DIY GMC Chevy Truck Back Glass Installation - How to Replace a Rear Window in a Silverado Sierra
ฝัง
- เผยแพร่เมื่อ 28 ก.ย. 2014
- Windshield Installation Kit on Amazon - amzn.to/2C0t1oF
3M 08693 Auto Glass Urethane on Amazon - amzn.to/2PBL78s
This video demonstrates the process I went through to replace the rear window on my 1997 Chevy K1500 pickup truck. The process covered in this video will be the same or similar on many other vehicles, Sierra, Silverado, Avalanche S10, Sonoma. This was my first attempt at replacing either a windshield or a back glass pane. Please leave questions or comments on how I could have done this better so others can learn from my mistakes.
Windshield Installation Kit on Amazon - amzn.to/2C0t1oF
3M 08693 Auto Glass Urethane on Amazon - amzn.to/2PBL78s
Click here to subscribe bit.ly/ngdysub1 and don't forget to select the notification bell!
Mark Jenkins is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com
Disclaimer:
Due to factors beyond the control of Mark Jenkins, I cannot guarantee against improper use or unauthorized modifications of this information. Mark Jenkins assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Mark Jenkins recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Mark Jenkins, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Mark Jenkins. - ยานยนต์และพาหนะ
Windshield Installation Kit on Amazon - amzn.to/2C0t1oF
3M 08693 Auto Glass Urethane on Amazon - amzn.to/2PBL78s
U can dry set the glass, once it’s perfectly in position, apply a long tape strip from the roof going down the glass. Do that several times. Leaving the tape applied to the glass you can “swing “ the glass out and set on the roof. Once glue is applied, simply “swing” the glass back into position.
Thank you for the crash coarse was perfect
Nice job! I have a leak in mine and I have been contemplating removing it and resealing it. You have shown me that the install is not difficult, thank you.
Lol same I got one small leak in the middle of my back windshield
my 2013 sierra just started leaking... did any of you guys follow the exact process? Don't know if I should clean everything like the uploader did
I'm going to be doing the same thing this weekend busted the back window out of my 98 Chevy loading up bunk beds
today used a oscillating saw with scraper blade to remove old urethane and glass on frame. worked excellent, going to try dow u428 primerless urethane to install window,
Did it work
This is the only video that is along these lines that actually goes into replacing the back glass. I’ve been unable to find diagrams of the trim on the back wall. I can’t remove the broken back glass until that is removed. This is a much more difficult project than you make it seem. Right now I am looking at having to remove the rear seats to access the trim to access the window, and it’s electrical connectors... here I was thinking I could just jump in the back and get the window out. Now I’m looking at a whole day doing it by myself...
did you figure it out
Helpful thanks
I got a buddy that's an auto Glazier and he has a tool which is specialty to his trade that's got a cylindrical aluminum handle about the size of 2 D batteries with a flat piece of Steel about a quarter inch wide sticking straight out of one. It's bent add a 90° angle and the tip of it if you will, does pointed and sharpened on two edges like a stiletto knife but it's only about 5/8 of an inch long is made specifically to remove the old urethane in that channel. He actually gave me one years ago and I have no idea what happened to it
Where did you get those tubes of urethane from and is that primer you put on necessary ? I’d appreciate your help as soon as you could. Thanks.
Thanks for the great video. Does anyone happen to know if the early 2k rear windows are interchangeable between the 1500 and 2500HDs? It looks like the will according to a couple places I've looked but I want to be sure before I buy the glass. TIA 😊
Nice job bro
Hey Mark, nice job on the window. I've talked with you before, I've got the same truck that I turned into a plow truck too, but one thing I did yesterday to mine is I installed a two battery system both are 850 CCA, and what a difference that makes as the plow and plow lights draw a lot from your battery, its very easy to hook up and your system will charge both batteries if hooked up the way I do it, I run two batteries in all my plow trucks hooked up this way. If you need this info just ask and I'll tell you how to run your cables......
***** Sounds good.
You get an heat gun to heat the tape up and pull out
Where did you get the chevy 3rd brake light?
can u put a link of the urethane kit I can not find it
You so much thank you
when you set yourwindsheild , some may require to use a setting block at the bottom so the glass doesnt touch metal. And always try to get a solid glueline up the oneside to all across top and down otherside to reduse leaks.
I got a Chevrolet Uplander in this hatch door the rear window I need to replace it and it's not showing video how to do that and you may know she's got a real thick rubber back there like Samsung kind of caulking or glue what can I use besides that
Can I have a link to the urathane kit on Ebay please
you don’t need nothing else that a knife to remove the glue, can save time and many steps !!
Normally you use a heat gun. To soften the seal
Love pppppp
0p try again what is it
Hi thanks for vid. I have a question about window glass. Was the replacement window completely flat or did it have curves at all on sides and along lower bottom edge? My truck had bed fire, and window busted, trim burned up, and I can't tell if the bottom edge and maybe side metal edges warped. If it did slightly warp, do you think that some bending or straightening of the metal edge, and lots of extra glue, would work? thanks
Most pickups are flat but may have a slight curve that you can’t really see unless looking up close. As long as the pinch weld(where the urethane touches the body) isn’t out of place too much you should be good. Back glass installations on a pickup are very forgiving as long as the glue touches both body and glass you should be good to go.
can you please give a link to the kit you purchased on eBay I didn't seem to find one like yours
+Mark Jenkins Hey thanks a mil for doing this, I'm seriously confident in doing this myself now possibly with the help of a friend or my old man to hold the glass, but this is sincerely appreciated. Several companies want to do this with no warranty and if I'm not getting a warranty I might as well do it myself...
were did you purchase the installation kit
The older ones all you needed was clothesline gojo and a dull regular screwdriver
We’re did you get the rear window seal
Can you please tell us how you got it out of the other pickup
Go to like lowes and get 2 foot of the smallest cable they sell its like pencil lead then I used 2 sticks for handles on each end so you got say like one of them things the mafia strangled people with lol then use a razor or knife to get a hole started in the seal then thread your cable threw it and use it like a saw around the perimeter of glass
@@themfnnitrorooster7619 great idea nice explanation
How long should it take if the window area is already cleaned up and all you have to do is put glass in and let it dry before driving?
at least two hours. please dont drive before that. the weight of glass will snatch that window out if you stop a little too quick. at least 2hours
YeSir...
I used a utility knife to remove strip an broken glass..the air tools look easier
How did you go about removing the glass from the other vehicle
He bought a new one from online.
How many inches is my rear glass window in my 08 Chevy Silverado
Don't know measure it duh ?
What glue did you use?
Jose Faustino urethane
No Rear Window Defogger in New Window?
Ejerce You buy the glu
Good job! Do you really need 2 Urethane tubes, or is one enough?? Is that primer important? Can you just use, clean it with alcohol?/ Thanks =)
Im an auto glass tech and aslong as you leave some of the old urathane on the body and dont gind down to the mettal the new urathane will bond better to the existing one and u just need to clean the glass with regular old windex and no primer on the glass is needed , primer is only needed if ur back glass has plastic on it since urathane dont bond with plastic , and u might be able to do it with one tube if it one small back glass like this one two tubes are required for bigger windshield hope this helped
@@adrianmarquez3415 Yes, thanks, I am replacing SIlverado rear glass to opening one, so one tube is enough?, and I dont need a primer, right? Thanks=)
@@Eeropolvasti if its a newer silverado with a power slider you will need primer otherwise your good .and yes one tube ,if you have some one to help you lay the glass in you can also just lay a nice even bead of glue around the edge of the glass leave about a quarter inch space around so it dont smear out when u push it in , and just grab it by the edegs when installing it,
Imagine if you just used the primer that came with. 😳
air chisel? why not use an oscillating multi tool with flat blade. clean up old window in 5 minutes tops
You should have let someone else video while u put the window in
You didn't rock test it?? After installation, you throw a 2 inch diameter rock at to make sure it bounces off.
Must be a technique used for Fords 😜😂 jk
Hahahaha 🤣🤣🤣🤣
#yourparents 😂
Brake parts cleaner
5:58 that sound is unbearable