Ahhh... The old days of B&W Photography, and DIY Image Development -> Circuit Board Fabrication! 😅 One idea, add a Couple "Registration Marks" to the Design - Dead Copper, that is used to mark one Corner, as your Reference Corner, for all your Gerber Files, or Circuit plus Component Layout Reference.
Thanks bạn.đã rất nhiều người làm líp.nhung líp của bạn hướng dẫn cho tôi cũng Như mọi người xem đang tim hiểu.học hỏi.nhung người thợ điện tử chắc họ không hài lòng lắm.vi bạn chỉ dẫn chú đáo.cảm ơn bạn
Good idea to make that automatic 12v battery charger at home, but a note: why force the red and green lights to take energy directly from the AC voltage? it is better to supply them with the DC 12V current by connecting the positive pin5 to the common relay pin 3, the red LED with a resistance of 1, 5k or 2KR between pin1 NC and GND pin4, and the green LED with its resistance between pin2 NO and pin4, or use only one resistor connected between pin5 and pin3, with the red LED placed between pin1 and pin 4 and the green between pin 2 and pin 4.Also it is possible to use a single double LED whose red pin is connected to pin1, the green pin connected to the pin2 and their common directed to GND pin4 via one current limiting resistor, while not forgetting a connection between pin3 and pin5 of the relay.
@@delanieacuesta4473 Hi, the charging voltage of an acid lead battery must be 20% more than the nominal voltage. For a 12 V battery the recommended charging voltage is 14.2 V. If you wish to use the 15 V transformer, it turns out suitable with its negligible difference of 0.6 V, however it is better to monitor the temperature to avoid a risk of overheating. The charging current is closely dependent on the storage capacity 'C' of the battery and must therefore have a value between 10 and 30% of C, so a battery of 7Ah will charge with a rate between 0.7A and 0.7 * 3 = 2.1A. As a proposal, if the capacity of your battery is 4Ah and you opt for a charging current of 30 per cent, the battery will charge from 1.2A, and to dissipate the surplus 3.8A, it is necessary to shunt the battery by a bulb 15V 60W. Otherwise, if the capacity is different you calculate the charge current according to the desired percentage and connect a load in parallel with the battery to absorb the excess current supplied by the transformer 🙂🙂
A similar but more sophisticated idea has already been used In order to charge the batteries for cars In the workshop I used a charger of its structure to be a power of 179 Amps I just have the play button press for playback And a power cutter Works on 220 volts when direct contact occurs between the poles after 3 seconds and cuts directly if a reverse battery is installed but does not interrupt while the engine is running Practically wonderful. I did not use to preach pieces with 2 LEDs But welcome any idea Just do not publish the wrong things I am from Algeria I always like to make things stronger, more effective and enduring Electronics is a very wide world Any idea may be the beginning of a project
12 volt battery with 16 volt cut off voltage ? that's bad man. as a IDEA kit is good. but actually it will ruin the battery. This cut off voltage actually depends on battery type. But anyway 16 volt can't be cut off voltage for 12 volt battery. To keep the battery healthy it's not correct. Anyway, good idea.
Yaar video aisi banao ke hum b project bana sakein.. itna sara taam jhaam humko milega bhi nhi market m Music ki jgh agar explain karoge toh sayad bhot accha hoga hamare liye. Video ka kya dekhna ab jb hamare layak isme kuch hai he nhi
Nice proyect! Just one thing... The cutoff voltaje must be little lower... In my experiense any lead acid battery cant be charged over 15v or they can explode
Exelente tuto rial pero puedo consultarte una pregunta ya hice el circuito pero a la hora de calibrarlo no me deja al votaje que nesecito quiere mas voltaje para hacer el corte y es arriva de 25v en este caso que tendria que cambiar para que pueda calibrarlo. Gracias Saludos!!
Nope, can be any current you want, the important part it must be centre tap type. 12 - 0 - 12 Volts. Even a 2 amp transformer would still make a useful charger.
porquè conectas la entrada de linea de CA a la placa de circuito impreso? no se supone que a la placa unicamente se aplica la salida reducida? es decir, los 12V ca? no me queda claro eso... :/
Ye sarkit camplit mukhe mil sakta hai kya 12v 40amp betry ke liye palese batanaa ya complit with transfarmar
Thank you very much and very good🌷🌷 🌷
Ahhh... The old days of B&W Photography, and DIY Image Development -> Circuit Board Fabrication! 😅
One idea, add a Couple "Registration Marks" to the Design - Dead Copper, that is used to mark one Corner, as your Reference Corner, for all your Gerber Files, or Circuit plus Component Layout Reference.
It is very nice to share a desulfator circuit construction video to solve the health of your hand
Excellent Job sir well done
#NSElectronics
This project is very good!
This is amazing...... keep it up....Cheers from Bigganbaksho
That was really good that. I subscribed!
Is the printed paper just normal stationary paper or something specially made for that cercuit board making
rilo ariicho ariicho not cercuit is circuit
Its a heat toner transfer paper for pcb
I think it's glossy paper
Charging 12v battery to 16.5v? Are you serious, one time charge? :D
Very Nice, I was about to throw out my old charger, but I think I'll try this first
Thanks bạn.đã rất nhiều người làm líp.nhung líp của bạn hướng dẫn cho tôi cũng Như mọi người xem đang tim hiểu.học hỏi.nhung người thợ điện tử chắc họ không hài lòng lắm.vi bạn chỉ dẫn chú đáo.cảm ơn bạn
Excellent job my brother
What is the brown liquid you used
Where do you get this same print.
We wanted this as its a good product
Good idea to make that automatic 12v battery charger at home, but a note: why force the red and green lights to take energy directly from the AC voltage? it is better to supply them with the DC 12V current by connecting the positive pin5 to the common relay pin 3, the red LED with a resistance of 1,
5k or 2KR between pin1 NC and GND pin4, and the green LED with its resistance between pin2 NO and pin4, or use only one resistor connected between pin5 and pin3, with the red LED placed between pin1 and pin 4 and the green between pin 2 and pin 4.Also it is possible to use a single double LED whose red pin is connected to pin1, the green pin connected to the pin2 and their common directed to GND pin4 via one current limiting resistor, while not forgetting a connection between pin3 and pin5 of the relay.
Thanks for comment, It is easy way connecting Two led from AC voltage.
Because Indians have no security awareness
@@hoho-xw3jt really? I hope its not the case
Hi can i ask something if it's ok to use 15V 6A transformer to make a 12V battery charger like this?? Thank🙂🙂
@@delanieacuesta4473 Hi, the charging voltage of an acid lead battery must be 20% more than the nominal voltage. For a 12 V battery the recommended charging voltage is 14.2 V. If you wish to use the 15 V transformer, it turns out suitable with its negligible difference of 0.6 V,
however it is better to monitor the temperature to avoid a risk of overheating. The charging current is closely dependent on the storage capacity 'C' of the battery and must therefore have a value between 10 and 30% of C, so a battery of 7Ah will charge with a rate between 0.7A and 0.7 * 3 = 2.1A. As a proposal,
if the capacity of your battery is 4Ah and you opt for a charging current of 30 per cent, the battery will charge from 1.2A, and to dissipate the surplus 3.8A, it is necessary to shunt the battery by a bulb 15V 60W. Otherwise, if the capacity is different you calculate the charge current according to the desired percentage and connect a load in parallel with the battery to absorb the excess current supplied by the transformer
🙂🙂
Congratulations on the design ... what paper used to make the phenolite plate
Useful project
Thanks friend
Obrigado professor o seu trabalho
é muito criativo !!!!!!
You are youtube partner!
woo ! very nice friend thank for your idea.
Thanks for watching
Good idea
Thanks you
Hi
The coolest part was you making the circuit board
A similar but more sophisticated idea has already been used
In order to charge the batteries for cars
In the workshop I used a charger of its structure to be a power of 179 Amps
I just have the play button press for playback
And a power cutter
Works on 220 volts when direct contact occurs between the poles after 3 seconds and cuts directly if a reverse battery is installed but does not interrupt while the engine is running
Practically wonderful. I did not use to preach pieces with 2 LEDs
But welcome any idea
Just do not publish the wrong things
I am from Algeria
I always like to make things stronger, more effective and enduring
Electronics is a very wide world
Any idea may be the beginning of a project
Wich paper use to print
wow very good ..
12 volt battery with 16 volt cut off voltage ? that's bad man. as a IDEA kit is good. but actually it will ruin the battery. This cut off voltage actually depends on battery type. But anyway 16 volt can't be cut off voltage for 12 volt battery. To keep the battery healthy it's not correct. Anyway, good idea.
Yaar video aisi banao ke hum b project bana sakein.. itna sara taam jhaam humko milega bhi nhi market m
Music ki jgh agar explain karoge toh sayad bhot accha hoga hamare liye. Video ka kya dekhna ab jb hamare layak isme kuch hai he nhi
this circuit board is very nice. all charging Auto cut off circuits are cut secondary bolt but this circuit cut off the primary. save electricity.
It's a clever circuit. A bit clunky but would work well, and once finished everything is turned off
How hard would it be to make it trickle charge instead of cutting off completely my friend? Thanks for starting the music over every time it quit!😉
Tôi là người đang cầm học hỏi và khám phá về điện tử.hiện tại tôi mù mịt.xem bạn làm.và học tập.cảm ơn bạn
Circuit provides kra sakte hoo ji or kitne ka hae complete circuit
Good what types you are using to do this
Were is the switch in the circuit diagram
COOL, VERY GOOD. WHAT NAME OF THIS PRINTING PAPER
Very Good Video 👍
Bonjour . très belle vidéo merci de ce partage. Quel papier utilez vous pour inprimer le circuit imprimé. Merci
Sir can i use this project for a 100 Ah battery🙏🙏
Very good your project, congratulations on the achievement, thank you for sharing your ideas with us,
hello sir..good day..can i use this charger to 100Ah bateery?
Yeh kaha milenge aur kya prices h
Can I use this to charge a 12v motor cycle battery?
شكرا.. انا مهتم جدا بالموضرع
ماهو هذا الورق المستخدم استاذ ميلود ؟؟؟
Mantaff bro video nya and kreatif 👍👍👍👍
សួបន្តិច បងជាជនជាតិខ្មែមែនបង
បាទខ្ញុំ ជាជនជាតិខ្មែរយើងតើ!
Great job, congratulation 👏🏽👏🏽👏🏽💯
সার্কিট বোর্ড পিসিবি তৈরী কিভাবে করবো - কি ক্যামিক্যালে কপার ওয়ার তৈরী হয় বলবেন ! সুপার জব ॥ অসংখ্য ধন্যবাদ ॥
excellent video
good idea
What is the current passing through thise circuit ؟؟
Very impressive...bravo, sir!
very nice
Thanks for watching
Like it, thanks for the video :)
Very good sir love you 👏😂
Thanks for watching
What kind of paper did you use to print the circuit?
Thermal paper
What type of paper is used for the pcb
very good..........!!!!!!!!!!!!. thanks
Nice proyect! Just one thing... The cutoff voltaje must be little lower... In my experiense any lead acid battery cant be charged over 15v or they can explode
good video
Exelente tuto rial pero puedo consultarte una pregunta ya hice el circuito pero a la hora de calibrarlo no me deja al votaje que nesecito quiere mas voltaje para hacer el corte y es arriva de 25v en este caso que tendria que cambiar para que pueda calibrarlo. Gracias
Saludos!!
Que tipo de papel es ese donde se imprimió??
PCB paper, i have order from banggood website. thanks for watching
There's no pcb layout to down load in the link you wrote👇 anyway thank you for this tuturial. We can copy the diagram.
Cirkit radio made mil sakti hai kya agar mil sakti hai to nam bataye air transfal kitne wat ka hai
hello all right friend you could tell me what kind of paper you use and what laser printer or ink?
subscribed☝☝👍👍👍👍
Lead acid 14.7volt full charge not 16.5volt, deep cycle batteries full charge on 14.4volts, the sensor voltage should be right on the battery
Is that aDIY mini drill??
Does it have to be a 10a transformer????
Nope, can be any current you want, the important part it must be centre tap type. 12 - 0 - 12 Volts.
Even a 2 amp transformer would still make a useful charger.
which type of paper are you using for laser print?
Is it possible to place an LCD panel in this circuit and two buttons to enter the battery voltage cut-off numbers? Thank you
Your link isn't working to the PCB board and Circuit.
បងអ្នកខេត្តណាដែរ.? សុំលេខមួយផងបានដែរអត់..
Siem Reap
What is the range of input AC voltage
Circuit ko pen copy me samjhaiye sir
ola boa noite amigo,muito legal seu video parabens gostei muito,como posso fazer o download da pcb por favor me ajude
Nice circuit
Can do auto cut circuit for 60 to 70 volts
hello sir, what paper are you using? on which to attach the circuit diagram.
Awesome Edea
Download nhi ho raha hai apke web jake dekha to nhi hai
For 12 V Battery To Keep it Healthy For Long Time Keep cut off in 14.5 V ... search for an alternative to switch to make it practical circuit
porquè conectas la entrada de linea de CA a la placa de circuito impreso?
no se supone que a la placa unicamente se aplica la salida reducida? es decir, los 12V ca?
no me queda claro eso... :/
good one.....every full charge we need to reset again. can you to change the reset in auto mood. like a defult value 9v,10vdc...
Can i use it for 6v battery
Nice friend
Thanks for watching
Excuse me, why can't the circuit cut off the electric? Is there any problem? I'm using 3A non CT Transformator with 20v output
Nice video
Thanks for watching
what kind of paper do you use to transfer to a copper plate
4 battery 1baar me charge ho ga keya
নাইচ ভিডিও
good show. thank you
the control by thyristor its better because will not booilng the battery can u share drawing
No esta el link de descarga esta caido lo puedes subir nuevamente gracias desde Mexico.
Sir pls share the all register value with half and quarter watt register 1/4 &1/2
How to make circuit PCB please details
Bhai ek aisa bhi charger banaye jo cut na ho grevaty ghat jane ke bad Bahut dikkat hota h
is 16.5 volts the right voltage for a full charge battery? is this voltage over the charging limit? what i know is 14.7 volts
VC é muito bom isso
Thanks very much !!!!
Is that a 110 v or 220 v for line in
220v
Which pcb design app
Diptrace pcb software