I just want to say thank you for all the videos you make public. This has been a game changer for me. I work for a very successful company in my area who has almost no training and I don't know how they are still in business after all I have learned from you vs what they know and teach. I listen to these videos all day every day between service calls and this has greatly improved my skills, my service, and im sure every client I go to would thank you as well.
Another great video from Craig, but to simplify things on the Uniweld 1/4 / 5/16 / 3/8 combination bender, on the movable head you will see: 0, R, and L. The R and L marks are used to line up with your mark on the tubing. If your measurement is coming from the LEFT of the tube going to the right, measure and make your mark and insert the tube into the LEFT of the bender, like Craig does, Line up your 0's and adjust your tube so the mark you made lines up with the L while keeping the 0's aligned, and make your bend. The R is for bending from the RIGHT side of the bender using the same procedure.
Kevin, you are absolutely correct! I just teach in the one direction because I always found that students would get confused as to the direction of the bend so I would always say it will follow the moving arm of the bender and then if they moved to the larger lever benders, there were no marks, thanks!
Craig, as always, great video. I was wondering if you could demonstrate how to do a double bend using the ratcheting crossbow bender like you need to do when bending tubing on the outside of a home when connecting the tubing to the condenser (two left bends, first bending the tubing up that will meet the condenser tubing swedged stubs, then bending the tubing down that will hug the outside wall). Thank you and thanks again for all of your great videos!
I have used the spring bender on the inside of the pipe with no issues. Good to know it works on outside as well. Only difference I guess is it can get stuck putting it inside but there is zero chance of over bending it.
@HoodHandyman you said you put it on inside. How you gunna get it out? Why would you put it on the inside? They come in all different sizes to go on outside of your tubing. Better off buying a proper bender though either way
@@HVACRTECH-83 I just stuck it in bent the pipe and pulled it out the springs move its really not that hard . Works great for small bends on the ends of the pipe
As always, I get something from every video I watch. My problem is a lack of basic education on things it would be assumed I know already. My AC experience comes from the automotive industry. Going to the very basics of an installation, is there a video on proper running and installation of the line sets, what to avoid and why one setup might be better than another? Thanks.
As always, a well thought out video with lots of important information. My only question is how do you know if you have "soft copper"? I just bought a 3/8 3/4 Streamline line set. I assume that it is soft copper, but how can I know that for sure?
Craig, I have another question: if you don't want the bender to flatten out the tubing as it bends it could you slide a bending spring over the tubing and then use a larger mandrel and stationary bar?
Craig, I was wondering how the ratcheting crossbow bender can bend tubing if one end of the tubing is anchored such as when it's attached to the condenser or evaporator. I understand that this type of bender makes the bend by driving the tubing up between the guides on the stationary bar and that the bar's guides pivot to allow this to happen. Also, when you're bending a piece that isn't attached to anything both ends of the tubing are shortened to allow the tubing to be bent. So, if one end can't move how does the tool accommodate for that? Does the tool turn until it reaches a point where it can slide along the anchored piece of tubing? Somethings gotta give, right? Thank you.
Do you have any advice on how to get a compression nut onto a copper pipe that's been bent by hand? Seems bending put just enough imperfections in the tube to prevent the nut from fitting on.
Have u had to bend copper tubing that's already installed on the ground this a 1" water copper tubing that's on the ground if u have please let me know if u have a video n how can I find it... Thanks Joe
The workbook has 1,000 questions and the answers in another packet that comes with the workbook. Both the book and workbook are available at www.acservicetech.com/store and also on amazon, thanks!
@@acservicetechchannel hahahaha!! Wasn’t a slam on you bro. I know how it is!! I was just excited that you had this video loaded up, probably before I mentioned it… good stuff! Sent video to coworkers, thanks again for all your detailed hard work!!
Do they make a commercial type bender for very small tubing [2.5mm] diameter Copper & Brass tubing. I’ve got a Hobby type now, curious if they make a better tool…
So I've had a few circumstances where I had to build a new coil. On a refrigeration unit where the line comes out of the condenser coil, it then goes into the condensate tray, which may have water. The coil is a serpentine, that is, a bunch of 180 degree turns, could be 3/16 to 1/4" copper tubing. I have never been able to make clean bends. Is there a way to do this without having some kind of special mandrel? Jim
I would just use that 1/4" 5/16" 3/8" manual lever bender. I used to have students make something like that in the classroom with 1/4" to exact measurements in order to gain the skill of the bending tool, thanks!
Unfortunately some ratchet bender do not have the 2 markings to line up on the half moon. Any ideas for my KS TOOLS bender to measure properly. And as well can you also show how to measure for a 45⁰ bend on the ratchet bender? Thanks a lot advance!
Agreed, the plastic road is my choice too when near the end of the pipe. But when further away I use the methods in the video. Excellent video thank you.
I have a question, I bent a pipe with diameter of 18 with 1mm in "meat" with o similar tool, I didn't end up bending it up to 90' because the pipe made creases and it even broke, the same happened with a pipe of 15 by 1mm in "meat",..I mention that the pipe of 18 and 15 was not from the pipe to the coil but from straight pipe. The question is why or creased and even or torn? It probably can be cause of 1mm thickness in "meat"?? Or the copper pipe to the coil is softer, more malleable?? I can have the same problem with pipe to coil whether it is 18 or 15 if in "meat" is 1mm??..I would be happy if would you answer me....Thank you very much for the answer
once u make a 90 degree bend, can we bend the copper pipe back without issue possibly with hand or bender? (i've heard ppl say copper pipe can only bend once and they get a bit hard to bend after)
The tubing we use is considered "ACR" air conditioning refrigeration tubing which is usually soft copper and comes in a roll with either rubber or plastic caps on the ends. It is tempered to bend well. If it is in a roll, it is soft copper tube, thanks!
Don't use that cross bow bender for 1 1/8 ever. They can't handle it. Plain and simple. Mine was a few months old I was making a bend up 25 ft on extension ladder and the whole body of the bender shattered in my hands,just about fell of the ladder and my hand was mangled up so bad bleeding all over the customers siding, I couldn't finish the job. So just don't do it
I wish I could find a clear explanation of the R Mark on the small 3-size lever bender.....everyone says use L coming from left and R coming from right but that DOES NOT work with the R, it's always off and seems to be the exact length off of a sledge stub
Machine bending the best..my 5 year apprenticeship all those years ago was the way to learn. Something many cant do these days..so its a hand full of elbows or plastic 🙄
Some soft copper (ACR) may not have been tempered correctly. I have run into that quite a few times before but most new rolls are good for bending, thanks!
I just want to say thank you for all the videos you make public. This has been a game changer for me. I work for a very successful company in my area who has almost no training and I don't know how they are still in business after all I have learned from you vs what they know and teach. I listen to these videos all day every day between service calls and this has greatly improved my skills, my service, and im sure every client I go to would thank you as well.
That is so awesome to hear! Thank you very much for taking the time to write this note!
Its because of you my customers love the installs I do and the workmanship
Great detail on how to align the pipe in the bender. I’ve always been hit & miss on accuracy.
Thanks a lot Roger!
This is such a great resource that I refer back to time and again.
Another great video from Craig, but to simplify things on the Uniweld 1/4 / 5/16 / 3/8 combination bender, on the movable head you will see: 0, R, and L. The R and L marks are used to line up with your mark on the tubing. If your measurement is coming from the LEFT of the tube going to the right, measure and make your mark and insert the tube into the LEFT of the bender, like Craig does, Line up your 0's and adjust your tube so the mark you made lines up with the L while keeping the 0's aligned, and make your bend. The R is for bending from the RIGHT side of the bender using the same procedure.
Thanks for that, I was going to ask the question but you've answered it very well thanks. Excellent video as usual thanks.
Kevin, you are absolutely correct! I just teach in the one direction because I always found that students would get confused as to the direction of the bend so I would always say it will follow the moving arm of the bender and then if they moved to the larger lever benders, there were no marks, thanks!
Thank you, I am still confused by the R mark....
Don't you have to add gain if you use the R mark?
Craig, as always, great video. I was wondering if you could demonstrate how to do a double bend using the ratcheting crossbow bender like you need to do when bending tubing on the outside of a home when connecting the tubing to the condenser (two left bends, first bending the tubing up that will meet the condenser tubing swedged stubs, then bending the tubing down that will hug the outside wall). Thank you and thanks again for all of your great videos!
Nice video Craig! Didn't really know how to measure accurate the bend, good work!
Glad to help Manos!
I have used the spring bender on the inside of the pipe with no issues. Good to know it works on outside as well. Only difference I guess is it can get stuck putting it inside but there is zero chance of over bending it.
Those are designed for use on outside of tubing only lol
@@HVACRTECH-83 works on outside too trust me
@HoodHandyman you said you put it on inside. How you gunna get it out? Why would you put it on the inside? They come in all different sizes to go on outside of your tubing. Better off buying a proper bender though either way
@@HVACRTECH-83 I just stuck it in bent the pipe and pulled it out the springs move its really not that hard . Works great for small bends on the ends of the pipe
@@HoodHandyman hey, whatever works forya.
I really like and understand the way to use my hands bender when i watched this video🙏🙏
I was thought maybe you had deductions to use like when bending conduit. But measuring center to center works too. Thanks for the video.
I am just trying to keep it simple for everyone, thanks!
As always, I get something from every video I watch. My problem is a lack of basic education on things it would be assumed I know already. My AC experience comes from the automotive industry. Going to the very basics of an installation, is there a video on proper running and installation of the line sets, what to avoid and why one setup might be better than another? Thanks.
The best hvac channel
As always, a well thought out video with lots of important information. My only question is how do you know if you have "soft copper"? I just bought a 3/8 3/4 Streamline line set. I assume that it is soft copper, but how can I know that for sure?
Craig, I have another question: if you don't want the bender to flatten out the tubing as it bends it could you slide a bending spring over the tubing and then use a larger mandrel and stationary bar?
Craig, I was wondering how the ratcheting crossbow bender can bend tubing if one end of the tubing is anchored such as when it's attached to the condenser or evaporator. I understand that this type of bender makes the bend by driving the tubing up between the guides on the stationary bar and that the bar's guides pivot to allow this to happen. Also, when you're bending a piece that isn't attached to anything both ends of the tubing are shortened to allow the tubing to be bent. So, if one end can't move how does the tool accommodate for that? Does the tool turn until it reaches a point where it can slide along the anchored piece of tubing? Somethings gotta give, right? Thank you.
Do you have any advice on how to get a compression nut onto a copper pipe that's been bent by hand? Seems bending put just enough imperfections in the tube to prevent the nut from fitting on.
Out of all the benders which os the best and easiest to use
What is the tightest radius bend of 180 degrees you can bend using 1/2 inch copper water pipe fella ?? Thanks
Excellent video...Much the same in bending conduit...I'm glad I found this site...Thank you.
Awesome, thanks Vern!
Very good video I love to have the copy of your books
You should buy it. Best investment I made when I started off in the field.
They are available on amazon and at www.acservicetech.com/store thanks!
That's only for soft cooper tube? Do you have a video for hard copper? Thanks
Yes. Can you torch hard copper to anneal it?
You can’t bend ACR copper
Very useful tutorial sir. Liked!
Finally ; Thank you so much.
Glad to help Robin!
Have u had to bend copper tubing that's already installed on the ground this a 1" water copper tubing that's on the ground if u have please let me know if u have a video n how can I find it...
Thanks
Joe
Excellent work,.. I learn so much today thank you so much
Outstanding as usual Thanks!!
Awesome!
Excellent video.
Thank you Roland!
Craig, why did the bat get hit crossing the road?
Great details!!!. does the book have review questions on each chapter? On the workbook
The workbook has 1,000 questions and the answers in another packet that comes with the workbook. Both the book and workbook are available at www.acservicetech.com/store and also on amazon, thanks!
Haven’t even gotten through the commercials. Love ya!!?
I don't have control of the timing of the youtube commercials. Google/TH-cam places the amount and when, thanks and sorry!
@@acservicetechchannel hahahaha!! Wasn’t a slam on you bro. I know how it is!! I was just excited that you had this video loaded up, probably before I mentioned it… good stuff!
Sent video to coworkers, thanks again for all your detailed hard work!!
Great video.
Thanks Phil!
@@acservicetechchannel Sure
Outstanding!!! just what I needed.
Thank you, Craig.
OMG YOU MADE IT LOOK SO EASY. THANKS
Happy to help!
Do they make a commercial type bender for very small tubing [2.5mm] diameter Copper & Brass tubing. I’ve got a Hobby type now, curious if they make a better tool…
Nice work
Thanks Lance!
Please thank you for the video,have learnt a lot from the u
I ordered the paper back and Workbook… 😃👍
But are you gonna make a book about installation?
I may make one in the future and thanks for letting me know what you would like to see!
What model/brand is the racheting tube bender
So I've had a few circumstances where I had to build a new coil. On a refrigeration unit where the line comes out of the condenser coil, it then goes into the condensate tray, which may have water. The coil is a serpentine, that is, a bunch of 180 degree turns, could be 3/16 to 1/4" copper tubing. I have never been able to make clean bends. Is there a way to do this without having some kind of special mandrel?
Jim
I would just use that 1/4" 5/16" 3/8" manual lever bender. I used to have students make something like that in the classroom with 1/4" to exact measurements in order to gain the skill of the bending tool, thanks!
Unfortunately some ratchet bender do not have the 2 markings to line up on the half moon. Any ideas for my KS TOOLS bender to measure properly. And as well can you also show how to measure for a 45⁰ bend on the ratchet bender? Thanks a lot advance!
Just add a few extra inches of pipe. make the bend then mark the pipe at the desired length and cut off the extra.
Thank you, Thank you, Thank you,
Glad you enjoyed it!
We use the internal plastic rod pipe bender , looks a lot easier than the spring and it’s also 1.5m long or longer
Agreed, the plastic road is my choice too when near the end of the pipe. But when further away I use the methods in the video. Excellent video thank you.
@@tonysavage8364 I like the internal because : firstly most pipe being pre insulated, Also inaccessible spots, hole through the wall /bend
Do you have a link for this type of bender?
Thanks for mentioning that type Nathan!
Link to :
polybender.com.au/
thank you teacher
Thank you!
Great stuff. Thank you!
Thanks a lot Chip!
Your Books any available in online 😺 please tell i buy this book immediately 🙋💯
you're the best man
You're AMAZING 👍
I have a question, I bent a pipe with diameter of 18 with 1mm in "meat" with o similar tool, I didn't end up bending it up to 90' because the pipe made creases and it even broke, the same happened with a pipe of 15 by 1mm in "meat",..I mention that the pipe of 18 and 15 was not from the pipe to the coil but from straight pipe. The question is why or creased and even or torn? It probably can be cause of 1mm thickness in "meat"?? Or the copper pipe to the coil is softer, more malleable?? I can have the same problem with pipe to coil whether it is 18 or 15 if in "meat" is 1mm??..I would be happy if would you answer me....Thank you very much for the answer
once u make a 90 degree bend, can we bend the copper pipe back without issue possibly with hand or bender? (i've heard ppl say copper pipe can only bend once and they get a bit hard to bend after)
What is the R and L on the lever bender and what are they used for?
these are ok to use on potable copper water lines correct?
Thanks!
Nice. Thanks
New and useful information
Wow, good. Tks
Thanks a lot!
How do you know it is soft copper?
i had the same question.
Because you can bend it.
Typically at least where I'm at, soft copper is sold in a roll, whereas hard copper is sold by the stick.
@@nelsoncody38
Thank you for a good answer.
I deal with water copper lines.
Never notices any markings. Never shopped for the rolls of copper.
The tubing we use is considered "ACR" air conditioning refrigeration tubing which is usually soft copper and comes in a roll with either rubber or plastic caps on the ends. It is tempered to bend well. If it is in a roll, it is soft copper tube, thanks!
Very nice
Thanks!
The tubing Bender shows its unavailable do you have another source?
Don't use that cross bow bender for 1 1/8 ever. They can't handle it. Plain and simple. Mine was a few months old I was making a bend up 25 ft on extension ladder and the whole body of the bender shattered in my hands,just about fell of the ladder and my hand was mangled up so bad bleeding all over the customers siding, I couldn't finish the job. So just don't do it
What were you bending emt?
@@Sak-zo1ui not funny actually. But no soft copper lineset
@@HVACRTECH-83 it wasnt a joke. Dont be so sensitive.
@@HVACRTECH-83 you're right they cant handle that thickness but it shattered like that because its a Crossbow 😂 is it cheap? I never heard of it
Was your bender made in china ?
It's Just amazing
Would you please tell me how i get that
I am from Bangladesh
Good info
Awesome tool . Many thanks
Thanks Hung!
Where can I get the tool to do the lines on shitmetal?
I wish I could find a clear explanation of the R Mark on the small 3-size lever bender.....everyone says use L coming from left and R coming from right but that DOES NOT work with the R, it's always off and seems to be the exact length off of a sledge stub
Machine bending the best..my 5 year apprenticeship all those years ago was the way to learn. Something many cant do these days..so its a hand full of elbows or plastic 🙄
Knowledge is power so take it all it. That's awesome to hear that you learned so much during that apprenticeship course!
How to bend the same tube (1/2") to different diameters? example: 17" 15" 13" 11", is it even possible?
Very good sir. Iam from iraq
What is your preferred bender. Thanks great videos thanks.
I prefer the lever benders but often they are just too long for the application, thanks!
Thank you 👍👍👍🤝🤝🤝
Hey I from India I am interested this job I have 2 year ac technician experience
It is really a great trade!
@@acservicetechchannel send me invitation letters
bending springs, slightly overbend your angle, then bend back. Your spring will fall off like an old mans wedding ring.
From Indonesia
Awesome, thanks!
7:05 creepy third hand…. 😂
Ha ha, yup!!!
My hand bending technique is definitely not cutting it. 😂
I hand bent for years, its all good!
@@acservicetechchannel thats what i was looking for 😍
How much
Great 👍🏻 hindi meanings
How to straight a copper pipe
👍
Hi
Bending copper pipe for plumbing will get weaker on angle that can easily erosion by calcium that lead pipe leak
Modern recycled copper tubing does NOT bend without kinking.
Some soft copper (ACR) may not have been tempered correctly. I have run into that quite a few times before but most new rolls are good for bending, thanks!
If you're using ACR tubing, it must be annealed with heat before you can bend it. Be sure to flow nitrogen.
@@markcarpenter3600 can’t wait to hear the installers moan when I bring that up at the next meeting. Lol
I hate that cheap cross bow bender it sucks ! Would not recommend that one I got the Hilmar one haven’t had a single problem with it
এরকম ব্যান্ডের আমার একটা লাগবে কোথা থেকে আনা যায় বা কিভাবে আনা যায় পুরা সাতটায় আমার লাগবে কত দাম
Hii
🙏👌👌👌👌👌👌👌👌
The pipe rippled...
India me available
In hindi
🍺🥃😐👍🏻
Thanks a lot!
Excellent video
Thanks Tank!
Nice work