these videos is EXACTLY why I just spend $6000 on a 130w. It will be here 6/18/21. thank you for these.. makes it a much easier decision from some of the competitors
Thanks for this helpful video. I just setup my 55W OMTech laser today. First cuts (a simple 10mm circle) are showing a ghost circle offset by about 1.85mm to the left. I've cleaned the lenses and mirrors, but the defect is still there. What do you recommend next?
It turns out the first mirror was jostled in shipping. I followed the alignment video and adjusting the first mirror after the tube so the spot hit the Y target center fixed the ghosting. thanks for these videos. very helpful
Thanks for the video. Can you remove the built in fan or will it throw errors when you do. Im thinking of buying on the big ones but want to use the AC INFINITY system. would rather remove it than have an obstacle.
Noticed that my unit USB570a (bought in Sept 2022) does not have the same location for the lens as this video and others have displayed. My lens is located in the shaft/stem of the laser head instead. The tip (head) does unscrew and has the same silver ring but the lens is not even located there. Any suggestions? I can still access enough to clean but was just wondering as I would like to actually take it out completely to clean correctly.
I'd like to know about cleaning the laser tube. Best cleaning material to use, ect... I dont have a very dust free environment for my laser as it's in my workshop and has a coating of sawdust on it that i cant just blow off with my air compressor, it's hardened on there.
Hey there, thanks for reaching out!! We suggest cleaning your laser tube with Isopropyl alcohol. For further assistance, you can reach our Technical Support Team at omtechlaser.com/pages/contact-us
My tube has a blue part that does not unscrew and I can't get down to the o-ring that holds the lens in place. I have the 2.5" (I think) laser tube (new 80W AF2028). The blue part covers the dimples in the o-ring and even without that, there was nothing included in the kit to even reach into the tube to loosen the o-ring. Any suggestions or maybe even a video for the 2.5" tube?
I've had my laser for a month and all of a sudden in the middle of a job the output goes to nearly nothing. No matter how much I slow it down and add more power it won't even cut poster paper. Any suggestions ??
Good question! At any time one is losing power, we suggest checking their alignment. For further assistance, you can contact our Technical Support Team at omtechlaser.com/pages/contact-us
![[TH] JFT vs RLF - VCT Ascension Pacific - Day 2](http://i.ytimg.com/vi/PuIH7w_jO6c/mqdefault.jpg)
![PURPEECH - นี่ฉันเองคนที่... (It's me) [Official MV]](http://i.ytimg.com/vi/NuhHd0hOOg8/mqdefault.jpg)
Please keep posting informational videos about these machines, I plan on buying an 80w from you guys soon and would like to see more content
That's great to hear!! Feel free to message us with any questions about the 80W or our machines in general.
these videos is EXACTLY why I just spend $6000 on a 130w. It will be here 6/18/21. thank you for these.. makes it a much easier decision from some of the competitors
Thank you very very much. I greatly appreciate the information.
These videos are super helpful.
Thank you!! We're always here to assist.
Is this a general guide or for a specific model? Mine has a different setup for the laser head
Thanks for this helpful video. I just setup my 55W OMTech laser today. First cuts (a simple 10mm circle) are showing a ghost circle offset by about 1.85mm to the left. I've cleaned the lenses and mirrors, but the defect is still there. What do you recommend next?
It turns out the first mirror was jostled in shipping. I followed the alignment video and adjusting the first mirror after the tube so the spot hit the Y target center fixed the ghosting. thanks for these videos. very helpful
@@GridSpace No worries, we're glad that you're able to fix the issue!! Feel free to contact our Technical Support Team for other questions and advice.
Thanks for the video. Can you remove the built in fan or will it throw errors when you do. Im thinking of buying on the big ones but want to use the AC INFINITY system. would rather remove it than have an obstacle.
sir can I ask how can clean my laser tube inside. because to much dust inside the tube. thankyou
Noticed that my unit USB570a (bought in Sept 2022) does not have the same location for the lens as this video and others have displayed. My lens is located in the shaft/stem of the laser head instead. The tip (head) does unscrew and has the same silver ring but the lens is not even located there. Any suggestions? I can still access enough to clean but was just wondering as I would like to actually take it out completely to clean correctly.
Thax bro
You're welcome, bro!
I'd like to know about cleaning the laser tube. Best cleaning material to use, ect... I dont have a very dust free environment for my laser as it's in my workshop and has a coating of sawdust on it that i cant just blow off with my air compressor, it's hardened on there.
Hey there, thanks for reaching out!! We suggest cleaning your laser tube with Isopropyl alcohol. For further assistance, you can reach our Technical Support Team at omtechlaser.com/pages/contact-us
My tube has a blue part that does not unscrew and I can't get down to the o-ring that holds the lens in place. I have the 2.5" (I think) laser tube (new 80W AF2028). The blue part covers the dimples in the o-ring and even without that, there was nothing included in the kit to even reach into the tube to loosen the o-ring. Any suggestions or maybe even a video for the 2.5" tube?
We can definitely look into a future video! For the time being, feel free to contact our Technical Support Team for tips and further assistance.
Figured it out. Had to take a wrench to the blue collar to loosen it.
@@omtechlaser That would really help! I created one myself for others, but yours would be more professionally done!
I've had my laser for a month and all of a sudden in the middle of a job the output goes to nearly nothing. No matter how much I slow it down and add more power it won't even cut poster paper. Any suggestions ??
Good question! At any time one is losing power, we suggest checking their alignment. For further assistance, you can contact our Technical Support Team at omtechlaser.com/pages/contact-us