Also I should point out if you want to center your calipers you just leave the screws loose and squeeze the lever to clamp the pads down. Hydraulic brakes can center them selves just like that
could you tell me the name and description of the kit you used to switch the banjo bolt and hydraulic line over to the outside of the caliper? the one you have listed here is no longer valid.
Thanks for the video, but change the camera angle while the technician is doing the install, so we can get a better visual. Again, thanks for the video.
Thanks for your feedback. Nutt brakes are actually considered the most value for money performance brakes set. Magura brakes require regular changing too as the brake pads wear out quite fast. Most high performance brake pads are like that unfortunately.
@@FalconpevSg I've been looking at the Magura MT7 Pro Brakes do you know if they will fit on my Kaabo Wolf King GT if not what do i need to measure to ensure they fit ?
Hey how are you, wanted to know if this also applies to the kaabo wolf king gt pro, well I guess the question is can I upgrade my kaabo breaks to magura brakes.
I guess for the same reason why its on the same side as brake disc so when you have to change disc, you have to disconnect cable etc. Poor design skills.
Hello! Good job! One question: If I buy the Magura brakes for my 160mm brake discs for my converted Xiaomi 1s, then with the MAGURA brakes the brake hose is on the inside near the tires and that is very close to the distance to the tires. Can I, like you, unscrew this brake hose from the inside where it is originally on the brake hose, also on the inside and then clean and screw the small oil screw and then mount this oil brake hose on the outside on the brake? If I unscrew the oil screw on the outside and screw the oil hose in on the outside?? Does this work with the front and rear MAGURA 4 piston brakes? So take the oil pressure hose from the brake, which is on the inside of the tire, and screw it on the outside where the oil comes in? Because you have the hose on the outside but the original when you buy the MAGURA brakes, this oil pressure brake hose is mounted on the inside at the back and front! Can you do this without having to mount the hose on the outside? I'm ASKING you to answer this question and help me a lot! Because then I could buy the MAGURA brakes and get them tomorrow! I just need to know whether you can screw the oil hose away from the inside of the tires and onto the outside like you installed the brake hose at the rear of the outside brake. Kind regards. 👍
So where did you get the banjo to fit the 6mm bolt? I have the brakes and the bolt you provided does not fit through the eye of the banjo bolt. Do i need a specific banjo? Thanks in advance
Instead of moving the banjo bolt to the other side, is it possible to leave the banjo bolt as it and install it as is? Maybe with a spacer or two should lift it high enough to not effect the braking.
good evening i need your help I want to buy them Magura MT5e Disc Brake but in a site writing 2 Version -with HIGO closer no and with HIGO opener no - which one should i choose for my scooter speedtrott rx 1000 thank you very much in advance
I bought a Magury mt5 e for Vsett 10+ but the hose attachment is on the opposite side than you have. Could you tell me to have it like you? If necessary, give a link to Ali as needed, thank you
I am curious. Are there any pros/cons to the larger/thinner mtb rotor vs the stock smaller/thicker rotor. Is there a difference in pad thickness? For stock vs magura caliper/pads?
very good questions. scooter hubs with their high rpms generate a ton of heat and heat is the enemy of metal as the rotors tend to get bent creating uneven braking feel. the larger/thicker rotors will prevent that.
Hi, I ve got electric scoooter Motus 10 pro sport 2021 - it seems to be idential. Can any of you confirm that it will be compatible with Motus 10 pro sport 2021 ?
hello is it ok to put a motorcycle oil pan on the top of the break lever so the oil is rotating like the motor cycle they have an oil pan on the top of break lever? thanks
good morning friend I have the magura brake system but my electric scooter is a nanrobot d6 the brake adapter you used for the zero 10 would work for my nanrobot d6 scooter I hope you can help me thanks
Hey how are you wanted to know if that monitor on your scooter is a rearview digital camera if so what model is that because I picked one up but the wiring is too short. Thank you in advance for your reply
Can this setup be put/used on the Kaabo mantis Elite too? And when we purchase the mt5e brakes mt7 etc.. Dose it come with the rotor and leavers as well??
@@FalconpevSg Have you any idea where i can get one, the brakes are horrendous quality that come with the King GT. Magura brakes are really good I've used them in the past.
These are hydraulic brakes too, except these are considered the gold standard used for racing performance with massive stopping power. We normally do not install them that much.
@@FalconpevSg oh okay so if I already have a zero 10x with zoom hydraulic brakes, there isn’t a significant difference between those and magura or nutt brakes?
@@FalconpevSg At the very beginning of the video, we see a black colored part which is attached to the rear swing arm, if it is not a fender, what is this part, I am interested ???
@@FalconpevSg Yes. Commonly all bicycle brakes are installed on the left side.. my DNM USD-8 FAT fork has 2 disc mount (left and right) I intend to install on the right too. But I don't know how to start.. are u able to guide me?
@@FalconpevSg + one more thing why didnt u use magura e bike breaks and wired them up to the scooter because the customer whanted it that way or ? Because thats only usefull if ur doing wheelies on it and -1 in safety because if u disconect ur break cable and ur throttle gets stuck on full power only way to stop it from going anyhwere is turning the key off witch is vrey dificult if the scooters wheels are spining or just pressing the break but u disconected them so that is not going to help
So where did you get the banjo to suit the 6mm bolt? I have the brakes and the bolt you supplied will not fit through the eye of the banjo bolt. Do I need a specific banjo? Thank you in advance
Haha 😂 no it’s not that, different brakes have different configurations, so you have to adapt it for different bikes. Magura is very flexible because you can use either of the 2 bleeding ports as your hose inlet.
![ร้อยพ่อพันแม่ - WanMai [Official MV]](http://i.ytimg.com/vi/XY2pNYASEbg/mqdefault.jpg)
Also I should point out if you want to center your calipers you just leave the screws loose and squeeze the lever to clamp the pads down. Hydraulic brakes can center them selves just like that
Wow never thought of this 🤝
could you tell me the name and description of the kit you used to switch the banjo bolt and hydraulic line over to the outside of the caliper? the one you have listed here is no longer valid.
Hello, the adapter could work on a VSett 11+?
did it work?
Thanks for the video, but change the camera angle while the technician is doing the install, so we can get a better visual. Again, thanks for the video.
Thanks for your feedback. Nutt brakes are actually considered the most value for money performance brakes set. Magura brakes require regular changing too as the brake pads wear out quite fast. Most high performance brake pads are like that unfortunately.
@@FalconpevSg I've been looking at the Magura MT7 Pro Brakes do you know if they will fit on my Kaabo Wolf King GT if not what do i need to measure to ensure they fit ?
1:57 - someone installed NUTT brakes in that shop
Hey how are you, wanted to know if this also applies to the kaabo wolf king gt pro, well I guess the question is can I upgrade my kaabo breaks to magura brakes.
Did you try it out?
Are you using MT5e HIGO-Closer or MT5e HIGO-Opener for ZERO10X?
Why does your hub motor wiring come out the end of your axle like that??
I guess for the same reason why its on the same side as brake disc so when you have to change disc, you have to disconnect cable etc. Poor design skills.
Hello! Good job!
One question: If I buy the Magura brakes for my 160mm brake discs for my converted Xiaomi 1s, then with the MAGURA brakes the brake hose is on the inside near the tires and that is very close to the distance to the tires. Can I, like you, unscrew this brake hose from the inside where it is originally on the brake hose, also on the inside and then clean and screw the small oil screw and then mount this oil brake hose on the outside on the brake? If I unscrew the oil screw on the outside and screw the oil hose in on the outside?? Does this work with the front and rear MAGURA 4 piston brakes? So take the oil pressure hose from the brake, which is on the inside of the tire, and screw it on the outside where the oil comes in? Because you have the hose on the outside but the original when you buy the MAGURA brakes, this oil pressure brake hose is mounted on the inside at the back and front! Can you do this without having to mount the hose on the outside? I'm ASKING you to answer this question and help me a lot! Because then I could buy the MAGURA brakes and get them tomorrow! I just need to know whether you can screw the oil hose away from the inside of the tires and onto the outside like you installed the brake hose at the rear of the outside brake. Kind regards. 👍
So where did you get the banjo to fit the 6mm bolt? I have the brakes and the bolt you provided does not fit through the eye of the banjo bolt. Do i need a specific banjo? Thanks in advance
Hi where did you buy the M6 bolt can you please send the link? nice Video BTw
Do you have MT5e HIGO for the right side or did you modify anything?
we only modified two things: 1. added the adapter bracket 2. changed the banjo bolt to the other side.
Instead of moving the banjo bolt to the other side, is it possible to leave the banjo bolt as it and install it as is? Maybe with a spacer or two should lift it high enough to not effect the braking.
It’s possible but the risk of tire rubbing against the hose is too high.
@@FalconpevSg is it possible to install the mt5e without using the rotor spacer? Also is 0.2mm rotor spacer enough?
Whats that display in the center of the handlebar?
If you used a 140mm rotor do you still need the adaptor IS mount? Also is that a stock Magura mtb rotor that you installed?
good evening i need your help
I want to buy them Magura MT5e Disc Brake but in a site writing
2 Version -with HIGO closer no and with HIGO opener no - which one should i choose
for my scooter speedtrott rx 1000
thank you very much
in advance
Did you figure it out? I'm looking at the same brakes for my 10X.
Bought the mt5e but calipers are different then yours. Can't swap lone
@@paulastry5842 hmm it should be able to
I ordered the mt5e with Grey caps. Probably ha e to take to shop and see if it will work. I'm using right side adapter bracket.
cant you just combine nutt brake levers with magura calipers?
Why would you do that? You won’t get the full Magura braking experience. The levers are the best part
リア用のブラケットをフロントに付けて使用できるでしょうか。
Hi can you tell me where can find about zero10X brake adapter because I want to upgrad the brake to mt5e thx the info
here you go www.falconpev.com.sg/products/magura-right-side-adapter-for-zero-10x-and-11x
Very good instructions 👌
Thank you! Cheers! hope it helps
I bought a Magury mt5 e for Vsett 10+ but the hose attachment is on the opposite side than you have. Could you tell me to have it like you? If necessary, give a link to Ali as needed, thank you
Everything is in description, pls read
I am curious. Are there any pros/cons to the larger/thinner mtb rotor vs the stock smaller/thicker rotor.
Is there a difference in pad thickness? For stock vs magura caliper/pads?
very good questions. scooter hubs with their high rpms generate a ton of heat and heat is the enemy of metal as the rotors tend to get bent creating uneven braking feel. the larger/thicker rotors will prevent that.
@@FalconpevSg thank you. I have 145mmx 3mm rotors on my wolf. would I be able to use the stock rotors with mt5e? should I?
Oh if they are stock rotors then they should fit but we are not sure cos we don’t know what’s a wolf
@@FalconpevSg kaabo wolf warrior gt
Do you sell the 6mm banjo to install right side on zero 11x?
How many mm are the disc rotor spacers?
how you connect the brake light please explain for more viewers
The existing brake already has a ebrake wire, simply solder the brake wire onto the old wire.
Que frenos y disco le puedo colocar a mi dualtron X2
Hi, I ve got electric scoooter Motus 10 pro sport 2021 - it seems to be idential. Can any of you confirm that it will be compatible with Motus 10 pro sport 2021 ?
can i use that for my nami burn e
hello is it ok to put a motorcycle oil pan on the top of the break lever so the oil is rotating like the motor cycle they have an oil pan on the top of break lever? thanks
good morning friend I have the magura brake system but my electric scooter is a nanrobot d6 the brake adapter you used for the zero 10 would work for my nanrobot d6 scooter I hope you can help me thanks
I don’t know
very nice video as always :)
Do i need spacers when fitting Magura MT5e stop brakes on my Zero 11x?
yes for the rotors
and the calipers
@@FalconpevSg spacers for calipers,what they look like?
@@FalconpevSg ok ordered some to day from FalconPev so hopefully they arrive fast
@@nathanjones6908we use tapered edge spacers to adjust both height and angle
Will this same adapter and magura kit work for the vsett10+?
yes it will but your rear mudguard may need to be modified to fit.
@@FalconpevSg I actually upgraded to a carbonrevo mud guard does that make things easier or worst? Thank you
@@escoot_nyc1651 yes it’s much easier
When you change the brakes can you does the brake lights still work?
@@CaptainSpacedOut yes because these are the estop version with the ebrake function
Fit on the Zero 8X to? Greetings from Vienna 😎
magura can fit, but you need to do abit of adjustments.
Un video sobre la pantalla lcd gracias
Hey how are you wanted to know if that monitor on your scooter is a rearview digital camera if so what model is that because I picked one up but the wiring is too short. Thank you in advance for your reply
No it’s an lcd for the scooter
@@FalconpevSg oh ok no problem thanks again for getting back to me
Are there any new parts to buy that change the banjo from the outside? Sorry for asking so many questions.
You need the adapter bracket too
What is that display?
Can you not swap the screws of the hydrolic cables?
No they aren’t the same
How to swap hose port on magura ?
You need a banjo bolt conversion
@@FalconpevSg why exacly dont you just reuse the stock banjo bolt ?
@@Maykay1312 good question, the original bolt is too long for the port
@@FalconpevSg so the aftermarket banjo is shorter right so it fits inside ? And u just put the bleed port screw where the original banjo was ?
@@Maykay1312 yes correct
Can this setup be put/used on the Kaabo mantis Elite too? And when we purchase the mt5e brakes mt7 etc.. Dose it come with the rotor and leavers as well??
Dance with Timothy! We aren’t sure what the Kaboo is
@@FalconpevSg ahh :/
Disculpa y que pasa con el freno electrico ? El magura mt5e tiene para incorporarle freno electrico ?
Se queda desactivado
Very nice video guys. Respect :)
Thanks so much!
@@FalconpevSg Could you put these brakes on a Kaabo Wolf King GT.
@@originalityisdead.9513 yes you can but you will need an adapter
@@FalconpevSg Have you any idea where i can get one, the brakes are horrendous quality that come with the King GT. Magura brakes are really good I've used them in the past.
@@originalityisdead.9513 are they zoom brakes or nutt brakes
Do you have anything new to prepare other than the adapter bracket?
Hmm just get it and try. The more you try the more you learn. We cannot teach you everything
I’m looking to upgrade my brakes on my Zero 11x to Magura MT7. This will negate the brake lights when the levers are pressed?
You will need Magura mt5e model, so the stop lights would work
@@Fanta.Inc. actually all is needed is a micro switch. Already done.. thanks
@@seanvin66 alright, thanks for info!
Hey i need help with the two bolts buddy on swapping them can u help so i dont order the wrong stuff again
What two bolts
The banjo bolts?
@@FalconpevSg the new banjo screw and other screw for swapping sides
@@FalconpevSg yes
Very good
why would you want to change your brakes and rotor to a 160 because my zoom brakes are a 140 and they stop on a dime ???
Zoom brakes are considered Low end hydraulic brakes which are not as strong especially if you upgrade your motors
@@FalconpevSg OK but my zoom hydraulic brakes stop my Varla eagle one/zero 10X on a dime every time so why should I upgrade ???
@@RickyD1968 then don’t upgrade if it works for you
how can i remove the wire that goes inside?
why would u want to do that
What type of tires are you have? What measurements are they?
Jose Isaza 10x3 www.falconpev.com.sg/products/zero-10x-tire?_pos=1&_sid=609da65a3&_ss=r&variant=15866791559235
What’s the difference between these and hydraulic brakes? Is there a significant difference
These are hydraulic brakes too, except these are considered the gold standard used for racing performance with massive stopping power. We normally do not install them that much.
@@FalconpevSg oh okay so if I already have a zero 10x with zoom hydraulic brakes, there isn’t a significant difference between those and magura or nutt brakes?
@@l-Lucid-l yes significant difference.
@@FalconpevSg okay it is worth the upgrade then. Do you have these brakes in stock for purchase?
@@l-Lucid-l go for the Nutt brand it’s a workhorse better than zoom
Hello, where to find this type of rear fender, thank you for your answer ???
jean-françois Richard what rear fender?
@@FalconpevSg At the very beginning of the video, we see a black colored part which is attached to the rear swing arm, if it is not a fender, what is this part, I am interested ???
jean-françois Richard that’s a rear box bracket
@@FalconpevSg And can I see it or ???
jean-françois Richard yes you can see on our Facebook www.fb.com/falconpev
are you using higo opener or higo closer?
we cant remember sorry.
Can it be installed on Normal bicycle?
You mean Magura?
@@FalconpevSg Yes.
Commonly all bicycle brakes are installed on the left side.. my DNM USD-8 FAT fork has 2 disc mount (left and right) I intend to install on the right too. But I don't know how to start.. are u able to guide me?
@@mohamadhaikhal5860 yes sure this video shows you how to do it
@@FalconpevSg are u able to install for me, I hope u r aware we are chatting on a normal bicycle.
@@mohamadhaikhal5860 yes we can install on normal bicycle
I will lose brake lights and ebraking?
Arthur Rapsky Raffy no you won’t because you can use the electric brakes still
@@FalconpevSg how?
@@FalconpevSg how?? Magura send negative pulse.
11 inch wheels?
That’s the Evo
What tires are those?
those are our 10x3 extra wide tires
verry good !!!
im prety sure ur not suposed to touch bycicle break discs with greasy hands and u shoud use locktight on the breaks
Thanks for the feedback.
@@FalconpevSg
+ one more thing why didnt u use magura e bike breaks and wired them up to the scooter because the customer whanted it that way or ? Because thats only usefull if ur doing wheelies on it and -1 in safety because if u disconect ur break cable and ur throttle gets stuck on full power only way to stop it from going anyhwere is turning the key off witch is vrey dificult if the scooters wheels are spining or just pressing the break but u disconected them so that is not going to help
Is the red brake line Magura or aftermarket?
aftermarket
So where did you get the banjo to suit the 6mm bolt?
I have the brakes and the bolt you supplied will not fit through the eye of the banjo bolt.
Do I need a specific banjo?
Thank you in advance
that banjo is on the wrong way,
how so
The designer who designed it the way the brake disc in on the side of a cable should be fired.
Haha 😂 no it’s not that, different brakes have different configurations, so you have to adapt it for different bikes. Magura is very flexible because you can use either of the 2 bleeding ports as your hose inlet.