@@dndon2007 k ill wait untill someone in the states get them alliexpress has burnt me to many times i wont order on there anymore . But thank you much appreciated
@@jayward7536 I had many orders from aliexpress all the order went very slow in processing and shipping but when I order the jumper t16 from jumper store it takes only one month to delivered to me here in Saudi Arabia.. maybe grayson hobby will sell this board soon because they are sell jumper stuff in usa.. 👍
@@dndon2007 yea im sure they will have it . I can wait not that big of a deal is a nice little uprade for my t16 pro . If i get it from ali it takes like 2 months lol
Where can we get the charging board? I want to install one into my T16, and perhaps my PowerPLAY with my printed back shell that makes it run off 18650's, Thingiverse 4080213 I have a USB 2S balance charger that came with a cheap RC car from Banggood, I discovered during testing it was actually a 1S charger that swapped which cell it was charging every few seconds. I'm really curios to test this one.
@Gal Kremer Thanks, I've just ordered 3 charging boards from that link you provided. Because Jumper released the 3D model of their T16, I can modify the top plate for the USB-C socket and print a new one rather than melt the existing one. I'll probably put the STL on Thingiverse.
Hi, thank you for the mod and follow step by step with ur video, one problem i faced is the foldable handle which cannot be tightened, the screws are a little bit longer and cannot be fully screw-in.
Hi my radioking tx18x I bought the charging board but I saw the 3 pin connection output is 8.4V at both yellow and red wire. I wondered it is correct? And bottom of the main board i have one same small 3 pin socket originally plugged with red and black wire and left center pin empty， now the new board can i just connect it's 3 wires 3pin connector onto it?
You can now get the USB C charging board from HobbyCool: bit.ly/T16UsbC Foldable Handle: bit.ly/T16FoldableHandle-HC Soon they are going to sell the foldable handle as well.
Nice upgrade. Do you know what's the deal with the T12? Seems to be out of stock everywhere. Is there a place I should look for official announcements from Jumper?
Question. I did the upgrade and the USB port doesn't seem to be working for charging or when connected to PC. I rechecked the ribbon connectors and they seem fine. Problem is red status light isn't going on (blinking or non) on the board. Any trouble shooting advice?
Gday Gal, very cool i cant wait to change my t16 to on board charging and folding handle for storing, any idea when these mods will be up for sale, great review nice work mate.👍🛸
@@KremerFPV The device plugged into your battery charge pack shown in video. Between pack and jumper, usb lead plugged into it the to it. GREEN IN COLOUR. 5.11 TIME
Had same problem, bad range and random failsafe on Jumper R1F receiver. frequency tuning, d8, d16 nothing helped so I just bought TBS crossfire micro and not a single failsafe or range problem :)
Yess! USB charging and USB c is what I was looking forward to.
Also does the USB c still work for using it as a control on a sim like the original usb does?
I just received mine and installed it in 10 mins. Working great! Thanks Gal.
Perfect. Have fun!
Always love your reviews. Detailed and good microphone quality. Can you recommend a Toothpick with a built in crossfire and long flight time?
Thanks! Check out my review of the Avantquads Kira / Vanta.
Who sells the chargeing board
jumper store in aliexpress
@@dndon2007 k ill wait untill someone in the states get them alliexpress has burnt me to many times i wont order on there anymore . But thank you much appreciated
@@jayward7536 I had many orders from aliexpress all the order went very slow in processing and shipping but when I order the jumper t16 from jumper store it takes only one month to delivered to me here in Saudi Arabia.. maybe grayson hobby will sell this board soon because they are sell jumper stuff in usa.. 👍
@@dndon2007 yea im sure they will have it . I can wait not that big of a deal is a nice little uprade for my t16 pro . If i get it from ali it takes like 2 months lol
@@jayward7536 Coming soon graysonhobby.com/jumper-t16-usb-type-c-board.html
you can order the charging board from jumper store in aliexpress I just saw it there
Thanks I will check it out.
Great video explaining everything in detail! Where'd you get that screwdriver I'm looking for a new one (the hex one)
Thanks! Please check the description of the video.
Where is the link to the new USB part?
graysonhobby.com/jumper-t16-usb-type-c-board.html
I will add the links once these parts will be available.
Really nice work, Gal! 😃
Thanks a lot!!!
Ordered the board and handle from my LHS here in the UK, the board comes with a new cover with the right cutout for USB C included.
Thanks for the update.
Does it come with a wall charger too? Thanks
No it doesn't.
where can i get the t16 with these new stuff on it already
Heli-Nation
hi very useful video. briefly and clearly !!!!!! you can leave a link to the updated handle. Pleas!!!!
Thanks Niko
I will update the links when the products will be available.
Is there a video for this type-C charging board upgrade on RadioKing TX18S??
No links to the kit Gal?
Soon
nice and informative, i just got the Tango 2 so lets see how that goes..
Thanks Eyal. I'm pretty sure that you will like it.
Where can we get the charging board? I want to install one into my T16, and perhaps my PowerPLAY with my printed back shell that makes it run off 18650's, Thingiverse 4080213
I have a USB 2S balance charger that came with a cheap RC car from Banggood, I discovered during testing it was actually a 1S charger that swapped which cell it was charging every few seconds. I'm really curios to test this one.
I will add the links once these parts will be available.
@Gal Kremer Thanks, I've just ordered 3 charging boards from that link you provided.
Because Jumper released the 3D model of their T16, I can modify the top plate for the USB-C socket and print a new one rather than melt the existing one. I'll probably put the STL on Thingiverse.
What tool do you have for the switch?
Please check the description of the video.
Hi, thank you for the mod and follow step by step with ur video, one problem i faced is the foldable handle which cannot be tightened, the screws are a little bit longer and cannot be fully screw-in.
Thanks. You can use some washers.
I had new shorter screws in the upgrade kit. Check for those VS. Original screws
Hi my radioking tx18x I bought the charging board but I saw the 3 pin connection output is 8.4V at both yellow and red wire. I wondered it is correct? And bottom of the main board i have one same small 3 pin socket originally plugged with red and black wire and left center pin empty， now the new board can i just connect it's 3 wires 3pin connector onto it?
Can these two parts be purchased separately? I would like to upgrade my current t16 to the foldable handle and USB c charging.
Yes, I added the relevant links to the description of the video.
One point. I didn't melt the hole for the TypeC connector and it fitted well for me. So I'm pretty sure you don't need to extend the hole.
What type of batteries does the charging board support? li-ion or lipo? 18650 batts only? Sorry I'm noob. Thanks!
It supports both.
Great info Gal.. Thank you...👍🏻🍻👊🏻
My pleasure.
Gal, my upgrade charging board didn't came with the 3-pin wire. Is it 1.25mm and any idea about the wire size?
Sorry but I am not sure. Were you able to figure it out?
Does this work with the t16pro?
of cause
Yep
You can now get the USB C charging board from HobbyCool: bit.ly/T16UsbC
Foldable Handle: bit.ly/T16FoldableHandle-HC
Soon they are going to sell the foldable handle as well.
nice video, also you don't need to extend the USB port hole in the top plastic, the new USB-C connector will fit just fine.
Thanks! It didn't fit properly on mine.
Nice upgrade. Do you know what's the deal with the T12? Seems to be out of stock everywhere. Is there a place I should look for official announcements from Jumper?
I'm pretty sure it was discontinued. You can get the T12 Pro which features an internal multiprotocol TX module.
@@KremerFPV Yeah saw the new model yesterday, looks sweet, still micro USB tho.
Question. I did the upgrade and the USB port doesn't seem to be working for charging or when connected to PC. I rechecked the ribbon connectors and they seem fine. Problem is red status light isn't going on (blinking or non) on the board. Any trouble shooting advice?
Either the board is defective or you didn't solder / connected it properly. When you put back the older board everything works fine now?
@@KremerFPV yeah. Trouble shot it with Grayson Hobby (where I bought it). Turns out it's a bad board. Reverted back to micro USB board
Does the charger turn off on completion of charge
Yes, it won't overcharge the battery.
Does anyone know if there is any chance this hack works for the t12 plus?
You can use it with any 2s balance plug.
Gal Kremer yeah but the circuit board layout is different on the t12+, the usb and the trainer port are farther apart in the case
@@SprayerFPV yes, it will require you to modify your TX.
Gday Gal, very cool i cant wait to change my t16 to on board charging and folding handle for storing, any idea when these mods will be up for sale, great review nice work mate.👍🛸
Thanks mate. Check the description of the video.
It's a transmitter. Remote controllers change the channel on your TV.
Well said.
If i get the usb charging board, do i need to change the sd/battery slot too?
No you don't.
Great. Ordered my charging board and foldable handle.
What is the device pluged into the battery charge pack ?
I'm not sure what you're referring to...
@@KremerFPV The device plugged into your battery charge pack shown in video. Between pack and jumper, usb lead plugged into it the to it. GREEN IN COLOUR. 5.11 TIME
SORRY TIME 2.22 MINS
@@normantrowell3767 bit.ly/USB-Meter-Tester
@@KremerFPV Thanks for prompt reply. Is it neccesary ? UM24 or UM24C ? Recomended
Probably a knucklehead question...Im assuming this mod is to be used with a standard 5 volt charger like the one for cell phones and such?
Yes, you can use it with pretty much any 5v USB charger.
👍👍👍👍👍
I think I will dremel the USB opening out . That melted case is bugging me ,lol. Good video though .
That's a good option too ;-)
Thanks!
Cool but you didn't give the reference of the charging plate 🙄
I will add the links once these parts will be available.
Gal, test the range this radio, because bad range. 😒
Which receiver are you using?
@@KremerFPV Jumper Pro ---> 70mw
Had same problem, bad range and random failsafe on Jumper R1F receiver. frequency tuning, d8, d16 nothing helped so I just bought TBS crossfire micro and not a single failsafe or range problem :)
20 Dollars for the Kit ... Great price. However 80 Dollars international shipping ... no way ...
I added more links, you can check it out
It's still big and heavy and it still uses that aweful Open Tx software. I don't see how it's more compact.