My esc only has one black and red wire to connect to the motors, I bought 4 of them to use them as a motor for propellor for my ship, how do I connect them all together to the receiver? Or are they just independently
Tengo un motor 550 de un clon de tamiya Tl-01 y cuando le conecto este ESC al subir al maximo la potencia empieza a cortar ✂️ la energía y me descarga la batería muy rápido como si estuviera en "corto circuito". Lo interesante esta en que le conecto cualquier otro motor del mismo tamaño y funciona sin problema. No logro entender que pasa.... El motor consume mucho mas aperaje que este controlador??? O mi controlador venia dañado?? 🤔
This esc is junk it's way over rated from the specs it is rated at it should have ran my 15t motors on 3s no problem but it blew up in under a minute it was the second run . first was 2s then tried 3s and boom . it was in my clod buster . don't waist your money on this just get a hobby wing 880
@@solarsynapse so my radio is weird for me (it runs on the old DX9 software and I'm still quite new to it's handling)... I was running my model on an old setting for a delta wing....so, maybe undoing what your steps state may help me get the reverse function in my model....
I'm having the same problem....maybe it's our transmitter's protocol....change the standard esc protocol from dshot to brushed, using a Naze flight control board and check..... It's night at my place, so once I'm done with things tomorrow, I'll try it out in our college
Can this run two 390 motors at once since it has 2 red and 2 black wires ?
My esc only has one black and red wire to connect to the motors, I bought 4 of them to use them as a motor for propellor for my ship, how do I connect them all together to the receiver? Or are they just independently
Yes. You can by connector.
Connect them all to the same channel with a splitter cable and be sure you remove all except 1 of the red wires or all if not using the BEC.
Nice
Tengo un motor 550 de un clon de tamiya Tl-01 y cuando le conecto este ESC al subir al maximo la potencia empieza a cortar ✂️ la energía y me descarga la batería muy rápido como si estuviera en "corto circuito". Lo interesante esta en que le conecto cualquier otro motor del mismo tamaño y funciona sin problema. No logro entender que pasa....
El motor consume mucho mas aperaje que este controlador??? O mi controlador venia dañado?? 🤔
This esc is junk it's way over rated from the specs it is rated at it should have ran my 15t motors on 3s no problem but it blew up in under a minute it was the second run . first was 2s then tried 3s and boom . it was in my clod buster . don't waist your money on this just get a hobby wing 880
Divide the current by 10 and it is good for that.
Junk indeed, 1 min and the magic smoke was free
I use 3s lithium ion battery and my esc blinking red light continuously
Will it take 4s lipo I had one that would take 4s lipo and I don't remember what brand it was
Not for long! You could try it if you do not use the onboard BEC by removing the red wire from the channel cable.
Can the reverse be disabled on the ESC you show?
I never try it. let's me check
I found with the Futaba 9C you can use a mix. Thro to Thro, -70% dn, +100% up, Offset 30%, Link off, Trim on. Reverse the throttle channel 3.
@@solarsynapse hi
Could you please elaborate? I'm kinda facing a problem with that.... mine's not going in reverse
@@animishaalagappa2327 My mix is to eliminate reverse.
@@solarsynapse so my radio is weird for me (it runs on the old DX9 software and I'm still quite new to it's handling)... I was running my model on an old setting for a delta wing....so, maybe undoing what your steps state may help me get the reverse function in my model....
Will that work on an 8 turn motor ?
Can i use 22.2 Volts (6s) 10000mah
Bu esc devresini 18 volt ile beslesem sorun olurmu
what lipos are compatible with this esc I just bought one and put on my budget emaxx
Yes. it support for lipo battery.
3S max.
Do you have a link to where you got that esc?
I could not find it myself
OK bro. I will drop buy link in video description. Sorry for didn't put it.
Is yours the two way esc
Yes it is
Can this ESC power 2 775?
It can
Literalmente hace 1 hora se me acaba de prender fuego ese esc al conectarlo a una 3s, casi quemo el voche y mi habitacion, no lo compreis
Can i connect outputs parallel and feed one bigger engine?
No, can not parallel ESC outputs together. Can parallel motors if ESC can provide enough current.
How distance work it bro
I use turbo remote, it can remote for 100 meters.
Can esc use 4s lipo batter
Sure. can use it
For 1 min, sure 😅
Can I connect 775 DC motor with same esc.
With servo also
Yes can. For servo we connect with receiver.
Okay, so mine ain't going to reverse for some reason.....
I think some versions don't have reverse. Can't go from forward to reverse directly if it has braking. Must brake to stop then can reverse.
@@solarsynapse mine apparently has a reverse function.... according to the product description
why my rc can't reverse😢 how tu reset the same esc
Can I know your ESC?
I'm having the same problem....maybe it's our transmitter's protocol....change the standard esc protocol from dshot to brushed, using a Naze flight control board and check.....
It's night at my place, so once I'm done with things tomorrow, I'll try it out in our college
How i can use 2 motor of 12v
Connect motors in parallel, you will have double the power draw.
can esc for dc 997?
It can use dc 997.
My esc can’t reverse?
I think your ESC one way, it's for helicopter. So it hasn't reverse function. You should find ESC for boat or car. Thanks!!
Resistente bien el agua
Its not 7.2-16?
It uses battery 7.2-16v
What is wrong with these people, afraid to talk, or don't know how?