticky 48hrs later, handled w/0000 steel wool. It's a pine carpenter's table from the hardware store. I don't know if this poor table will survive me!
@@NaNana-ey6jk I would sand it off and either use straight Tung oil applied lightly, let sit for 15-20 minutes and wipe it off. Then let it dry. Or re sand and start over with poly mix. You got this
@@BayneCustomWoodworking used the 320. Was sticky, bucking. Go to 80?
Yes I would go all the way back to 80 and work your way back to 320
Hello Roger. I was attempting my first stain project and was having difficulty applying a clean poly clear until I found this video. THANK YOU for saving my sanity! Beautiful solution for me. THANK YOU THANK YOU THANK YOU
I love to hear success stories. I appreciate you sharing and glad this helped make you successful
Do you have a video on that exterior spar finish for doors?
I just looking for a video of me spraying some chairs and I am not sure we have ever created one. I will have to get one recorded soon. Are their questions I can answer for you?
Great video. Simple process that I will definitely try.
Thank and please let me know your results
TY , Gonna give this a chance ! Be well in '21
How does this way work on six panel solid doors.
I have found this works great on any inside wood products
We made a wipe on solution and wiped it on with a cotton rag to finish some red oak doors we stained. It seems to streak…. Like some parts were dull from the mineral spirits and then we had shiny streaks from the polyurethane. We stirred the solution often too. Does wiping it on with a circular motion alleviate these streaks?
Hmmmm, I am not sure what would cause that. Are you using oil poly and regular mineral spirits and not the spirits that is milky looking?
What rags do you use with wipe on finish
Cotton tshirts or cotton rags
Do you light sand between each coat
Normally only between coats 4 and 5 unless I feel any roughness between other coats
Just a question. Can this same mixture be applied over a piece of newly stained furniture if the stain is allowed to cure long enough?
Yes.98% of my applications are this way. I normally let my stain cure forn72 hours before applying the poly.
thanks for the info. I was planning on waiting just about that length of time if not a day or two longer just to be sure. @@BayneCustomWoodworking
Can't wait to see the finished result! Thanks!
Thank you for sharing this with us. Very informative. I have been trying to decide the best finish for a black walnut “waterfall” table which is 18” on one end and 27” on the crotch end. I initially considered epoxy, but that would make many runs on the waterfall end. Also, I’m leaving the bark on the live edge, albeit after sanding about 1/2 off so it doesn’t catch on pants legs, etc. This method should allow me to use this on the edges so it can “soak” in providing a smooth finish. Again, many thanks!!
I am glad you found it.. I look forward to seeing the finish product. Thank you for following
what did you call those pointed feet? Statins? Where can I get some of those please?
Those are painters tripods. You can find them at lowes, home depot or amazon
Thanks I going to try it on some tables! Excellent workmanship!👍
Thank you…please let me know how you make out.
Great video. I learned a lot to pass it on to my wife
Thank you
Nice video. Quick question, does the wood need a seal application before using this wipe on ?
Thank you. No it does not.
This is a game changer for me Thanks. I do wood signs and hate the sanding in between coats plus brush stokes that have to be careful of. ☝
Now this is the way to end my day. Thank you for the comment and I look forward to seeing a finished product. Do you have an instagram I can follow?
Excellent explanation! Thank you for sharing your technique.
Thank you and you are welcome
Is this technique recommended for floors?
I would not use this for floors. While durable for tables, cabinets, etc... I would not recommend for floors
Can this be done with water based finishes.
I normally do not work with a water-based polyurethane but if I do I would use general finishes high performance water base. They state on their product that you can thin it with distilled water at about 5% up to about 10% I've never tried it but they look like they can. but I'm always a fan if I'm going to put water-based on I'm going to put it on with a good high quality roller or spray it or even a good high quality foam brush but again I don't use water base very often
I've found that brush-on poly (uncut) wiped on with printer paper works great for guitars, but spray lacquer is faster and easier.
Thanks.
I actually used rub on gloss poly on a Tenor Ukelele I had built. I do wish I had seen this first because a 2 part thinner to 1 part poly as the first two coats where the thinner mix helps level is a great idea
Thank you. That sounds like a wonderful and challenging project. Thanks for subscribing
@@BayneCustomWoodworking the project took 7 weeks of about 3 to 4 hours a day 5 to 6 days a week to get to the apply finish stage, but it was entirely scratch built including cutting the thin strips that were glued up to form the top and back plus all the jigs and molds needed.
But it has been so much fun that I have another Tenor Uke a bit over 1/3 built in the works plus I ordered a guitar kit from Stewmac. Actually the guitar kit will be a lot easier because a lot of work has been done by the supplier.
Until this, the biggest project I completed was a 15 by 20 foot summer Cabana that took 800 hours to complete. The first Uke will have about 200 hours into it, but considering square feet of build it easily is the longest project ever for me.
I think any one that has a bandsaw and a way to achieve thickness sanding plus a bit of patience can build a stringed instrument. The kits can save a large amount of time. Stewmac is great for quality I've heard but pretty pricey unless like me you buy a once in a blue moon sale. Maderas Barber in Spain seems to have nice kits at very reasonable prices but if you have the two tools I indicated you spend very little especially if you buy rough cut and plane with even a small electric hand planer which is what I used. It is actually a favorite tool and only cost $45 at Harbor Freight. My thickness sanding could be easier but it works and I use a 6 by 48 belt sander attached to my Shopsmith.
The bending I achieved with steam. Matthias Wandel used a rice cooker, others use a wallpaper steamer. I used an electric skillet with lid plus I would thoroughly wet the side piece and use a steam iron on it too. It worked really well.
What is really cool is whether guitar or Ukelele you have an instrument that with a soundboard made of Red Spruce or Cedar or Redwood as I used and an all solid wood construction that will rival a Martin or Santa Cruz or Taylor instrument that can cost easily $10,000 for probably in the neighborhood of $100 and the difference in sound between your solid top and a laminate top is like Am transistor pocket radio to top notch stereo system.
I really would encourage anyone to give building a stringed instrument a go. It's too much fun and too much reward to let it pass if you have tools that are sufficient for the job at hand.
Take care,
Like your channel, glad TH-cam recommended it to me...
I will definitely use your method and mix on my table. Thanks! BTW where did you find the metal leg pieces on the wood tables you made?
Thank you , let me know how it works out for you. I buy my legs at hairpinlegs.com
How long can you store any left over mix if sealed properly?
I never store it. I only mix enough for the present project.
I never store it. I only mix enough for the present project.
Thanks
Is that water base minwax ? Or oil?
This is oil based minwax
@@BayneCustomWoodworking Thank you sir. Great video and can’t wait to try this method
@@Jetski270 Thank you. keep me updated on your results
Where do you get the legs from
www.diyhairpinlegs.com/
Does this work with water base semi-gloss same brand, I restore vintage travel trailers mostly birtch 4'x8' panels brushes and rollers don't work well, spraying is better but dries in the gun to fast, thank you.
This is a oil base mixture and would not recommend with water base. If I do use water base it’s always with a high quality brush.
Can this be done with water-based poly?
@@Callmeconfused-i7q Honestly I have never tried it. I have heard you can thin it with water but I have never tried it