What a tidy bit of kit I lived in Queensland for years among some big plantations of pine never saw a bit of kit like that.Tidy Bach wish I had one here in Cymru. If I win lotto hay !!!!
These swing blade saw videos never seem to show more than the first 2/3 of the log being sawn. What happens when you get down to the last couple inches of that log? What holds it in place?
Well I can tell you it's not a conspiracy. The usual process is you cut a 6" x 2" wide notch in your support bunks. The log simply cradles into these. The two edges hold the sides of the log. When you get to the lowest point the only tendency is for the log to slide sideways to the left as this is the direction the blade is going. Because it sits within the two edges its impossible for the log to slide. Typically the log does not lift as its fighting against gravity in the vertical. That coupled with the fact that a single blade creates very little resistance. You may be familiar with a twin saw which has a tendency for two blades to work together and throw the work peace. Swing mill is very different - in fact when sawing your bottom cut you can take your cuts in smaller (2 step) increments to further reduce the drag caused by the blade. Hope that explains it :-) if you want to see mills go right down to the bottom thinnest slab have a look on turbosawmill's facebook page. Here is a link of this mill sawing a log down to absolutely nothing... th-cam.com/video/fb-fjQ7OJm4/w-d-xo.html Cheers. Jake.
Thanks Jake! I didn't figure it was a conspiracy, just was odd none of the videos I watched showed it! lol I wasn't sure how much drag the blade created. I'm used to bandsaws, which simply pull the last board to the left against the stops. But as the blade enters the wood, it can sometimes make the far end pivot to the right on short logs.
Still haven't seen what I was hoping to see from Turbo or Lucas Mill which is slabbing with a circular saw cutting horizontally done one side of the log and then horizontally down the opposite side of the log?
thanks I just bought a used one and it's a 10 inch and I want u to give me the size of the same 2 belts that connects the engine pulley and gear box pulley (blade conne ct to)and the other one(1belt) that connects the engine pulley and the gearbox that moves engine front and backwards.Thanks I'll get in touch for further information .I live in Santo. Vanuatu
Link for US sales. www.turbosawmillusa.com/new-products/6-cut-honda-gx390-13hp-warrior-sawmill Bit over my pay grade though. even for the model 6 manual. I liked ,Shared.
Please check out utube channel How Farms Work and One Lonely Farmer. There is a farm day in Petosi Wisconsin. August 19th. Over 200,000 subs. Olf has a wm..50. They have trees and need building rough sawn lumber. Lucas gave Wranglerstar a mill to use for 2 years for advertisong. Great family..get a local owner to attend and split production. Take a 3 pt chipper and dump trailer.
What a tidy bit of kit I lived in Queensland for years among some big plantations of pine never saw a bit of kit like that.Tidy Bach wish I had one here in Cymru. If I win lotto hay !!!!
I am sold, this is the coolest!
OKEY. YESS. TEHNOLOGIES. GUD. !!!
How much would it cost to ship it to Kenya?
Am I seeing this correct? You can move the mill to the log ??
This is the BEST and most Efficient mill I have ever seen. I want one !
Yes you can.
Looks like a giant radial arm saw still this is a nice mill
Soy de Colombia me gustaría tener info sobre estos Aserrío y sus precios
These swing blade saw videos never seem to show more than the first 2/3 of the log being sawn. What happens when you get down to the last couple inches of that log? What holds it in place?
Well I can tell you it's not a conspiracy. The usual process is you cut a 6" x 2" wide notch in your support bunks. The log simply cradles into these. The two edges hold the sides of the log. When you get to the lowest point the only tendency is for the log to slide sideways to the left as this is the direction the blade is going. Because it sits within the two edges its impossible for the log to slide. Typically the log does not lift as its fighting against gravity in the vertical. That coupled with the fact that a single blade creates very little resistance.
You may be familiar with a twin saw which has a tendency for two blades to work together and throw the work peace. Swing mill is very different - in fact when sawing your bottom cut you can take your cuts in smaller (2 step) increments to further reduce the drag caused by the blade.
Hope that explains it :-) if you want to see mills go right down to the bottom thinnest slab have a look on turbosawmill's facebook page.
Here is a link of this mill sawing a log down to absolutely nothing... th-cam.com/video/fb-fjQ7OJm4/w-d-xo.html
Cheers.
Jake.
Thanks Jake! I didn't figure it was a conspiracy, just was odd none of the videos I watched showed it! lol
I wasn't sure how much drag the blade created. I'm used to bandsaws, which simply pull the last board to the left against the stops. But as the blade enters the wood, it can sometimes make the far end pivot to the right on short logs.
Still haven't seen what I was hoping to see from Turbo or Lucas Mill which is slabbing with a circular saw cutting horizontally done one side of the log and then horizontally down the opposite side of the log?
2thelightphoto like this?... th-cam.com/video/pEsHzPVdKOg/w-d-xo.html
Great looking machine !
EXELENTE! NICE!!!!!
me.gustaria representarlos en Centro America envienme mas informacion
Is it still priced at $10,000?
do you have a reliable website?
Quanto que custa uma máquina desa de vcs por favor me responda eu brasileiro e queria que vcs me manda a resposta em brasileiro
Wouldn't be better on the blade and wood to cut horizontally first?
TheWaterman1000 only if the timber was to heavy and affecting the blade otherwise it’s advantageous vertical first.
How can we find that saw mill in india.
Please tell me
Just email jake@turbosawmill.co.nz the new equivalent model is powered with the Honda 13hp motor.
Cost?
Mesin kayak gini di indonesia apa sudah ada?
Wer Verkauft diese Maschine in die Schweiz
Porque eu estou precisando muito de uma máquina desta
Why not in the EU ??
We are in the EU. Fully CE certified.
awsome product guys! you should send one to Cody at the Wranglerstar channel. he has a ton of subscribers and this is his kind of thing. Cheers!
GREAT idea. :)
yeah I can see it now, 6 episodes 25 minutes minutes each and he shows you how to put gas in it.
Make sure you let him know it's "Metric"! lol
I am in indea and I am buying turbo sawmill
See marketing idea below. Great product.
Wow, awesome !!!
harika bir makina fiyatı nedir
How do I get touch you? Web site?
Yes contact us
www.turbosawmill.com
@@TURBOSAWMILL Thank you.
I live in Vanuatu how much it cost in vatu worrior auto ,how can I get one
1,990,000 email retail@turbosawmill.co.nz
thanks for replying ,that price suit what size of inch blade?
8"
thanks I just bought a used one and it's a 10 inch and I want u to give me the size of the same 2 belts that connects the engine pulley and gear box pulley (blade conne ct to)and the other one(1belt) that connects the engine pulley and the gearbox that moves engine front and backwards.Thanks I'll get in touch for further information .I live in Santo. Vanuatu
where do i go to find out the price of your mills ?
Give me your email and I'll get pricing to you now.
+TURBOSAWMILL or email us at jakep1@xtra.co.nz
+TURBOSAWMILL mainly interested in this new warrior and the next model up . garywhelton57@live.com
TURBOSAWMILL made in nz?
Yep made in NZ. Email jake@turbosawmill.co.nz where are you from?
Why not in the US?
Not sure what you mean? We have a US distributor...
TURBOSAWMILL
Link for US sales.
www.turbosawmillusa.com/new-products/6-cut-honda-gx390-13hp-warrior-sawmill
Bit over my pay grade though. even for the model 6 manual. I liked ,Shared.
Please check out utube channel How Farms Work and One Lonely Farmer. There is a farm day in Petosi Wisconsin. August 19th. Over 200,000 subs. Olf has a wm..50. They have trees and need building rough sawn lumber. Lucas gave Wranglerstar a mill to use for 2 years for advertisong. Great family..get a local owner to attend and split production. Take a 3 pt chipper and dump trailer.
We have products near that price.
l really interested turbo sawmill. I want to purchase one but portable and minimum cost.
TURBOSAWMILL
Wes Cargill price?
Gekong Pertin ..
Can you send me your details and price for the buy
That is a lumber making sob .
Southeastern Ohio Honeybees