Once again a real how to do it video with complete , detailed instructions...no bullshit, no sales hype, just real instructions by people who have actually done the work. Thaanks again..!
I just replaced the fresh air inlet hose on my 2015 435i. Removal of the fan assembly gave me plenty of room to install the pipe. For the M10 bolt at the turbo, I used a long 1/4” extension and fed it through above the water pump motor.
Love how thorough your videos are. Huge resource for BMW owners although your absolute best video of all time was the rear wiper delete on the Porsche 993 911 😂 Keep it up!
Looking to install the same parts this weekend. Along side of the Diverter valve and turbo inlet going to do a coolant change, thermostat hose/flange upgrade, and boost pipe as well. Hopefully with the coolant change I'll just rip the 2 hoses right out. I also have a oil catch can as well so the breather line hopefully is easier for me since it is already detached from my engine.
I'm not sure if it is different spec'd M2s. I'm in Canada and my 2018 LCI M2 the "T20" screw holding in the breather pipe is a "T25", very important to check how the screw fits, I almost stripped the T25 using a T20 bit and realized something was not right, checked with a T25 and out it comes. I did it a bit differently, ripped out the turbo inlet to almost an out position and just got to it with a 1/4" ratchet with no extensions. Granted my other side of the breather hose was disconnected from the engine already as I have an oil catch can.
Did you get the inlet to sit perfectly flush on the coupling near the turbo? I noticed on yours and mine I can't fully slide it on because of the 10mm nut and stud
Appreciate the video. I completed the job in 7.5 hours. Without your guidance this would have been 2x harder. Thank you. Putting o ring lube helped a lot. Grinding the Allen was a no go. Your method worked with long ball head hex. I turned it and used regular Allen to do final tightening. Again, really really appreciate the video.
+LOUIS V so you watched an entire detailed install video when all you wanted to hear was revs? You didn’t think about skipping to the end? I think this one is on you 😂
Once again a real how to do it video with complete , detailed instructions...no bullshit, no sales hype, just real instructions by people who have actually done the work. Thaanks again..!
+Bob Fognozzle thank you!
I just replaced the fresh air inlet hose on my 2015 435i. Removal of the fan assembly gave me plenty of room to install the pipe. For the M10 bolt at the turbo, I used a long 1/4” extension and fed it through above the water pump motor.
+@randyhayward9880 thanks for the additional info! 🍻
Love how thorough your videos are. Huge resource for BMW owners although your absolute best video of all time was the rear wiper delete on the Porsche 993 911 😂
Keep it up!
😂 😂 😂
Great Video! I need to get a BOV for my n55!
+Evan Goyuk you are really going to love this one then 😁
Looking to install the same parts this weekend. Along side of the Diverter valve and turbo inlet going to do a coolant change, thermostat hose/flange upgrade, and boost pipe as well. Hopefully with the coolant change I'll just rip the 2 hoses right out. I also have a oil catch can as well so the breather line hopefully is easier for me since it is already detached from my engine.
+Sofa King good luck! 👍
Thanks for the info, that is very helpful!
+Lai Jiang you’re welcome 🍻
Pain in the ass when I put mine in. Took me 30 min.
+Cuttthroat Performance sounds right 😆
HOLY SHIT what a pain in the ass this is!! Thanks a lot BMW lol
+TheRealSalami 😂 😂 😂
Thanks so much for this! Subscribed 😄
+Evans Tampubolon you got it!
Just installed mine inlet and it took me 6 hours, never going to do it ever again
+@shhhlongdeek2921 but you did it! 😆
I'm not sure if it is different spec'd M2s. I'm in Canada and my 2018 LCI M2 the "T20" screw holding in the breather pipe is a "T25", very important to check how the screw fits, I almost stripped the T25 using a T20 bit and realized something was not right, checked with a T25 and out it comes. I did it a bit differently, ripped out the turbo inlet to almost an out position and just got to it with a 1/4" ratchet with no extensions. Granted my other side of the breather hose was disconnected from the engine already as I have an oil catch can.
+Sofa King thanks for the info!
Little off topic but those 'jacks' you lift your car with what brand are they? Thanks for great video!
+John Bünsow Linden the QuickJack?
Si es para hacerlo en Costa Rica escríbame para que no le traveseen el N55
INSTALLATION GUIDE BLOW OFF VALVE KIT M2 FMDVF22A
For top hose...Use 4 dimes to put between the the clamp and it should release.
+Marc that works, huh? Very interesting. Thanks for the tip!
Can a turbo valve be installed with a air intake?
Hey I had a question. Do you think if you cut down the 5mm Allen key that it would have worked with a lower profile?
+Andrei Bogdan maybe. Let us know if you try it!
@@HelpMeDIY I will report back my findings tomorrow. Doing the installation then.
Did you get the inlet to sit perfectly flush on the coupling near the turbo? I noticed on yours and mine I can't fully slide it on because of the 10mm nut and stud
@@NoCompM2 what you see is all I remember since it wasn’t my car
Appreciate the video. I completed the job in 7.5 hours. Without your guidance this would have been 2x harder. Thank you. Putting o ring lube helped a lot. Grinding the Allen was a no go. Your method worked with long ball head hex. I turned it and used regular Allen to do final tightening. Again, really really appreciate the video.
I’m doing this in my garage right now. I’m currently removing the stock diverter valve and on 4 occasions so far you’ve said the wrong sizes
+J B sorry if that’s the case! Is it possible yours were different? Hope you still found the video helpful.
Can you install the BOV in any direction?
+Luis Vargas that I don’t know for sure so maybe someone else can chime in
Wow what a waste of time...waited all this time and you couldn’t even do some revs!
+LOUIS V so you watched an entire detailed install video when all you wanted to hear was revs? You didn’t think about skipping to the end? I think this one is on you 😂