Repairing two drill press spindles
ฝัง
- เผยแพร่เมื่อ 16 ก.ค. 2024
- My friend Johan paid me a visit and brought two damaged drill press spindle shafts with him.
The two drill presses in question are a German Flott and a Swedish Strands.
I helped him out with those.
In this video I use:
- Weiler Matador SV (1972) Lathe
Chapters:
0:00:00 Opening animat-Io-n
0:00:43 Introduction
0:02:17 Flott shaft: Drill chuck taper clean-up
0:10:59 Flott shaft: Turning outer diameter for M14x1 thread
0:14:47 Flott shaft: Single-point threading M14x1 thread
0:22:52 Flott bearing adjustment nut: Outer diameter
0:27:08 Flott bearing adjustment nut: M14x1 thread
0:34:19 Flott bearing adjustment nut: Parting off
0:39:23 Flott bearing adjustment nut: Finishing the nut
0:42:19 Strands shaft: Clean-up of the hammered flange
0:46:20 Strands shaft: Inspecting the Morse 3 taper
0:47:19 Strands shaft: Drilling more space for Morse 3 reamer
0:49:26 Strands shaft: Reaming with Morse 3 reamer
0:52:48 Strands shaft: Bearing spacer ring
1:03:20 Photo album and final summary
1:06:09 Closing words and end credits
All music in this video was composed by Scott Joplin (1868-1917).
Some of the music was played in by Jim Paterson and Sue Keller.
Rest of the music was played in by me.
Music in this video:
A Breeze From Alabama
Elite Syncopations (Jim Paterson)
Euphonic Sounds
Gladiolus Rag
Heliotrope Bouquet (Sue Keller)
Maple Leaf Rag
Peacherine Rag
Pleasant Moments
Sunflower Slow Drag (Jim Paterson)
Swipesy Cakewalk
The Cascades
The Chrysanthemum (Jim Paterson)
The Easy Winners
The video is spoken in Finnish but it has good quality hand written subtitles in English, German and Finnish. - วิทยาศาสตร์และเทคโนโลยี
Oli taas erittäin mielenkiintoinen työvideo, kiitos sitä 👍
good video finno
Tosi mukavia videoita teet ja vielä SUOMEKSI. Rauhallisesti kerrottu , mitat, nopeudet sekä kuvat hyvin esillä. Mielestäni auttaa minunlaisiani harrastelijoita ja luulen että tuo omaa rohkeuttakin toimia. Varsin itse pidän näistä korjaus/"ongelma "ratkaisuista, mutta myös uudet jutut kuten mittakellon pidin ja vastaavat ovat tosi mielenkiintoisia. Olisi myös mukava kuulla "työhistoriaa" jossain videossa, luulen että näitä monipuolisia taitoja ei ihan tallissa ole opittu. Animaatiot on mukavia, mutta musiikki hieman häiritsevä kun ei meinaa kuulla kaikkia yksityiskohtia, voisiko soittaa hieman hiljempaa.
Hi Fino,
To prevent the chisel from causing a scratch internally when turning the slide back, you can push the rod on the QCTP towards the opening with a little pressure. This will prevent the chisel tension from causing the scratch and your workpiece will also remain neat internally. Otherwise it will be bether to make a springpass for precision measerments.
nicely done !
Here for the intro
Lataa puhelimeesi camcut appi. Siinä on oikeastaan kaikki taulukot, mitä kotikoneistaja tarvitsee, ja on toki työelämässäkin lähes korvaamaton apuväline on kiereiden halkaisijat yms tiedot
Mulla on iso taulukko sinälle niitattuna. Tykkään enemmän paperiversiosta :)
Noin syvistä pihdin jäljistä voi huoletta ottaa heti kerralla 0,3mm vähintään pois